Skip to content

L
linux
Switch branch/tag
  1. 30 May, 2017 1 commit
    • Johannes Berg's avatar
      mac80211: fix TX aggregation start/stop callback race · 7a7c0a64
      Johannes Berg authored 
      When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:

 * associate
 * start aggregation session
 * driver callback
 * disassociate
 * associate again to the same AP
 * callback processing runs, leading to a WARN_ON() that
   the TID hadn't requested aggregation

If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.

Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: default avatarJouni Malinen <j@w1.fi>
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
      7a7c0a64
  3. 24 May, 2017 6 commits
    • David S. Miller's avatar
      Merge tag 'mac80211-for-davem-2017-05-23' of... · 029c5817
      David S. Miller authored 
      Merge tag 'mac80211-for-davem-2017-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two fixes this time:
 * fix the scheduled scan "BUG: scheduling while atomic"
 * check mesh address extension flags more strictly
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      029c5817
    • Alexander Potapenko's avatar
      net: rtnetlink: bail out from rtnl_fdb_dump() on parse error · 0ff50e83
      Alexander Potapenko authored 
      rtnl_fdb_dump() failed to check the result of nlmsg_parse(), which led
to contents of |ifm| being uninitialized because nlh->nlmsglen was too
small to accommodate |ifm|. The uninitialized data may affect some
branches and result in unwanted effects, although kernel data doesn't
seem to leak to the userspace directly.

The bug has been detected with KMSAN and syzkaller.

For the record, here is the KMSAN report:

==================================================================
BUG: KMSAN: use of unitialized memory in rtnl_fdb_dump+0x5dc/0x1000
CPU: 0 PID: 1039 Comm: probe Not tainted 4.11.0-rc5+ #2727
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16
 dump_stack+0x143/0x1b0 lib/dump_stack.c:52
 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007
 __kmsan_warning_32+0x66/0xb0 mm/kmsan/kmsan_instr.c:491
 rtnl_fdb_dump+0x5dc/0x1000 net/core/rtnetlink.c:3230
 netlink_dump+0x84f/0x1190 net/netlink/af_netlink.c:2168
 __netlink_dump_start+0xc97/0xe50 net/netlink/af_netlink.c:2258
 netlink_dump_start ./include/linux/netlink.h:165
 rtnetlink_rcv_msg+0xae9/0xb40 net/core/rtnetlink.c:4094
 netlink_rcv_skb+0x339/0x5a0 net/netlink/af_netlink.c:2339
 rtnetlink_rcv+0x83/0xa0 net/core/rtnetlink.c:4110
 netlink_unicast_kernel net/netlink/af_netlink.c:1272
 netlink_unicast+0x13b7/0x1480 net/netlink/af_netlink.c:1298
 netlink_sendmsg+0x10b8/0x10f0 net/netlink/af_netlink.c:1844
 sock_sendmsg_nosec net/socket.c:633
 sock_sendmsg net/socket.c:643
 ___sys_sendmsg+0xd4b/0x10f0 net/socket.c:1997
 __sys_sendmsg net/socket.c:2031
 SYSC_sendmsg+0x2c6/0x3f0 net/socket.c:2042
 SyS_sendmsg+0x87/0xb0 net/socket.c:2038
 do_syscall_64+0x102/0x150 arch/x86/entry/common.c:285
 entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.S:246
RIP: 0033:0x401300
RSP: 002b:00007ffc3b0e6d58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000401300
RDX: 0000000000000000 RSI: 00007ffc3b0e6d80 RDI: 0000000000000003
RBP: 00007ffc3b0e6e00 R08: 000000000000000b R09: 0000000000000004
R10: 000000000000000d R11: 0000000000000246 R12: 0000000000000000
R13: 00000000004065a0 R14: 0000000000406630 R15: 0000000000000000
origin: 000000008fe00056
 save_stack_trace+0x59/0x60 arch/x86/kernel/stacktrace.c:59
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:352
 kmsan_internal_poison_shadow+0xb1/0x1a0 mm/kmsan/kmsan.c:247
 kmsan_poison_shadow+0x6d/0xc0 mm/kmsan/kmsan.c:260
 slab_alloc_node mm/slub.c:2743
 __kmalloc_node_track_caller+0x1f4/0x390 mm/slub.c:4349
 __kmalloc_reserve net/core/skbuff.c:138
 __alloc_skb+0x2cd/0x740 net/core/skbuff.c:231
 alloc_skb ./include/linux/skbuff.h:933
 netlink_alloc_large_skb net/netlink/af_netlink.c:1144
 netlink_sendmsg+0x934/0x10f0 net/netlink/af_netlink.c:1819
 sock_sendmsg_nosec net/socket.c:633
 sock_sendmsg net/socket.c:643
 ___sys_sendmsg+0xd4b/0x10f0 net/socket.c:1997
 __sys_sendmsg net/socket.c:2031
 SYSC_sendmsg+0x2c6/0x3f0 net/socket.c:2042
 SyS_sendmsg+0x87/0xb0 net/socket.c:2038
 do_syscall_64+0x102/0x150 arch/x86/entry/common.c:285
 return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.S:246
==================================================================

and the reproducer:

==================================================================
  #include <sys/socket.h>
  #include <net/if_arp.h>
  #include <linux/netlink.h>
  #include <stdint.h>

  int main()
  {
    int sock = socket(PF_NETLINK, SOCK_DGRAM | SOCK_NONBLOCK, 0);
    struct msghdr msg;
    memset(&msg, 0, sizeof(msg));
    char nlmsg_buf[32];
    memset(nlmsg_buf, 0, sizeof(nlmsg_buf));
    struct nlmsghdr *nlmsg = nlmsg_buf;
    nlmsg->nlmsg_len = 0x11;
    nlmsg->nlmsg_type = 0x1e; // RTM_NEWROUTE = RTM_BASE + 0x0e
    // type = 0x0e = 1110b
    // kind = 2
    nlmsg->nlmsg_flags = 0x101; // NLM_F_ROOT | NLM_F_REQUEST
    nlmsg->nlmsg_seq = 0;
    nlmsg->nlmsg_pid = 0;
    nlmsg_buf[16] = (char)7;
    struct iovec iov;
    iov.iov_base = nlmsg_buf;
    iov.iov_len = 17;
    msg.msg_iov = &iov;
    msg.msg_iovlen = 1;
    sendmsg(sock, &msg, 0);
    return 0;
  }
==================================================================
Signed-off-by: default avatarAlexander Potapenko <glider@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0ff50e83
    • Quentin Schulz's avatar
      net: fec: add post PHY reset delay DT property · 159a0760
      Quentin Schulz authored 
      Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.

If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: default avatarQuentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Acked-by: default avatarFugang Duan <fugang.duan@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      159a0760
    • David S. Miller's avatar
      Merge branch 'sctp-dupcookie-fixes' · 11d3c949
      David S. Miller authored 
      Xin Long says:

====================
sctp: a bunch of fixes for processing dupcookie

After introducing transport hashtable and per stream info into sctp,
some regressions were caused when processing dupcookie, this patchset
is to fix them.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      11d3c949
    • Xin Long's avatar
      sctp: set new_asoc temp when processing dupcookie · 7e062977
      Xin Long authored 
      After sctp changed to use transport hashtable, a transport would be
added into global hashtable when adding the peer to an asoc, then
the asoc can be got by searching the transport in the hashtbale.

The problem is when processing dupcookie in sctp_sf_do_5_2_4_dupcook,
a new asoc would be created. A peer with the same addr and port as
the one in the old asoc might be added into the new asoc, but fail
to be added into the hashtable, as they also belong to the same sk.

It causes that sctp's dupcookie processing can not really work.

Since the new asoc will be freed after copying it's information to
the old asoc, it's more like a temp asoc. So this patch is to fix
it by setting it as a temp asoc to avoid adding it's any transport
into the hashtable and also avoid allocing assoc_id.

An extra thing it has to do is to also alloc stream info for any
temp asoc, as sctp dupcookie process needs it to update old asoc.
But I don't think it would hurt something, as a temp asoc would
always be freed after finishing processing cookie echo packet.
Reported-by: default avatarJianwen Ji <jiji@redhat.com>
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Acked-by: default avatarNeil Horman <nhorman@tuxdriver.com>
Acked-by: default avatarVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7e062977
    • Xin Long's avatar
      sctp: fix stream update when processing dupcookie · 3ab21379
      Xin Long authored 
      Since commit 3dbcc105 ("sctp: alloc stream info when initializing
asoc"), stream and stream.out info are always alloced when creating
an asoc.

So it's not correct to check !asoc->stream before updating stream
info when processing dupcookie, but would be better to check asoc
state instead.

Fixes: 3dbcc105 ("sctp: alloc stream info when initializing asoc")
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Acked-by: default avatarNeil Horman <nhorman@tuxdriver.com>
Acked-by: default avatarVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3ab21379
  5. 23 May, 2017 8 commits
  7. 22 May, 2017 14 commits
    • Kees Cook's avatar
      efi-pstore: Fix write/erase id tracking · c10e8031
      Kees Cook authored 
      Prior to the pstore interface refactoring, the "id" generated during
a backend pstore_write() was only retained by the internal pstore
inode tracking list. Additionally the "part" was ignored, so EFI
would encode this in the id. This corrects the misunderstandings
and correctly sets "id" during pstore_write(), and uses "part"
directly during pstore_erase().
Reported-by: default avatarMarta Lofstedt <marta.lofstedt@intel.com>
Fixes: 76cc9580 ("pstore: Replace arguments for write() API")
Fixes: a61072aa ("pstore: Replace arguments for erase() API")
Signed-off-by: default avatarKees Cook <keescook@chromium.org>
Tested-by: default avatarMarta Lofstedt <marta.lofstedt@intel.com>
      c10e8031
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · 86ca984c
      Linus Torvalds authored 
      Pull networking fixes from David Miller:
 "Mostly netfilter bug fixes in here, but we have some bits elsewhere as
  well.

   1) Don't do SNAT replies for non-NATed connections in IPVS, from
      Julian Anastasov.

   2) Don't delete conntrack helpers while they are still in use, from
      Liping Zhang.

   3) Fix zero padding in xtables's xt_data_to_user(), from Willem de
      Bruijn.

   4) Add proper RCU protection to nf_tables_dump_set() because we
      cannot guarantee that we hold the NFNL_SUBSYS_NFTABLES lock. From
      Liping Zhang.

   5) Initialize rcv_mss in tcp_disconnect(), from Wei Wang.

   6) smsc95xx devices can't handle IPV6 checksums fully, so don't
      advertise support for offloading them. From Nisar Sayed.

   7) Fix out-of-bounds access in __ip6_append_data(), from Eric
      Dumazet.

   8) Make atl2_probe() propagate the error code properly on failures,
      from Alexey Khoroshilov.

   9) arp_target[] in bond_check_params() is used uninitialized. This
      got changes from a global static to a local variable, which is how
      this mistake happened. Fix from Jarod Wilson.

  10) Fix fallout from unnecessary NULL check removal in cls_matchall,
      from Jiri Pirko. This is definitely brown paper bag territory..."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  net: sched: cls_matchall: fix null pointer dereference
  vsock: use new wait API for vsock_stream_sendmsg()
  bonding: fix randomly populated arp target array
  net: Make IP alignment calulations clearer.
  bonding: fix accounting of active ports in 3ad
  net: atheros: atl2: don't return zero on failure path in atl2_probe()
  ipv6: fix out of bound writes in __ip6_append_data()
  bridge: start hello_timer when enabling KERNEL_STP in br_stp_start
  smsc95xx: Support only IPv4 TCP/UDP csum offload
  arp: always override existing neigh entries with gratuitous ARP
  arp: postpone addr_type calculation to as late as possible
  arp: decompose is_garp logic into a separate function
  arp: fixed error in a comment
  tcp: initialize rcv_mss to TCP_MIN_MSS instead of 0
  netfilter: xtables: fix build failure from COMPAT_XT_ALIGN outside CONFIG_COMPAT
  ebtables: arpreply: Add the standard target sanity check
  netfilter: nf_tables: revisit chain/object refcounting from elements
  netfilter: nf_tables: missing sanitization in data from userspace
  netfilter: nf_tables: can't assume lock is acquired when dumping set elems
  netfilter: synproxy: fix conntrackd interaction
  ...
      86ca984c
    • Jiri Pirko's avatar
      net: sched: cls_matchall: fix null pointer dereference · 2d76b2f8
      Jiri Pirko authored 
      Since the head is guaranteed by the check above to be null, the call_rcu
would explode. Remove the previously logically dead code that was made
logically very much alive and kicking.

Fixes: 985538ee ("net/sched: remove redundant null check on head")
Signed-off-by: default avatarJiri Pirko <jiri@mellanox.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2d76b2f8
    • WANG Cong's avatar
      vsock: use new wait API for vsock_stream_sendmsg() · 499fde66
      WANG Cong authored 
      As reported by Michal, vsock_stream_sendmsg() could still
sleep at vsock_stream_has_space() after prepare_to_wait():

  vsock_stream_has_space
    vmci_transport_stream_has_space
      vmci_qpair_produce_free_space
        qp_lock
          qp_acquire_queue_mutex
            mutex_lock

Just switch to the new wait API like we did for commit
d9dc8b0f ("net: fix sleeping for sk_wait_event()").
Reported-by: default avatarMichal Kubecek <mkubecek@suse.cz>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: default avatarCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: default avatarStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      499fde66
    • Jarod Wilson's avatar
      bonding: fix randomly populated arp target array · 72ccc471
      Jarod Wilson authored 
      In commit dc9c4d0f, the arp_target array moved from a static global
to a local variable. By the nature of static globals, the array used to
be initialized to all 0. At present, it's full of random data, which
that gets interpreted as arp_target values, when none have actually been
specified. Systems end up booting with spew along these lines:

[   32.161783] IPv6: ADDRCONF(NETDEV_UP): lacp0: link is not ready
[   32.168475] IPv6: ADDRCONF(NETDEV_UP): lacp0: link is not ready
[   32.175089] 8021q: adding VLAN 0 to HW filter on device lacp0
[   32.193091] IPv6: ADDRCONF(NETDEV_UP): lacp0: link is not ready
[   32.204892] lacp0: Setting MII monitoring interval to 100
[   32.211071] lacp0: Removing ARP target 216.124.228.17
[   32.216824] lacp0: Removing ARP target 218.160.255.255
[   32.222646] lacp0: Removing ARP target 185.170.136.184
[   32.228496] lacp0: invalid ARP target 255.255.255.255 specified for removal
[   32.236294] lacp0: option arp_ip_target: invalid value (-255.255.255.255)
[   32.243987] lacp0: Removing ARP target 56.125.228.17
[   32.249625] lacp0: Removing ARP target 218.160.255.255
[   32.255432] lacp0: Removing ARP target 15.157.233.184
[   32.261165] lacp0: invalid ARP target 255.255.255.255 specified for removal
[   32.268939] lacp0: option arp_ip_target: invalid value (-255.255.255.255)
[   32.276632] lacp0: Removing ARP target 16.0.0.0
[   32.281755] lacp0: Removing ARP target 218.160.255.255
[   32.287567] lacp0: Removing ARP target 72.125.228.17
[   32.293165] lacp0: Removing ARP target 218.160.255.255
[   32.298970] lacp0: Removing ARP target 8.125.228.17
[   32.304458] lacp0: Removing ARP target 218.160.255.255

None of these were actually specified as ARP targets, and the driver does
seem to clean up the mess okay, but it's rather noisy and confusing, leaks
values to userspace, and the 255.255.255.255 spew shows up even when debug
prints are disabled.

The fix: just zero out arp_target at init time.

While we're in here, init arp_all_targets_value in the right place.

Fixes: dc9c4d0f ("bonding: reduce scope of some global variables")
CC: Mahesh Bandewar <maheshb@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: default avatarJarod Wilson <jarod@redhat.com>
Acked-by: default avatarAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      72ccc471
    • Rafael J. Wysocki's avatar
      Merge branches 'pm-sleep' and 'powercap' · bb47e964
      Rafael J. Wysocki authored 
      * pm-sleep:
  PM / hibernate: Declare variables as static
  RTC: rtc-cmos: Fix wakeup from suspend-to-idle
  PM / wakeup: Fix up wakeup_source_report_event()

* powercap:
  PowerCap: Fix an error code in powercap_register_zone()
      bb47e964
    • Rafael J. Wysocki's avatar
      Merge branches 'acpi-button' and 'acpi-tools' · e3170cc0
      Rafael J. Wysocki authored 
      * acpi-button:
  Revert "ACPI / button: Remove lid_init_state=method mode"

* acpi-tools:
  tools/power/acpi: Add .gitignore file
      e3170cc0
    • Rafael J. Wysocki's avatar
      Merge branches 'intel_pstate', 'pm-cpufreq' and 'pm-cpufreq-sched' · 079c1812
      Rafael J. Wysocki authored 
      * intel_pstate:
  cpufreq: intel_pstate: Document the current behavior and user interface

* pm-cpufreq:
  cpufreq: dbx500: add a Kconfig symbol

* pm-cpufreq-sched:
  cpufreq: schedutil: use now as reference when aggregating shared policy requests
      079c1812
    • David S. Miller's avatar
      net: Make IP alignment calulations clearer. · e4eda884
      David S. Miller authored 
      The assignmnet:

	ip_align = strict ? 2 : NET_IP_ALIGN;

in compare_pkt_ptr_alignment() trips up Coverity because we can only
get to this code when strict is true, therefore ip_align will always
be 2 regardless of NET_IP_ALIGN's value.

So just assign directly to '2' and explain the situation in the
comment above.
Reported-by: default avatar"Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e4eda884
    • Jarod Wilson's avatar
      bonding: fix accounting of active ports in 3ad · 751da2a6
      Jarod Wilson authored 
      As of 7bb11dc9 and 0622cab0, bond slaves in a 3ad bond are not
removed from the aggregator when they are down, and the active slave count
is NOT equal to number of ports in the aggregator, but rather the number
of ports in the aggregator that are still enabled. The sysfs spew for
bonding_show_ad_num_ports() has a comment that says "Show number of active
802.3ad ports.", but it's currently showing total number of ports, both
active and inactive. Remedy it by using the same logic introduced in
0622cab0 in __bond_3ad_get_active_agg_info(), so sysfs, procfs and
netlink all report the number of active ports. Note that this means that
IFLA_BOND_AD_INFO_NUM_PORTS really means NUM_ACTIVE_PORTS instead of
NUM_PORTS, and thus perhaps should be renamed for clarity.

Lightly tested on a dual i40e lacp bond, simulating link downs with an ip
link set dev <slave2> down, was able to produce the state where I could
see both in the same aggregator, but a number of ports count of 1.

MII Status: up
Active Aggregator Info:
        Aggregator ID: 1
        Number of ports: 2 <---
Slave Interface: ens10
MII Status: up <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1

MII Status: up
Active Aggregator Info:
        Aggregator ID: 1
        Number of ports: 1 <---
Slave Interface: ens10
MII Status: down <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: default avatarJarod Wilson <jarod@redhat.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      751da2a6
    • Alexey Khoroshilov's avatar
      net: atheros: atl2: don't return zero on failure path in atl2_probe() · bd703a15
      Alexey Khoroshilov authored 
      If dma mask checks fail in atl2_probe(), it breaks off initialization,
deallocates all resources, but returns zero.

The patch adds proper error code return value and
make error code setup unified.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: default avatarAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      bd703a15
    • Eric Dumazet's avatar
      ipv6: fix out of bound writes in __ip6_append_data() · 232cd35d
      Eric Dumazet authored 
      Andrey Konovalov and idaifish@gmail.com reported crashes caused by
one skb shared_info being overwritten from __ip6_append_data()

Andrey program lead to following state :

copy -4200 datalen 2000 fraglen 2040
maxfraglen 2040 alloclen 2048 transhdrlen 0 offset 0 fraggap 6200

The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen,
fraggap, 0); is overwriting skb->head and skb_shared_info

Since we apparently detect this rare condition too late, move the
code earlier to even avoid allocating skb and risking crashes.

Once again, many thanks to Andrey and syzkaller team.
Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
Reported-by: default avatarAndrey Konovalov <andreyknvl@google.com>
Tested-by: default avatarAndrey Konovalov <andreyknvl@google.com>
Reported-by: <idaifish@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      232cd35d
    • Linus Torvalds's avatar
      Linux 4.12-rc2 · 08332893
      Linus Torvalds authored
      08332893
    • Linus Torvalds's avatar
      x86: fix 32-bit case of __get_user_asm_u64() · 33c9e972
      Linus Torvalds authored 
      The code to fetch a 64-bit value from user space was entirely buggered,
and has been since the code was merged in early 2016 in commit
b2f68038 ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit
kernels").

Happily the buggered routine is almost certainly entirely unused, since
the normal way to access user space memory is just with the non-inlined
"get_user()", and the inlined version didn't even historically exist.

The normal "get_user()" case is handled by external hand-written asm in
arch/x86/lib/getuser.S that doesn't have either of these issues.

There were two independent bugs in __get_user_asm_u64():

 - it still did the STAC/CLAC user space access marking, even though
   that is now done by the wrapper macros, see commit 11f1a4b9
   ("x86: reorganize SMAP handling in user space accesses").

   This didn't result in a semantic error, it just means that the
   inlined optimized version was hugely less efficient than the
   allegedly slower standard version, since the CLAC/STAC overhead is
   quite high on modern Intel CPU's.

 - the double register %eax/%edx was marked as an output, but the %eax
   part of it was touched early in the asm, and could thus clobber other
   inputs to the asm that gcc didn't expect it to touch.

   In particular, that meant that the generated code could look like
   this:

        mov    (%eax),%eax
        mov    0x4(%eax),%edx

   where the load of %edx obviously was _supposed_ to be from the 32-bit
   word that followed the source of %eax, but because %eax was
   overwritten by the first instruction, the source of %edx was
   basically random garbage.

The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark
the 64-bit output as early-clobber to let gcc know that no inputs should
alias with the output register.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@kernel.org   # v4.8+
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      33c9e972
  9. 21 May, 2017 11 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7