Pull libnvdimm updates from Dan Williams:
 "This adds a user for the new 'bytes-remaining' updates to
  memcpy_mcsafe() that you already received through Ingo via the
  x86-dax- for-linus pull.

  Not included here, but still targeting this cycle, is support for
  handling memory media errors (poison) consumed via userspace dax
  mappings.

  Summary:

   - DAX broke a fundamental assumption of truncate of file mapped
     pages. The truncate path assumed that it is safe to disconnect a
     pinned page from a file and let the filesystem reclaim the physical
     block. With DAX the page is equivalent to the filesystem block.
     Introduce dax_layout_busy_page() to enable filesystems to wait for
     pinned DAX pages to be released. Without this wait a filesystem
     could allocate blocks under active device-DMA to a new file.

   - DAX arranges for the block layer to be bypassed and uses
     dax_direct_access() + copy_to_iter() to satisfy read(2) calls.
     However, the memcpy_mcsafe() facility is available through the pmem
     block driver. In order to safely handle media errors, via the DAX
     block-layer bypass, introduce copy_to_iter_mcsafe().

   - Fix cache management policy relative to the ACPI NFIT Platform
     Capabilities Structure to properly elide cache flushes when they
     are not necessary. The table indicates whether CPU caches are
     power-fail protected. Clarify that a deep flush is always performed
     on REQ_{FUA,PREFLUSH} requests"

* tag 'libnvdimm-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
  dax: Use dax_write_cache* helpers
  libnvdimm, pmem: Do not flush power-fail protected CPU caches
  libnvdimm, pmem: Unconditionally deep flush on *sync
  libnvdimm, pmem: Complete REQ_FLUSH => REQ_PREFLUSH
  acpi, nfit: Remove ecc_unit_size
  dax: dax_insert_mapping_entry always succeeds
  libnvdimm, e820: Register all pmem resources
  libnvdimm: Debug probe times
  linvdimm, pmem: Preserve read-only setting for pmem devices
  x86, nfit_test: Add unit test for memcpy_mcsafe()
  pmem: Switch to copy_to_iter_mcsafe()
  dax: Report bytes remaining in dax_iomap_actor()
  dax: Introduce a ->copy_to_iter dax operation
  uio, lib: Fix CONFIG_ARCH_HAS_UACCESS_MCSAFE compilation
  xfs, dax: introduce xfs_break_dax_layouts()
  xfs: prepare xfs_break_layouts() for another layout type
  xfs: prepare xfs_break_layouts() to be called with XFS_MMAPLOCK_EXCL
  mm, fs, dax: handle layout changes to pinned dax mappings
  mm: fix __gup_device_huge vs unmap
  mm: introduce MEMORY_DEVICE_FS_DAX and CONFIG_DEV_PAGEMAP_OPS
  ...

Pull block fixes from Jens Axboe:
 "A few fixes for this merge window, where some of them should go in
  sooner rather than later, hence a new pull this week. This pull
  request contains:

   - Set of NVMe fixes, mostly follow up cleanups/fixes to the queue
     changes, but also teardown/removal and misc changes (Christop/Dan/
     Johannes/Sagi/Steve).

   - Two lightnvm fixes for issues that showed up in this window
     (Colin/Wei).

   - Failfast/driver flags inheritance for flush requests (Hannes).

   - The md device put sanitization and fix (Kent).

   - dm bio_set inheritance fix (me).

   - nbd discard granularity fix (Josef).

   - nbd consistency in command printing (Kevin).

   - Loop recursion validation fix (Ted).

   - Partition overlap check (Wang)"

[ .. and now my build is warning-free again thanks to the md fix  - Linus ]

* tag 'for-linus-20180608' of git://git.kernel.dk/linux-block: (22 commits)
  nvme: cleanup double shift issue
  nvme-pci: make CMB SQ mod-param read-only
  nvme-pci: unquiesce dead controller queues
  nvme-pci: remove HMB teardown on reset
  nvme-pci: queue creation fixes
  nvme-pci: remove unnecessary completion doorbell check
  nvme-pci: remove unnecessary nested locking
  nvmet: filter newlines from user input
  nvme-rdma: correctly check for target keyed sgl support
  nvme: don't hold nvmf_transports_rwsem for more than transport lookups
  nvmet: return all zeroed buffer when we can't find an active namespace
  md: Unify mddev destruction paths
  dm: use bioset_init_from_src() to copy bio_set
  block: add bioset_init_from_src() helper
  block: always set partition number to '0' in blk_partition_remap()
  block: pass failfast and driver-specific flags to flush requests
  nbd: set discard_alignment to the granularity
  nbd: Consistently use request pointer in debug messages.
  block: add verifier for cmdline partition
  lightnvm: pblk: fix resource leak of invalid_bitmap
  ...

Pull regulator updates from Mark Brown:
 "Quite a lot of core work this time around, though not 100% successful.

  We gained support for runtime mode changes thanks to David Collins and
  improved support for write only regulators (ones where we can't read
  back the configuration) from Douglas Anderson.

  There's been quite a bit of work from Linus Walleij on converting from
  specfying GPIOs by numbers to descriptors. Sadly the testing turned
  out to be less good than we had hoped and so a lot of this had to be
  reverted.

  We also have the start of updates to use coupled regulators from
  Maciej Purski, unfortunately there are further problems there so the
  last couple of patches have been reverted.

  We also have new drivers for BD71837 and SY8106A devices, SAW
  regulators on Qualcomm SPMI and dropped support for some preproduction
  chips that never made it to market from the AB8500 driver"

* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
  regulator: gpio: Revert
  ARM: pxa, regulator: fix building ezx e680
  regulator: Revert coupled regulator support again
  regulator: wm8994: Fix shared GPIOs
  regulator: max77686: Fix shared GPIOs
  regulator: bd71837: BD71837 PMIC regulator driver
  regulator: bd71837: Devicetree bindings for BD71837 regulators
  regulator: gpio: Get enable GPIO using GPIO descriptor
  regulator: fixed: Convert to use GPIO descriptor only
  regulator: s2mps11: Fix boot on Odroid XU3
  dt-bindings: qcom_spmi: Document SAW support
  regulator: qcom_spmi: Add support for SAW
  regulator: tps65090: Pass descriptor instead of GPIO number
  regulator: s5m8767: Pass descriptor instead of GPIO number
  regulator: pfuze100: Delete reference to ena_gpio
  regulator: max8952: Pass descriptor instead of GPIO number
  regulator: lp8788-ldo: Pass descriptor instead of GPIO number
  regulator: lm363x: Pass descriptor instead of GPIO number
  regulator: max8973: Pass descriptor instead of GPIO number
  regulator: mc13xxx-core: Switch to SPDX identifier
  ...

The problem here is that set_bit() and test_bit() take a bit number so
we should be passing 0 but instead we're passing (1 << 0) which leads to
a double shift.  It doesn't cause a runtime bug in the current code
because it's done consistently and we only set that one bit.

I decided to just re-use NVME_AER_NOTICE_NS_CHANGED instead of
introducing a new define for this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A controller reset after a run time change of the CMB module parameter
breaks the driver. An 'on -> off' will have the driver use NULL for the
host memory queue, and 'off -> on' will use mismatched queue depth between
the device and the host.

We could fix both, but there isn't really a good reason to change this
at run time anyway, compared to at module load time, so this patch makes
parameter read-only after after modprobe.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch ensures the nvme namsepace request queues are not quiesced
on a surprise removal. It's possible the queues were previously killed
in a failed reset, so the queues need to be unquiesced to ensure all
requests are flushed to completion.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The controller is required to disable its host memory buffer use on
controller reset. We don't need to submit an admin command to delete it,
so this patch skips sending that command so we don't need to worry about
handling a timeout.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We've been ignoring NVMe error status on queue creations. Fortunately they
are uncommon, but we should handle these anyway. This patch adds checks
for the a positive error return value that indicates an NVMe status.

If we do see a negative return, the controller isn't usable, so this
patch returns immediately in since we can't unwind that failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The nvme pci driver never unmaps the doorbell registers while the requests
are active, so we can always safely update the completion queue head.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The nvme pci driver no longer handles completions under the cq lock,
so the nested locking is not necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We should avoid consuming the newlines in traddr, trsvcid and
device_path. Add minimal processing to make sure they are gone.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The code was checking bit 20 instead of bit 2.  Also fixed the log entry.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Only take nvmf_transports_rwsem when doing a lookup of registered
transports, so that a blocking ->create_ctrl doesn't prevent other
actions on /dev/nvme-fabrics.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: increased lock hold time a bit to be safe, added a comment
 and updated the changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Quote from Figure 106 in NVMe 1.3a:

  The Identify Namespace data structure is returned to the host for the
  namespace specified in the Namespace Identifier (CDW1.NSID) field if it
  is an active NSID. If the specified namespace is not an active NSID,
  then the controller returns a zero filled data structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@rimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull arm64 updates from Catalin Marinas:
 "Apart from the core arm64 and perf changes, the Spectre v4 mitigation
  touches the arm KVM code and the ACPI PPTT support touches drivers/
  (acpi and cacheinfo). I should have the maintainers' acks in place.

  Summary:

   - Spectre v4 mitigation (Speculative Store Bypass Disable) support
     for arm64 using SMC firmware call to set a hardware chicken bit

   - ACPI PPTT (Processor Properties Topology Table) parsing support and
     enable the feature for arm64

   - Report signal frame size to user via auxv (AT_MINSIGSTKSZ). The
     primary motivation is Scalable Vector Extensions which requires
     more space on the signal frame than the currently defined
     MINSIGSTKSZ

   - ARM perf patches: allow building arm-cci as module, demote
     dev_warn() to dev_dbg() in arm-ccn event_init(), miscellaneous
     cleanups

   - cmpwait() WFE optimisation to avoid some spurious wakeups

   - L1_CACHE_BYTES reverted back to 64 (for performance reasons that
     have to do with some network allocations) while keeping
     ARCH_DMA_MINALIGN to 128. cache_line_size() returns the actual
     hardware Cache Writeback Granule

   - Turn LSE atomics on by default in Kconfig

   - Kernel fault reporting tidying

   - Some #include and miscellaneous cleanups"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (53 commits)
  arm64: Fix syscall restarting around signal suppressed by tracer
  arm64: topology: Avoid checking numa mask for scheduler MC selection
  ACPI / PPTT: fix build when CONFIG_ACPI_PPTT is not enabled
  arm64: cpu_errata: include required headers
  arm64: KVM: Move VCPU_WORKAROUND_2_FLAG macros to the top of the file
  arm64: signal: Report signal frame size to userspace via auxv
  arm64/sve: Thin out initialisation sanity-checks for sve_max_vl
  arm64: KVM: Add ARCH_WORKAROUND_2 discovery through ARCH_FEATURES_FUNC_ID
  arm64: KVM: Handle guest's ARCH_WORKAROUND_2 requests
  arm64: KVM: Add ARCH_WORKAROUND_2 support for guests
  arm64: KVM: Add HYP per-cpu accessors
  arm64: ssbd: Add prctl interface for per-thread mitigation
  arm64: ssbd: Introduce thread flag to control userspace mitigation
  arm64: ssbd: Restore mitigation status on CPU resume
  arm64: ssbd: Skip apply_ssbd if not using dynamic mitigation
  arm64: ssbd: Add global mitigation state accessor
  arm64: Add 'ssbd' command-line option
  arm64: Add ARCH_WORKAROUND_2 probing
  arm64: Add per-cpu infrastructure to call ARCH_WORKAROUND_2
  arm64: Call ARCH_WORKAROUND_2 on transitions between EL0 and EL1
  ...

Pull dmaengine updates from Vinod Koul:

 - updates to sprd, bam_dma, stm drivers

 - remove VLAs in dmatest

 - move TI drivers to their own subdir

 - switch to SPDX tags for ima/mxs dma drivers

 - simplify getting .drvdata on bunch of drivers by Wolfram Sang

* tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (32 commits)
  dmaengine: sprd: Add Spreadtrum DMA configuration
  dmaengine: sprd: Optimize the sprd_dma_prep_dma_memcpy()
  dmaengine: imx-dma: Switch to SPDX identifier
  dmaengine: mxs-dma: Switch to SPDX identifier
  dmaengine: imx-sdma: Switch to SPDX identifier
  dmaengine: usb-dmac: Document R8A7799{0,5} bindings
  dmaengine: qcom: bam_dma: fix some doc warnings.
  dmaengine: qcom: bam_dma: fix invalid assignment warning
  dmaengine: sprd: fix an NULL vs IS_ERR() bug
  dmaengine: sprd: Use devm_ioremap_resource() to map memory
  dmaengine: sprd: Fix potential NULL dereference in sprd_dma_probe()
  dmaengine: pl330: flush before wait, and add dev burst support.
  dmaengine: axi-dmac: Request IRQ with IRQF_SHARED
  dmaengine: stm32-mdma: fix spelling mistake: "avalaible" -> "available"
  dmaengine: rcar-dmac: Document R-Car D3 bindings
  dmaengine: sprd: Move DMA request mode and interrupt type into head file
  dmaengine: sprd: Define the DMA data width type
  dmaengine: sprd: Define the DMA transfer step type
  dmaengine: ti: New directory for Texas Instruments DMA drivers
  dmaengine: shdmac: Change platform check to CONFIG_ARCH_RENESAS
  ...

Pull IOMMU updates from Joerg Roedel:
 "Nothing big this time. In particular:

   - Debugging code for Tegra-GART

   - Improvement in Intel VT-d fault printing to prevent soft-lockups
     when on fault storms

   - Improvements in AMD IOMMU event reporting

   - NUMA aware allocation in io-pgtable code for ARM

   - Various other small fixes and cleanups all over the place"

* tag 'iommu-updates-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/io-pgtable-arm: Make allocations NUMA-aware
  iommu/amd: Prevent possible null pointer dereference and infinite loop
  iommu/amd: Fix grammar of comments
  iommu: Clean up the comments for iommu_group_alloc
  iommu/vt-d: Remove unnecessary parentheses
  iommu/vt-d: Clean up pasid quirk for pre-production devices
  iommu/vt-d: Clean up unused variable in find_or_alloc_domain
  iommu/vt-d: Fix iotlb psi missing for mappings
  iommu/vt-d: Introduce __mapping_notify_one()
  iommu: Remove extra NULL check when call strtobool()
  iommu/amd: Update logging information for new event type
  iommu/amd: Update the PASID information printed to the system log
  iommu/tegra: gart: Fix gart_iommu_unmap()
  iommu/tegra: gart: Add debugging facility
  iommu/io-pgtable-arm: Use for_each_set_bit to simplify code
  iommu/qcom: Simplify getting .drvdata
  iommu: Remove depends on HAS_DMA in case of platform dependency
  iommu/vt-d: Ratelimit each dmar fault printing

Pull MTD updates from Boris Brezillon:
 "Core changes:
   - Add a sysfs attribute to expose available OOB size

  Driver changes:
   - Remove HAS_DMA dependency on various drivers
   - Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
   - Replace msleep by usleep_range() in the dataflash driver
   - Avoid VLA usage in nftl layers
   - Remove useless .owner assignment in pismo
   - Fix various issues in the CFI driver
   - Improve TRX partition handling expose a DT compat for this part
     parser
   - Clarify OFFSET_CONTINUOUS meaning

  NAND core changes:
   - Add Miquel as a NAND maintainer
   - Add access mode to the nand_page_io_req struct
   - Fix kernel-doc in rawnand.h
   - Support bit-wise majority to recover from corrupted ONFI parameter
     pages
   - Stop checking FAIL bit after a SET_FEATURES, as documented in the
     ONFI spec

  Raw NAND Driver changes:
   - Fix and cleanup the error path of many NAND controller drivers
   - GPMI:
      + Cleanup/simplification of a few aspects in the driver
      + Take ECC setup specified in the DT into account
   - sunxi: remove support for GPIO-based R/B polling
   - MTK:
      + Use of_device_get_match_data() instead of of_match_device()
      + Add an entry in MAINTAINERS for this driver
      + Fix nand-ecc-step-size and nand-ecc-strength description in the
        DT bindings doc
   - fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page

  OneNAND driver changes:
   - samsung: use dev_get_drvdata() instead of platform_get_drvdata()

  SPI NOR core changes:
   - Add support for a bunch of SPI NOR chips
   - Clear EAR reg when switching to 3-byte addressing mode on Winbond
     chips

  SPI NOR controller driver changes:
   - cadence: Add DMA support for direct mode reads
   - hisi: Prefix a few functions with hisi_
   - intel:
      + Mark the driver as "dangerous" in Kconfig
      + Fix atomic sequence handling
      + Pass a 40us delay (instead of 0us) to readl_poll_timeout()
   - fsl:
      + fix a typo in a function name
      + add support for IP variants embedded in the ls2080a and ls1080a
        SoCs
   - stm32: request exclusive control of the reset line"

* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
  mtd: nand: Pass mode information to nand_page_io_req
  mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
  mtd: cfi_cmdset_0002: Change erase functions to check chip good only
  mtd: cfi_cmdset_0002: Change erase functions to retry for error
  mtd: cfi_cmdset_0002: Change definition naming to retry write operation
  mtd: cfi_cmdset_0002: Change write buffer to check correct value
  mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
  mtd: bcm47xxpart: add of_match_table with a new DT binding
  dt-bindings: mtd: document Broadcom's BCM47xx partitions
  mtd: spi-nor: Add support for EN25QH32
  mtd: spi-nor: Add support for is25wp series chips
  mtd: spi-nor: Add Winbond w25q32jv support
  mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
  mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
  mtd: spi-nor: intel: provide a range for poll_timout
  mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
  mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
  mtd: spi-nor: intel-spi: Fix atomic sequence handling
  mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
  mtd: rawnand: use bit-wise majority to recover the ONFI param page
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.18 development cycle.

  Core changes:

   - We have killed off VLA from the core library and all drivers.

     The background should be clear for everyone at this point:

        https://lwn.net/Articles/749064/

     Also I just don't like VLA's, kernel developers hate it when
     compilers do things behind their back. It's as simple as that.

     I'm sorry that they even slipped in to begin with. Kudos to Laura
     Abbott for exorcising them.

   - Support GPIO hogs in machines/board files.

  New drivers and chip support:

   - R-Car r8a77470 (RZ/G1C)

   - R-Car r8a77965 (M3-N)

   - R-Car r8a77990 (E3)

   - PCA953x driver improvements to accomodate more variants.

  Improvements and new features:

   - Support one interrupt per line on port A in the DesignWare dwapb
     driver.

  Misc:

   - Random cleanups, right header files in the drivers, some size
     optimizations etc"

* tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
  gpio: davinci: fix build warning when !CONFIG_OF
  gpio: dwapb: Fix rework support for 1 interrupt per port A GPIO
  gpio: pxa: Include the right header
  gpio: pl061: Include the right header
  gpio: pch: Include the right header
  gpio: pcf857x: Include the right header
  gpio: pca953x: Include the right header
  gpio: palmas: Include the right header
  gpio: omap: Include the right header
  gpio: octeon: Include the right header
  gpio: mxs: Switch to SPDX identifier
  gpio: Remove VLA from stmpe driver
  gpio: mxc: Switch to SPDX identifier
  gpio: mxc: add clock operation
  gpio: Remove VLA from gpiolib
  gpio: aspeed: Use a cache of output data registers
  gpio: aspeed: Set output latch before changing direction
  gpio: pca953x: fix address calculation for pcal6524
  gpio: pca953x: define masks for addressing common and extended registers
  gpio: pca953x: set the PCA_PCAL flag also when matching by DT
  ...

Pull HID updates from Jiri Kosina:

 - Valve Steam Controller support from Rodrigo Rivas Costa

 - Redragon Asura support from Robert Munteanu

 - improvement of duplicate usage handling in generic hid-input from
   Benjamin Tissoires

 - Win 8.1 precisioun touchpad spec implementation from Benjamin
   Tissoires

 - Support for "In Range" flag for Wacom Intuos/Bamboo devices from
   Jason Gerecke

 - other various assorted smaller fixes and improvements

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (27 commits)
  HID: rmi: use HID_QUIRK_NO_INPUT_SYNC
  HID: multitouch: fix calculation of last slot field in multi-touch reports
  HID: quirks: remove Delcom Visual Signal Indicator from hid_have_special_driver[]
  HID: steam: select CONFIG_POWER_SUPPLY
  HID: i2c-hid: remove i2c_hid_open_mut
  HID: wacom: Support "in range" for Intuos/Bamboo tablets where possible
  HID: core: fix hid_hw_open() comment
  HID: hid-plantronics: Re-resend Update to map button for PTT products
  HID: multitouch: fix types returned from mt_need_to_apply_feature()
  HID: i2c-hid: check if device is there before really probing
  HID: steam: add missing fields in client initialization
  HID: steam: add battery device.
  HID: add driver for Valve Steam Controller
  HID: alps: Fix some style in 't4_read_write_register()'
  HID: alps: Check errors returned by 't4_read_write_register()'
  HID: alps: Save a memory allocation in 't4_read_write_register()' when writing data
  HID: alps: Report an error if we receive invalid data in 't4_read_write_register()'
  HID: multitouch: implement precision touchpad latency and switches
  HID: multitouch: simplify the settings of the various features
  HID: multitouch: make use of HID_QUIRK_INPUT_PER_APP
  ...

Pull livepatching fixlet from Jiri Kosina:
 "livepatching documentation fix from Petr Mladek"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Remove not longer valid limitations from the documentation

Pull aio iopriority support from Al Viro:
 "The rest of aio stuff for this cycle - Adam's aio ioprio series"

* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: aio ioprio use ioprio_check_cap ret val
  fs: aio ioprio add explicit block layer dependence
  fs: iomap dio set bio prio from kiocb prio
  fs: blkdev set bio prio from kiocb prio
  fs: Add aio iopriority support
  fs: Convert kiocb rw_hint from enum to u16
  block: add ioprio_check_cap function

Pull proc_fill_cache regression fix from Al Viro:
 "Regression fix for proc_fill_cache() braino introduced when switching
  instantiate() callback to d_splice_alias()"

* 'work.lookup' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix proc_fill_cache() in case of d_alloc_parallel() failure

Pull xen updates from Juergen Gross:
 "This contains some minor code cleanups (fixing return types of
  functions), some fixes for Linux running as Xen PVH guest, and adding
  of a new guest resource mapping feature for Xen tools"

* tag 'for-linus-4.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/PVH: Make GDT selectors PVH-specific
  xen/PVH: Set up GS segment for stack canary
  xen/store: do not store local values in xen_start_info
  xen-netfront: fix xennet_start_xmit()'s return type
  xen/privcmd: add IOCTL_PRIVCMD_MMAP_RESOURCE
  xen: Change return type to vm_fault_t

Previously, mddev_put() had a couple different paths for freeing a
mddev, due to the fact that the kobject wasn't initialized when the
mddev was first allocated. If we move the kobject_init() to when it's
first allocated and just use kobject_add() later, we can clean all this
up.

This also removes a hack in mddev_put() to avoid freeing biosets under a
spinlock, which involved copying biosets on the stack after the reset
bioset_init() changes.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We can't just copy and clear a bio_set, use the bio helper to
setup a new bio_set with the settings from another one.

Fixes: 6f1c819c ("dm: convert to bioset_init()/mempool_init()")
Reported-by: Venkat R.B <vrbagal1@linux.vnet.ibm.com>
Tested-by: Venkat R.B <vrbagal1@linux.vnet.ibm.com>
Tested-by: Li Wang <liwang@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add a helper that allows a caller to initialize a new bio_set,
using the settings from an existing bio_set.
Reported-by: Venkat R.B <vrbagal1@linux.vnet.ibm.com>
Tested-by: Venkat R.B <vrbagal1@linux.vnet.ibm.com>
Tested-by: Li Wang <liwang@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Commit 17c28958 ("arm64: Abstract syscallno manipulation") abstracts
out the pt_regs.syscallno value for a syscall cancelled by a tracer
as NO_SYSCALL, and provides helpers to set and check for this
condition.  However, the way this was implemented has the
unintended side-effect of disabling part of the syscall restart
logic.

This comes about because the second in_syscall() check in
do_signal() re-evaluates the "in a syscall" condition based on the
updated pt_regs instead of the original pt_regs.  forget_syscall()
is explicitly called prior to the second check in order to prevent
restart logic in the ret_to_user path being spuriously triggered,
which means that the second in_syscall() check always yields false.

This triggers a failure in
tools/testing/selftests/seccomp/seccomp_bpf.c, when using ptrace to
suppress a signal that interrups a nanosleep() syscall.

Misbehaviour of this type is only expected in the case where a
tracer suppresses a signal and the target process is either being
single-stepped or the interrupted syscall attempts to restart via
-ERESTARTBLOCK.

This patch restores the old behaviour by performing the
in_syscall() check only once at the start of the function.

Fixes: 17c28958 ("arm64: Abstract syscallno manipulation")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reported-by: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Support for "In Range" flag for Wacom Intuos/Bamboo devices from Jason Gerecke

RMI4 correct split report handling from Benjamin Tissoires

- improvement of duplicate usage handling in hid-input from Benjamin Tissoires
- Win 8.1 precisioun touchpad spec implementation from Benjamin Tissoires

Assorted smaller fixes to i2c-hid driver

Valve Steam Controller support from Rodrigo Rivas Costa

Redragon Asura support from Robert Munteanu

hid-alps driver cleanups wrt. t4_read_write_register() handling
from Christophe Jaillet