This patch just groups connection specific aggregation information
from struct aggr_info into a new structure (struct aggr_info_conn)
so that, in softAP mode, this can be used when each connected station
is made to have it's own aggregation state.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The patch "ath6kl: create core.c" removes wiphy_free() from
ath6kl_cfg80211_cleanup() and misses to free wiphy in
ath6kl_sdio_remove(). This patch fixes this regression.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The timer which is used to flush rx aggregation frames needs to
be disabled when resetting the aggregation state. This is found
in code review.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

John Linville had to revert the part of USB support which was already
in ath6kl due to build problems in commit cb00ec38 ("ath6kl: revert
USB support"). Now that I fixed the build problems properly by adding
ath6kl_core.ko kernel module it's possible to add back the
(incomplete) USB support. This patch is a revert of John's patch and
adds back the USB code which as already in ath6kl, only difference
being minor changes in Makefile and adapting usb.c to new core
function names.

Note that USB support in ath6kl is not complete yet. This code only
makes it possible to boot firmware but as HTC layer does not yet
support USB it's not possible to send any WMI commands nor data
packets to the firmware. That will be added soon.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Now ath6kl is ready for splitting core code to ath6kl_core.ko module.
This also makes it possible to link both sdio and usb code to kernel
at the same time, which earlier failed miserably.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

That way it's possible to not export debug_mask outside the upcoming
ath6kl_core.ko and that makes it easier to ath6kl_core.ko in the
following patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

We don't need it as debug calls already have a log level and compiler
should be smart enough to optimise away the code when ath6kl debug code
is not enabled. Also it makes it easier to abstract core code to
ath6kl_core.ko.

In ath6kl_dump_registers() I had to change the debug level from ANY to IRQ
as I removed the AR_DBG_LVL_CHECK() check before calling the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently core functions are spread between various files, group all
the functions into file and rename the functions to follow the style
used elsewhere in the driver. This will make it easier to a separate core
module.

Also fix a bug where wiphy is freed too early.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add ATH6KL_CONF_UART_DEBUG which is set whenever uart_debug module
parameter is enabled. This way we can keep the uart_debug parameter
static when core.c file is introduced.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Group them together and change the naming to follow the common style in
ath6kl. No functional changes.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl_cfg80211_vif_init/cleanup() follow more closely the style used
elsewhere in ath6kl.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add testmode 2 for 6003 ART. When you insmod ath6kl_sdio.ko testmode=2, ath6kl
will load ART firmware utf.bin and testscript nullTestFlow.bin. These files
should be put in the firmware folder.

kvalo: add "ath6kl:" to the title, word wrap the commit log and remove
extra line in the code
Signed-off-by: Alex Yang <xiaojuny@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Before I commited patch c1762a3f ("ath6kl: Add support for uAPSD") I
did a minor change how up variable is initialised in
ath6kl_process_uapsdq(). But I was sloppy and caused this compiler
warning:

txrx.c:88:5: warning: 'up' may be used uninitialized in this function

Revert my change to fix the warning.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

As drivers/net/wireless/ath/Makefile contains the flag to enable
endian checks there's no need to have it in ath6kl makefile anymore.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Commit c8f44aff ("net: introduce and use netdev_features_t for
device features sets") added netdev_features_t to ndo_set_features.
Change ath6kl to use the new type.

This fixes a warning:

ath6kl/main.c:1170: warning: initialization from incompatible pointer type
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Conflicts:
	drivers/net/wireless/ath/ath6kl/usb.c

ath6kl_read_fwlogs() assigns the value zero to the variable 'ret'
at the time of declaration. Later, return value of ath6kl_diag_read32()
repalces the init value. Hence removing useless zero assignment.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

* A new APSD power save queue is added in the station structure.
* When a station has APSD capability and goes to power save, the frame
  designated to the station will be buffered in APSD queue.
* When the host receives a frame which the firmware marked as trigger,
  host delivers the buffered frame from the APSD power save queue.
  Number of frames to deliver is decided by MAX SP length.
* When a station moves from sleep to awake state, all frames buffered
  in APSD power save queue are sent to the firmware.
* When a station is disconnected, all frames bufferes in APSD power save
  queue are dropped.
* When the host queues the first frame to the APSD queue or removes the
  last frame from the APSD queue, it is indicated to the firmware using
  WMI_AP_APSD_BUFFERED_TRAFFIC_CMD.

kvalo: fix buggy handling of sks queues, made it more obvious
the user priority when wmm is disabled, remove unneed else block and
combined some variable declarations
Signed-off-by: Thirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch addresses a few problems with the commit:

"ath6kl: Implement support for listen interval from userspace"

* The debugfs file required for reading/writing the listen interval
  wasn't created. Fix this.

* The interface index was being hardcoded to zero. Fix this.

* Two separate parameters, "listen_interval_time and listen_interval_beacons"
  were being used. This fails to work as expected because the FW assigns
  higher precedence to "listen_interval_beacons" and "listen_interval_time"
  ends up being never used at all.

  To handle this, fix the host driver to exclusively use listen interval
  based on units of beacon intervals.

To set the listen interval, a user would now do something like this:

echo "10" > /sys/kernel/debug/ieee80211/*/ath6kl/listen_interval

kvalo: fix two checkpatch warnings
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This prevents 'comp_pktq' from being used in an
incorrect manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

'params' is already used earlier and there is no point
in checking for a NULL condition again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

sdio_release_host() would be called twice if sdio_set_block_size()
fails for some reason, which would result in the following warning.

WARNING: at /home/sujith/dev/wireless-testing/drivers/mmc/core/core.c:828 mmc_release_host+0x42/0x50 [mmc_core]()

Call Trace:
[<ffffffff81064fdf>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106503a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa03beb42>] mmc_release_host+0x42/0x50 [mmc_core]
[<ffffffffa03c917e>] sdio_release_host+0x1e/0x30 [mmc_core]
[<ffffffffa053fac7>] ath6kl_sdio_config+0xc7/0x110 [ath6kl_sdio]
[<ffffffffa053fd2c>] ath6kl_sdio_probe+0x21c/0x320 [ath6kl_sdio]
[<ffffffffa03beb2a>] ? mmc_release_host+0x2a/0x50 [mmc_core]
[<ffffffffa03c7d2a>] sdio_bus_probe+0xfa/0x130 [mmc_core]
[<ffffffff813015ae>] driver_probe_device+0x7e/0x1b0
[<ffffffff8130178b>] __driver_attach+0xab/0xb0
[<ffffffff813016e0>] ? driver_probe_device+0x1b0/0x1b0
[<ffffffff813016e0>] ? driver_probe_device+0x1b0/0x1b0
[<ffffffff81300504>] bus_for_each_dev+0x64/0xa0
[<ffffffff8130123e>] driver_attach+0x1e/0x20
[<ffffffff81300e80>] bus_add_driver+0x1b0/0x280
[<ffffffffa0065000>] ? 0xffffffffa0064fff
[<ffffffff81301d06>] driver_register+0x76/0x140
[<ffffffffa0065000>] ? 0xffffffffa0064fff
[<ffffffffa03c7b71>] sdio_register_driver+0x21/0x30 [mmc_core]
[<ffffffffa0065012>] ath6kl_sdio_init+0x12/0x35 [ath6kl_sdio]
[<ffffffff81002042>] do_one_initcall+0x42/0x180
[<ffffffff810b025f>] sys_init_module+0x8f/0x200
[<ffffffff81425ac2>] system_call_fastpath+0x16/0x1b
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Commit 5b7c8406 ('ipv4: correct IGMP
behavior on v3 query during v2-compatibility mode') added yet another
case for query parsing, which can result in max_delay = 0.  Substitute
a value of 1, as in the usual v3 case.
Reported-by: Simon McVittie <smcv@debian.org>
References: http://bugs.debian.org/654876Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

More drivers where net_device_ops should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool_ops table of function pointers should be const.
Fix all the usb network drivers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

> net/core/sock.c: In function 'sk_update_clone':
> net/core/sock.c:1278:3: error: implicit declaration of function 'sock_update_memcg'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_uc_sync() and dev_mc_sync() are acquiring netif_addr_lock for
destination device of synchronization. Since netif_addr_lock is
already held at the time for source device, this triggers lockdep
deadlock warning.

There's no way this deadlock can happen so use spin_lock_nested() to
silence the warning.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently this race is handled but in a messy way an atomic
variable is being checked in a loop which sleeps upto ms
in every iteration. Remove this logic and use a mutex
to make sure irq is not disabled when irq handling is in
progress.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Otherwise if (ielen <= ATH6KL_MAX_IE) is dead code. It looks safe to
change the type of ielen from u8 to size_t instead of removing this
if check, this ielen can have the length of more than one ies in future.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In ath6kl_reset_device(), since control can never reach switch..case
when the target_type is neither TARGET_TYPE_AR6003 nor TARGET_TYPE_AR6004,
remove the default option of switch statement.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There are maximum of seven multicast filter are supported
by hw. When the requested number of filters exceeds the
maximum supported one, multicast filtering is completely
disabled, the requested filters will be configured in
firmware and the only multicast frames that host is interested
in will be passed to host for further processing otherwise.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

This will be used to disable/enable multicast receive.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>

so move it there.  Fixes build errors when CONFIG_INET is not defined:

In file included from include/linux/tcp.h:211:0,
                 from include/linux/ipv6.h:221,
                 from include/net/ipv6.h:16,
                 from include/linux/sunrpc/clnt.h:26,
                 from include/linux/nfs_fs.h:50,
                 from init/do_mounts.c:20:
include/net/sock.h: In function 'sk_update_clone':
include/net/sock.h:1109:3: error: implicit declaration of function 'sock_update_memcg' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver uses __napi_complete and napi_gro_receive. Without it, the
driver hits the BUG_ON(n->gro_list) assertion hard in __napi_complete.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Marin Glibic <zhilla2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 88271660 "pktgen: fix multiple queue warning" we added special
logic to handle the case where ntxq is zero.  It's not clear to me that
ntxq can actually be zero.  But if it were then we would set
->queue_map_min and ->queue_map_max to USHRT_MAX when probably we want
to set them to zero?
Signed-off-by: David S. Miller <davem@davemloft.net>

The energy detect enable/disable code in the driver uses some
register defines in this header unconditionally, so guarding
the smscphy.h header include with CONFIG_SMSC_PHY leads to
build failures in some configurations.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>