- 22 Jul, 2014 40 commits
-
-
Hans Verkuil authored
Now that the custom motion detection API in this driver has been replaced with a standard API there is no reason anymore to keep it in staging. So (finally!) move it to drivers/media/usb. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com>
-
Hans Verkuil authored
Now that the custom motion detection API has been replaced with a standard API there is no reason anymore to keep it in staging. So (finally!) move it to drivers/media/pci. Signed-off-by:
-
Philipp Zabel authored
Similarly to workbuf_size and tempbuf_size, store iram_size in the coda_devtype structure. This also decreases the IRAM used on i.MX6DL to 128 KiB. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
-
Philipp Zabel authored
Similarly to the work buffer size, store the temporary buffer size in the coda_devtype structure. Signed-off-by:
-
Philipp Zabel authored
We had the workbuf_size field since the beginning. Use it to tighten the code a little bit. Signed-off-by:
-
Philipp Zabel authored
This patch exports all auxiliary buffers, including SRAM, as debugfs binary blobs for debugging purposes. It shows, for example, that psbuf currently doesn't seem to be used at all on CODA7541, and that slicebuf and workbuf usage is far from the maximum. It can also be used to validate SRAM size allocation. Signed-off-by:
-
Philipp Zabel authored
When encoding into h.264, the input frame stride needs to be a multiple of 16. During allocation of the input buffers, it may not be known yet whether the encoder should create h.264 or not. Assume the worst and always use a frame stride that is a multiple of 16. Signed-off-by:
-
Philipp Zabel authored
CODA7541 only supports encoding h.264 frames with width and height that are multiples of the macroblock size. Signed-off-by:
-
Philipp Zabel authored
Even though the CODA h.264 decoder always decodes complete macroblocks, we can set the stride to the corresponding multiple of 16 and use a value smaller than that as real width. Unfortunately the same doesn't work for height, as there is no vertical linesperframe stride for discontiguous planar YUV frames. Signed-off-by:
-
Philipp Zabel authored
bytesperline is calculated in multiple places, store it in the coda_q_data structure. This will be more useful later when adding JPEG support. Signed-off-by:
-
Philipp Zabel authored
On i.MX53 and i.MX6, the CODA VPU can be reset by the System Reset Controller. We can use this to get out of dire situations, for example after a picture run timeout. Signed-off-by:
-
Philipp Zabel authored
Rename the per-context prescan_failed variable to hold, as this is what the flag does: it temporarily keeps the coda from running until new data is fed into the bitstream buffer or stop_streaming is called on the input side. A prescan failure on i.MX5 is one possible reason to enter this state, another one is a picture run timeout on i.MX6. Signed-off-by:
-
Philipp Zabel authored
The coda h.264 decoder also counts PIC_RUNs where no frame was decoded but a frame was rotated out / marked as ready to be displayed. This causes an offset between the incoming encoded frame's sequence number and the decode sequence number returned by the coda. This patch introduces a sequence counter offset variable to keep track of the difference. Signed-off-by:
-
Philipp Zabel authored
If the CODA reports macroblock errors, also set the VB2_BUF_STATE_ERROR flag to alert userspace. Signed-off-by:
-
Philipp Zabel authored
The coda driver advertises timestamp_type V4L2_BUF_FLAG_TIMESTAMP_COPY on both queues, so we have to copy timestamps from input v4l2 buffers to the corresponding destination v4l2 buffers. Since the h.264 decoder can reorder frames, a timestamp queue is needed to keep track of and assign the correct timestamp to destination buffers. Signed-off-by:
-
Michael Olbrich authored
In case no further buffers are queued after the stop command, restart job scheduling explicitly. Signed-off-by:
Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by:
-
Michael Olbrich authored
Some drivers might allow to decode remaining frames from an internal ringbuffer after a decoder stop command. Allow those to call v4l2_m2m_try_schedule directly. Signed-off-by:
-
Philipp Zabel authored
Allow userspace to enable cyclic intra refresh by setting the number of intra macroblocks per frame to a non-zero value. Signed-off-by:
-
Philipp Zabel authored
This adds controls for the h.264 deblocking loop filter. Signed-off-by:
-
Philipp Zabel authored
If the bitrate control is set, the encoder works in CBR mode, dynamically changing the quantization parameters to achieve a constant bitrate. With the min/max QP controls the quantization parameters can be limited to a given range. Signed-off-by:
-
Philipp Zabel authored
The driver uses the genalloc API, which doesn't have stubs in case GENERIC_ALLOCATOR is disabled. Signed-off-by:
-
Philipp Zabel authored
This adds a new function coda_check_firmware that does the firmware version checks so that this can be done only once from coda_probe instead of every time the runtime pm framework resumes the coda. Signed-off-by:
-
Philipp Zabel authored
This patch allows to use the runtime pm and generic pm domain frameworks to completely gate power to the VPU if it is unused. This functionality is available on i.MX6. Signed-off-by:
-
Philipp Zabel authored
v4l2_fh already contains a mem2mem context pointer. Use it. Signed-off-by:
-
Philipp Zabel authored
Use the mem2mem helpers introduced to get rid of some duplicated code. Signed-off-by:
-
Philipp Zabel authored
Using the coda_mutex lock to serialize hardware access would cause "INFO: possible circular locking dependency detected" lockdep warnings. Since the possible locking paths are hard to follow, serialize hardware access with a single workqueue thread. Ultimately the workqueue could be converted to only do register setup and readout for per-command work items. Using the initialized context property, SEQ_END is only queued in coda_release when needed. Signed-off-by:
-
Philipp Zabel authored
The h.264 decoder produces capture frames that are a multiple of the macroblock size (16 pixels). To inform userspace about invalid pixel data at the edges, use the active and padded composing rectangles on the capture queue. The cropping information is obtained from the h.264 sequence parameter set. Reviewed-by:
-
Philipp Zabel authored
This allows us to get rid of the now superfluous v4l2_m2m_get_vq check in G_FMT. Also, we can use this to check the buffer type in G_SELECTION later. Signed-off-by:
-
Philipp Zabel authored
This patch adds support for the CODA960 VPU in Freescale i.MX6 SoCs. It enables h.264 and MPEG4 encoding and decoding support. Besides the usual register shifting, the CODA960 gains frame memory control and GDI registers that are set up for linear mapping right now, needs ENC_PIC_SRC_INDEX to be set beyond the number of internal buffers for some reason, and has subsampling buffers that need to be set up. Also, the work buffer size is increased to 80 KiB. The CODA960 firmware spins if there is not enough input data in the bitstream buffer. To make it continue, buffers need to be copied into the bitstream as soon as they are queued. As the bitstream fifo is written into from two places, it must be protected with a mutex. For that, using a threaded interrupt handler is necessary. Signed-off-by:
-
Antti Palosaari authored
Rename driver namespace according to current driver name. Old msi3101 was name of reference design, msi2500 is name of chip itself. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
There was a lot of duplicated functionality between different stream format handling. Refactor functionality in order to get rid of duplicated code. Signed-off-by:
-
Antti Palosaari authored
Correct some style issues, mostly reported by checkpatch.pl. Signed-off-by:
-
Arun Kumar K authored
Latest MFC v6 firmware requires tile mode and loop filter setting to be done as part of Init buffer command, in sync with v7. This patch adds this support for new v6 firmware. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
Kiran AVND <avnd.kiran@samsung.com> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
-
Arun Kumar K authored
For MFC firmwares, improved versions with bug fixes and feature additions are released keeping the firmware version including major and minor number same. The issue came with the release of a new MFCv6 firmware with an interface change. This patch adds the support of accepting multiple firmware binaries for every version with the driver trying to load firmwares starting from latest. This ensures full backward compatibility regardless of which firmware version and kernel version is used. Signed-off-by:
-
Arun Kumar K authored
The function s5p_mfc_reload_firmware is exactly same as s5p_mfc_load_firmware. So removing the duplicate function. Signed-off-by:
-
Laurent Pinchart authored
X-Patchwork-Delegate: mchehab@redhat.com Replace the custom I2C read/write implementation with SMBUS functions to simplify the driver. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
X-Patchwork-Delegate: mchehab@redhat.com The driver mistakenly prints the ROM version instead of the device ID to the kernel log when detecting the chip. Fix it. Signed-off-by:
-
Paul Bolle authored
X-Patchwork-Delegate: mchehab@redhat.com Remove the CONFIG_ prefix from two Kconfig symbols in a dependency for SMS_SIANO_DEBUGFS. This prefix is invalid inside Kconfig files. Note that the current (common sense) dependency on SMS_USB_DRV and SMS_SDIO_DRV being equal ensures that SMS_SIANO_DEBUGFS will not violate its constraints. These constraint are that: - it should only be built if SMS_USB_DRV is set; - it can't be builtin if USB support is modular. So drop the dependency on SMS_USB_DRV, as it is unneeded. Fixes: 6c84b214 ("[media] sms: fix randconfig building error") Reported-by:
Martin Walch <walch.martin@web.de> Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
CrazyCat authored
Geniatech T220 init fixed - reset cmd from windows driver and fixed TS bus config for cxd2820r. Signed-off-by:
Evgeny Plehov <EvgenyPlehov@ukr.net> Signed-off-by:
-
CrazyCat authored
TS clock inversion in config. Signed-off-by:
-
