Current driver prevents command-line partitions from being parsed when built-in
partitions are defined in s3c2410_nand_set object, but it is not desirable in some
cases. This patch tries to parse commad-line partitions prior to the built-in.
Signed-off-by: Conke Hu <conke@maxwit.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* preset should be done before sending the reset command

* without this, I get the following error on an i.MX35 :
[    0.900000] ------------[ cut here ]------------
[    0.900000] WARNING: at kernel/irq/manage.c:290 __enable_irq+0x4c/0x88()
[    0.900000] Unbalanced enable for IRQ 33
[    0.900000] Modules linked in:
[    0.900000] [<c002ffb8>] (unwind_backtrace+0x0/0xf0) from [<c02f7d0c>] (dump_stack+0x18/0x1c)
[    0.900000] [<c02f7d0c>] (dump_stack+0x18/0x1c) from [<c0049a44>] (warn_slowpath_common+0x54/0x6c)
[    0.900000] [<c0049a44>] (warn_slowpath_common+0x54/0x6c) from [<c0049b00>] (warn_slowpath_fmt+0x38/0x40)
[    0.900000] [<c0049b00>] (warn_slowpath_fmt+0x38/0x40) from [<c008f65c>] (__enable_irq+0x4c/0x88)
[    0.900000] [<c008f65c>] (__enable_irq+0x4c/0x88) from [<c008fca0>] (enable_irq+0x54/0x98)
[    0.900000] [<c008fca0>] (enable_irq+0x54/0x98) from [<c021e618>] (wait_op_done+0x40/0x134)
[    0.900000] [<c021e618>] (wait_op_done+0x40/0x134) from [<c021e808>] (send_cmd+0x30/0x38)
[    0.900000] [<c021e808>] (send_cmd+0x30/0x38) from [<c021eb8c>] (mxc_nand_command+0x26c/0x328)
[    0.900000] [<c021eb8c>] (mxc_nand_command+0x26c/0x328) from [<c021aa60>] (nand_scan_ident+0x188/0x6c0)
[    0.900000] [<c021aa60>] (nand_scan_ident+0x188/0x6c0) from [<c001a9cc>] (mxcnd_probe+0x2b8/0x3d0)
[    0.900000] [<c001a9cc>] (mxcnd_probe+0x2b8/0x3d0) from [<c01f9e88>] (platform_drv_probe+0x20/0x24)
[    0.900000] [<c01f9e88>] (platform_drv_probe+0x20/0x24) from [<c01f8c38>] (driver_probe_device+0xb0/0x164)
[    0.900000] [<c01f8c38>] (driver_probe_device+0xb0/0x164) from [<c01f8d54>] (__driver_attach+0x68/0x8c)
[    0.900000] [<c01f8d54>] (__driver_attach+0x68/0x8c) from [<c01f8348>] (bus_for_each_dev+0x50/0x84)
[    0.900000] [<c01f8348>] (bus_for_each_dev+0x50/0x84) from [<c01f8a9c>] (driver_attach+0x20/0x28)
[    0.900000] [<c01f8a9c>] (driver_attach+0x20/0x28) from [<c01f7c00>] (bus_add_driver+0x144/0x2dc)
[    0.900000] [<c01f7c00>] (bus_add_driver+0x144/0x2dc) from [<c01f906c>] (driver_register+0xb0/0x13c)
[    0.900000] [<c01f906c>] (driver_register+0xb0/0x13c) from [<c01fa13c>] (platform_driver_register+0x4c/0x60)
[    0.900000] [<c01fa13c>] (platform_driver_register+0x4c/0x60) from [<c01fa170>] (platform_driver_probe+0x20/0xa0)
[    0.900000] [<c01fa170>] (platform_driver_probe+0x20/0xa0) from [<c001a708>] (mxc_nd_init+0x18/0x24)
[    0.900000] [<c001a708>] (mxc_nd_init+0x18/0x24) from [<c002938c>] (do_one_initcall+0x64/0x1bc)
[    0.900000] [<c002938c>] (do_one_initcall+0x64/0x1bc) from [<c00084c4>] (kernel_init+0xe8/0x1ac)
[    0.900000] [<c00084c4>] (kernel_init+0xe8/0x1ac) from [<c002aee8>] (kernel_thread_exit+0x0/0x8)
[    0.900000] ---[ end trace 8bf72ac6ba089a19 ]---
[    1.140000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unnesessary casts from void*.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unnesessary casts from void*.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unnesessary casts from void*.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unnesessary casts from void*.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unnesessary casts from void*.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Test if a lock or unlock function is present (pointer not NULL) before
calling it, to prevent a kernel dump.

Artem: removed extra blank lines
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Included the basic size info for NAND chips with ID of 0xAD or
0xD7. The first can be found in Hynix HY27SF161G2M, while the
second can be found in Micron MT29F64G08 and the Samsung K9LBG08U0D
(among others). Also, some 64 Gbit (or larger) chips identify as
0xD7 because they contain multiple smaller 32 Gbit chips. I
assume it's safe to classify these under the 32 Gbit listing.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This fixes:

	drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_resume':
	drivers/mtd/nand/mxc_nand.c:901: warning: unused variable 'host'

Removing this variable was missed in 9c14b153.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patchs adds a way for user space programs to find out whether a
flash sector is locked. An optional driver method in the mtd_info struct
provides the information.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add support for Macronix 25L8005.  Tested on a HP t5325 Thin Client.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There was a break missing so we returned -ENOTTY on success instead of
zero.  This was introduced by 048d8719: "mtd: blktrans: Hotplug fixes"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Look for dependency checks for "FOO" when inside of an "if FOO" block and remove them.
Signed-off-by: Kyle Spaans <kspaans@uwaterloo.ca>
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The rest of the function assumes that "data" can be null.  I don't know
the code well enough to say whether it can actually be null, but there
is no harm in checking here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

New inodes need to be locked as we're creating them, so they don't get used
by other things (like NFSd) before they're ready.

Pointed out by Al Viro.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Pointed out by Al Viro.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Move MTD_NAND_ECC and MTD_NAND_ECC_SMC above NAND memuconfig, to unbreak
display in xconfig. This shouldn't change any dependencies.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This turns out to be the reason for DMA timeouts on resume,
if card was inserted while system was suspended
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* Don't call complete on dma completion
* do a INIT_COMPLETE before using it each time
* Report DMA read error via ecc 'correct'

I finally managed to make my system do suspend to ram propertly, and I see that
if card was inserted during suspend (while system was off), I get dma timeouts
on resume. Simple card reinsert solves the issue.
This patch solves a crash that would happen otherwise
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Otherwise, if it fires right away, it might access
uninitialized spinlock
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In the example the module_init function should be static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* git://git.infradead.org/mtd-2.6: (154 commits)
  mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
  mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
  mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
  mtd: update gfp/slab.h includes
  jffs2: Stop triggering block erases from jffs2_write_super()
  jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
  jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
  jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
  jffs2: Wake GC thread when there are blocks to be erased
  jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
  jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
  mtd: mtdchar: Do not corrupt backing device of device node inode
  mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
  drivers/mtd: Use kmemdup
  mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
  mtd: nand: add Toshiba TC58NVG0 device ID
  pcmciamtd: add another ID
  pcmciamtd: coding style cleanups
  pcmciamtd: fixing obvious errors
  mtd: chips: add SST39WF160x NOR-flashes
  ...

Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c

* 'linux-next' of git://git.infradead.org/ubi-2.6:
  UBI: misc comment fixes
  UBI: fix s/then/than/ typos
  UBI: init even if MTD device cannot be attached, if built into kernel
  UBI: remove reboot notifier

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: mark VFS SB RO too

* 'for-linus' of git://oss.sgi.com/xfs/xfs: (54 commits)
  xfs: mark xfs_iomap_write_ helpers static
  xfs: clean up end index calculation in xfs_page_state_convert
  xfs: clean up mapping size calculation in __xfs_get_blocks
  xfs: clean up xfs_iomap_valid
  xfs: move I/O type flags into xfs_aops.c
  xfs: kill struct xfs_iomap
  xfs: report iomap_bn in block base
  xfs: report iomap_offset and iomap_bsize in block base
  xfs: remove iomap_delta
  xfs: remove iomap_target
  xfs: limit xfs_imap_to_bmap to a single mapping
  xfs: simplify buffer to transaction matching
  xfs: Make fiemap work in query mode.
  xfs: kill off l_sectbb_mask
  xfs: record log sector size rather than log2(that)
  xfs: remove dead XFS_LOUD_RECOVERY code
  xfs: removed unused XFS_QMOPT_ flags
  xfs: remove a few macro indirections in the quota code
  xfs: access quotainfo structure directly
  xfs: wait for direct I/O to complete in fsync and write_inode
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
  ocfs2: Silence a gcc warning.
  ocfs2: Don't retry xattr set in case value extension fails.
  ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
  ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
  fs/ocfs2/dlm: Use kstrdup
  fs/ocfs2/dlm: Drop memory allocation cast
  Ocfs2: Optimize punching-hole code.
  Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
  Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
  Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
  ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
  ocfs2: Wrap signal blocking in void functions.
  ocfs2/dlm: Increase o2dlm lockres hash size
  ocfs2: Make ocfs2_extend_trans() really extend.
  ocfs2/trivial: Code cleanup for allocation reservation.
  ocfs2: make ocfs2_adjust_resv_from_alloc simple.
  ocfs2: Make nointr a default mount option
  ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
  o2net: log socket state changes
  ocfs2: print node # when tcp fails
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
  [SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
  [SCSI] aacraid: prohibit access to array container space
  [SCSI] aacraid: add support for handling ATA pass-through commands.
  [SCSI] aacraid: expose physical devices for models with newer firmware
  [SCSI] aacraid: respond automatically to volumes added by config tool
  [SCSI] fcoe: fix fcoe module ref counting
  [SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
  [SCSI] libfcoe: Fix incorrect MAC address clearing
  [SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
  [SCSI] libfc: Move the port_id into lport
  [SCSI] fcoe: move link speed checking into its own routine
  [SCSI] libfc: Remove extra pointer check
  [SCSI] libfc: Remove unused fc_get_host_port_type
  [SCSI] fcoe: fixes wrong error exit in fcoe_create
  [SCSI] libfc: set seq_id for incoming sequence
  [SCSI] qla2xxx: Updates to ISP82xx support.
  [SCSI] qla2xxx: Optionally disable target reset.
  [SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
  [SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
  [SCSI] qla2xxx: T10 DIF support added.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
  USB: remove unused usb_buffer_alloc and usb_buffer_free macros
  usb: musb: update gfp/slab.h includes
  USB: ftdi_sio: fix legacy SIO-device header
  USB: kl5usb105: reimplement using generic framework
  USB: kl5usb105: minor clean ups
  USB: kl5usb105: fix memory leak
  USB: io_ti: use kfifo to implement write buffering
  USB: io_ti: remove unsused private counter
  USB: ti_usb: use kfifo to implement write buffering
  USB: ir-usb: fix incorrect write-buffer length
  USB: aircable: fix incorrect write-buffer length
  USB: safe_serial: straighten out read processing
  USB: safe_serial: reimplement read using generic framework
  USB: safe_serial: reimplement write using generic framework
  usb-storage: always print quirks
  USB: usb-storage: trivial debug improvements
  USB: oti6858: use port write fifo
  USB: oti6858: use kfifo to implement write buffering
  USB: cypress_m8: use kfifo to implement write buffering
  USB: cypress_m8: remove unused drain define
  ...

Fix up conflicts (due to usb_buffer_alloc/free renaming) in
	drivers/input/tablet/acecad.c
	drivers/input/tablet/kbtab.c
	drivers/input/tablet/wacom_sys.c
	drivers/media/video/gspca/gspca.c
	sound/usb/usbaudio.c

This is needed before the USB merge.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c