Commit 4b5006ec ("shared DIU framebuffer support") added the ability to
retain the splash screen until the framebuffer is opened by user space.
Clean up this code to eliminate redundant writes to registers, and eliminate
the use of dummy area descriptor.
Signed-off-by: Timur Tabi <timur@freescale.com>

Probably left over from initial development in hardware cursor support
that never made it upstream.
Signed-off-by: Timur Tabi <timur@freescale.com>

Add some debug and error messages that are useful during debugging.
Signed-off-by: Timur Tabi <timur@freescale.com>

Remove functions request_irq_local() and free_irq_local(), and merge
their code into the functions that handle opening and closing the
framebuffer.  We also improve the way that interrupts are enabled.

Also implement a work-around for broken U-Boots that leave the DIU
interrupts enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>

The MPC5121 BSP comes with a gamma_set utility that initializes the gamma
table via an ioctl.  Unfortunately, the ioctl number that utility uses
is defined improperly, but we can still support it.
Signed-off-by: Timur Tabi <timur@freescale.com>

Allow the platform code not to define a value for diu_ops.set_monitor_port.
This would be for platforms that only have one monitor port.
set_monitor_port() will never be called with an unsupported port anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>

Timur has been cleaning up this driver, so just make it official.
Signed-off-by: Timur Tabi <timur@freescale.com>

The patch "drivers/video/gbefb.c: use devm_ functions" caused a
compile error.

drivers/video/gbefb.c:1159:16: error: implicit declaration of function
'devm_ioremap' [-Werror=implicit-function-declaration]
drivers/video/gbefb.c:1179:3: error: implicit declaration of function
'devm_ioremap_nocache' [-Werror=implicit-function-declaration]

Fix it by including linux/io.h which defines those functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Damien Cassou <damien.cassou@lifl.fr>

Omapdss driver changes for the 3.7 merge window.

Notable changes:

* Basic writeback support for DISPC level. Writeback is not yet usable, though,
  as we need higher level code to actually expose the writeback feature to
  userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
  between the omapdss and the panels, and this rewrite work moves us closer to
  that goal.
* Cleanup and restructuring patches that have been made while working on device
  tree support for omapdss. Device tree support is still some way ahead, but
  these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
  resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.

nuc900fb_map_video_memory is called by an devinit function
that may be called at run-time, but the function itself is
marked __init and will be discarded after boot.

To avoid calling into a function that may have been overwritten,
mark nuc900fb_map_video_memory itself as __devinit.

Without this patch, building nuc950_defconfig results in:

WARNING: drivers/video/built-in.o(.devinit.text+0x26c): Section mismatch in reference from the function nuc900fb_probe() to the function .init.text:nuc900fb_map_video_memory()
The function __devinit nuc900fb_probe() references
a function __init nuc900fb_map_video_memory().
If nuc900fb_map_video_memory is only used by nuc900fb_probe then
annotate nuc900fb_map_video_memory with a matching annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Save and restore register context of LCDC respectively
before suspend and after resume.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Add pm_runtime support to the da8xx-fb frame buffer driver.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.

Cc: stable@vger.kernel.org
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Both dpi.c and sdi.c use strcmp(), but do not include string.h. With
some Kconfig options string.h is included implicitly, but with some
other the compilation fails:

drivers/video/omap2/dss/dpi.c:407:5: error: implicit declaration of
function 'strcmp'

Include string.h in both dpi.c and sdi.c
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge omapdss writeback work. These patches implement the low level writeback
features in the DISPC, but do not yet add a way to actually use the writeback
from the userspace.

* archit/wb-dispc-for-3.7:
  OMAPDSS: DISPC: Configure color conversion coefficients for writeback
  OMAPDSS: DISPC: Add manager like functions for writeback
  OMAPDSS: DISPC: Configure writeback FIFOs
  OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
  OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
  OMAPDSS: DISPC: Add function to set channel in for writeback
  OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
  OMAPDSS: DISPC: Downscale chroma if plane is writeback
  OMAPDSS: DISPC: Configure input and output sizes for writeback
  OMAPDSS: DISPC: Add writeback register offsets and dss features structs
  OMAPDSS: DISPC: Allow both upscaling and downscaling of chroma
  OMAPDSS: DIPSC: Relax scaling limitations when in memory to memory mode
  OMAPDSS: DISPC: Don't pass channel out when configuring overlays
  OMAPDSS: DISPC: Make dispc_ovl_setup call dispc_ovl_setup_common
  OMAPDSS: OVERLAY: Add position and replication as overlay caps
  OMAPDSS: DISPC: Pass overlay caps as a parameter to dispc plane functions
  OMAPDSS: DISPC: Simplify function names for setting pipeline input and output sizes
  OMAPDSS: DISPC: Constify omap_overlay_info in dispc_ovl_setup()

Merge omapdss output work, that creates a new entity "output" to represent the
outputs (DPI, DSI, HDMI, ...) from DSS. An output sits in between an overlay
manager and a panel, and helps us to remove references to panel devices from
the omapdss core.

* archit/outputs-for-3.7: (23 commits)
  OMAPDSS: Remove old way of setting manager and device links
  OMAPDSS: APPLY: Remove omap_dss_device references from dss_ovl_enable/disable
  OMAPDSS: OVERLAY/MANAGER: Get device via output
  OMAPDSS: MANAGER: Update display sysfs store
  OMAPFB: Change dssdev->manager references
  OMAPDSS: HDMI: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: VENC: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: RFBI: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: SDI: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: DSI: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: DSI: Remove dsi_pdev_map global struct
  OMAPDSS: DPI: Replace dssdev->manager with dssdev->output->manager references
  OMAPDSS: Create links between managers, outputs and devices
  OMAPDRM: Remove manager->device references
  OMAPFB: remove manager->device references
  OMAP_VOUT: Remove manager->device references
  OMAPDSS: Remove manager->device references
  OMAPDSS: APPLY: Add manager set/unset output ops for omap_overlay_manager
  OMAPDSS: output: Add set/unset device ops for omap_dss_output
  OMAPDSS: outputs: Create and register output instances
  ...

Writeback pipeline receives RGB data from one of the overlays or one of the
overlay managers. If the target color mode is YUV422 or NV12, we need to convert
the RGB pixels to YUV. The scaler in WB then converts it to the target color
mode.

Hence, the color conversion coefficients that need to be programmed are the ones
which convert a RGB24 pixel to YUV444. Program these coefficients for writeback
pipeline.

Rearrange the code a bit to configure different coefficients for overlays and
writeback.
Signed-off-by: Archit Taneja <archit@ti.com>

Add functions to enable writeback, and set/check state of GO bit. These bits are
identical in behaviour with the corresponding overlay manager bits. Configure
them in a similar way to mgr_enable() and mgr_go_* functions. Add a helper to
get the FRAMEDONE irq corresponding to writeback.
Signed-off-by: Archit Taneja <archit@ti.com>

Extend the DISPC fifo functions to also configure the writeback FIFO thresholds.

The most optimal configuration for writeback is to push out data to the
interconnect the moment writeback pushes enough pixels in the FIFO to form a
burst. This reduces the chance of writeback overflowing it's FIFO.
Signed-off-by: Archit Taneja <archit@ti.com>

Configure some of the writeback specific parameters in dispc_wb_setup(). The
writeback parameters configured are:

truncation: This needs to be set if the color depth input to writeback is more
than the color depth of the color mode we want to store in memory.

writeback mode: This configures whether we want to use writeback in mem to mem
or capture mode. This information will be directly passed by APPLY later.
Signed-off-by: Archit Taneja <archit@ti.com>

Create struct omap_dss_writeback_info, this is similar to omap_overlay_info,
the major difference is that there is no parameter which describes the input
size to writeback, this is because this is always fixed, and decided by the
connected overlay or overlay manager. One more difference is that screen_width
is renamed to buf_width, to give the value of stride the writeback buffer has.

Call dispc_ovl_setup_common() through dispc_wb_setup() to configure overlay-like
parameters. The parameters in dispc_ovl_setup_common() which do not hold for
writeback are filled passed as zeroes or false, the code takes care of not
configuring them as they won't possess the needed overlay caps.
Signed-off-by: Archit Taneja <archit@ti.com>

Writeback can take input from either one of the overlays, or one of the overlay
managers. Add an enum which represents the channel_in for writeback, and maps
to the register field programming.

Add a function to configure channel in for writeback. This will be used later in
APPLY.
Signed-off-by: Archit Taneja <archit@ti.com>

The bit YUVCHROMARESAMPLING isn't there for writeback in DISPC_WB_ATTRIBUTES2.
It isn't there because we don't upsample chroma like for video pipelines, we
downsample chroma in writeback to get YUV422 or NV12 formats from the YUV444
input.

Ignore this bit in dispc_ovl_set_scaling_uv() if the plane is OMAP_DSS_WB.
Signed-off-by: Archit Taneja <archit@ti.com>

When converting YUYV444 content to YUV422 or NV12 formats through writeback
pipeline, the scaler needs to downscale the chroma plane. Ensure that chroma
is downscaled when the pipeline is writeback.
Signed-off-by: Archit Taneja <archit@ti.com>

Writeback uses the WB_PICTURE_SIZE register to define the size of the content
written to memory, this is the output of the scaler. It uses the WB_SIZE
register to define the size of the content coming from the overlay/manager to
which it is connected, this is the input to the scaler. This naming is different
as compared to overlays.

Add checks for writeback in dispc_ovl_set_input_size() and
dispc_ovl_set_output_size() to write to the correct registers.
Signed-off-by: Archit Taneja <archit@ti.com>

Since writeback has many overlay like properties, and most of it's registers are
similar to that of overlays, it's possible to reuse most of the overlay related
DISPC code for writeback when considering it as a plane. Writeback was added as
a plane in the omap_plane field as OMAP_DSS_WB.

Add the writeback register offsets in dispc.h, add minimal WB plane related info
needed in dss_features. Add a function which returns the number of writeback
pipelines an OMAP version has.
Signed-off-by: Archit Taneja <archit@ti.com>

In the function dispc_plane_set_scaling_uv(), create a parameter which tells if
we want to upscale or downscale the chroma plane.

Downscaling of chroma is required by writeback pipeline for converting the input
YUV444 color format to YUV422 or NV12.
Signed-off-by: Archit Taneja <archit@ti.com>

The scalers of overlays and writeback do not have any constraints on downscale
ratio when operating in memory to memory mode.

This is because in memory to memory mode, we aren't connected to a display which
needs data output at the rate of pixel clock. The scalers can perform as much
downscaling as needed, the rate at which the scaler outputs is adjusted
accordingly.

Relax constraints related to downscaling based on whether the input overlays are
connected to writeback in memory to memory mode. We pass a mem_to_mem boolean
parameter to dispc_ovl_setup() from APPLY. This is currently set to false, this
will later be configured to the correct value based on whether the overlay is
connected to writeback or not. Do the same later for writeback when writeback is
configured.

In the scaling calculation code, we calculate the minimum amount of core clock we
need to achieve the required downscaling. If we are in memory to memory mode, we
set this to a very small value(1 in this case), this value would always be
lesser than the actual DISPC core clock value, and hence the scaling checks
would succeed.

We take care that pixel clock isn't calculated for writeback and the overlays
connected to it when in memory to memory mode. A pixel clock in such cases
doesn't make sense.
Signed-off-by: Archit Taneja <archit@ti.com>

dispc_ovl_setup_common() is to be used by both overlays and writeback. We pass
channel out to figure out what manager the overlay is connected to, to determine
the pixel clock rate. This is used to decide the scaling limitations for that
overlay.

writeback doesn't have a channel out, it has a channel in field which tells
where writeback gets its input from. These are 2 different fields, and this
prevents us reusing the overlay configuration code for writeback.

To overcome this, we now pass omap_plane to overlay related functions rather
than passing channel out. We create helper functions which can derive pclk/lclk
from the omap_plane id.
Signed-off-by: Archit Taneja <archit@ti.com>

Add a new static function called dispc_ovl_setup_common(). This function is used by
dispc_ovl_setup() to configure the overlay registers. This split is done so that
dispc_wb_setup() can reuse overlay register configuration related code.
Signed-off-by: Archit Taneja <archit@ti.com>

Add position and replication as overlay caps, and pass overlay caps as an
argument to the corresponding functions. Adding position and replication to
overlay caps seems a bit unnecessary, but it allows us to use the
corresponding functions for writeback too.

These caps will be set for all overlays, but not for writeback. This is done
so writeback can reuse dispc_ovl_setup() to the maximum.
Signed-off-by: Archit Taneja <archit@ti.com>

Currently, the functions below take the omap_plane parameter and derive the
overlay caps within them. Pass the overlay caps as a parameter to the function
to allow these to be used by writeback too.

- dispc_ovl_set_zorder()
- dispc_ovl_set_pre_mult_alpha()
- dispc_ovl_setup_global_alpha()
- dispc_ovl_calc_scaling()
- dispc_ovl_setup()

These functions will be used for writeback later, and the caps will help in
deciding if they are to be used for writeback or not. This allows reuse of
overlay caps for writeback.

Using omap_overlay_caps for writeback seems a bit incorrect, but caps is
something already in use by users of OMAPDSS(omapfb/omap_vout), so we use
overlay caps for overlay like features of writeback too.
Signed-off-by: Archit Taneja <archit@ti.com>

The DISPC pipeline register names in the TRM for setting the buffer size and
the output size are a bit misleading, for example, there are different register
names for setting the buffer size for VID and GFX pipes. Things get more
confusing when considering writeback pipeline.

Rename the functions so that they tell whether they are configuring the input
to the scalar or the output. These will be extended later to support writeback
registers.
Signed-off-by: Archit Taneja <archit@ti.com>

The struct omap_overlay_info passed to dispc_ovl_setup() is used to configure
DISPC registers. It shouldn't modify the overlay_info structure. The pos_y field
was being changed in dispc_ovl_setup in the case of interlaced displays. Fix
this and const qualifier to the omap_overlay_info argument.
Signed-off-by: Archit Taneja <archit@ti.com>

Now that an omap_dss_output can be used to link between managers and devices, we
can remove the old way of setting manager and device links. This involves
removing the device and manager pointers from omap_overlay_manager and
omap_dss_device respectively, and removing the set_device/unset_device ops from
omap_overlay_manager.
Signed-off-by: Archit Taneja <archit@ti.com>