Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.

Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the missing documentation that kernel-doc continually warns
about, to get rid of all that noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In typical cases, there's no need to pass both the maxattr
and the policy array pointer, as the maxattr should just be
ARRAY_SIZE(policy) - 1. Therefore, to be less error prone,
just remove the maxattr argument from the default macros
and deduce the size accordingly.

Leave the original macros with a leading underscore to use
here and in case somebody needs to pass a policy pointer
where the policy isn't declared in the same place and thus
ARRAY_SIZE() cannot be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge net-next so that we get the changes from net, which would
otherwise conflict with the NLA_POLICY_NESTED/_ARRAY changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix spelling mistake in cfg80211.h: "lenght" -> "length".
The typo is also in the special comment block which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There was a typo in the documentation for weight_multiplier in mac80211.h,
and the doc was missing entirely for airtime and airtime_weight in sta_info.h.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

WoL handling for the RTL8168 family is a little bit tricky because of
different types of broken BIOS and/or chip quirks.

Two known issues:
1. Network properly resumes from suspend only if WoL is enabled in the chip.
2. Some notebooks wake up immediately if system is suspended and network
   device is wakeup-enabled.

Few patches tried to deal with this:
7edf6d31 ("r8169: disable WOL per default")
18041b52 ("r8169: restore previous behavior to accept BIOS WoL
settings")

Currently we have the situation that the chip WoL settings as set by
the BIOS are respected (to prevent issue 1), but the device doesn't get
wakeup-enabled (to prevent issue 2).

This leads to another issue:
If systemd is told to set WoL it first checks whether the requested
settings are active already (and does nothing if yes). Due to the chip
WoL flags being set properly systemd assumes that WoL is configured
properly in our case. Result is that device doesn't get wakeup-enabled
and WoL doesn't work (until it's set e.g. by ethtool).

This patch now:
- leaves the chip WoL settings as is (to prevent issue 1)
- keeps the behavior to not wakeup-enable the device initially
  (to prevent issue 2)
- In addition we report WoL as being disabled in get_wol, matching
  that device isn't wakeup-enabled. If systemd is told to enable WoL,
  it will therefore detect that it has to do something and will
  call set_wol.

Of course the user still has the option to override this with
e.g. ethtool.

v2:
- Don't just exclude __rtl8169_get_wol() from compiling, remove it.
v3:
- adjust commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the macvlan_port_exists() macro with its twin from netdevice.h
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
code optimizations & bugfixes for HNS3 driver

This patchset includes bugfixes and code optimizations for the HNS3
ethernet controller driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.

This patch fixes it by only enabling it when first initialzing.

Fixes: 6871af29 ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When VF is resetting, it can't communicate to PF with mailbox msg.
This patch adds reset state checking before sending keep alive msg
to PF.

Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While hclge_init_umv_space() failed in the hclge_init_ae_dev(),
we should undo all the operation which has been done successfully,
the last success operation maybe hclge_mac_mdio_config(), so if
hclge_init_umv_space() failed, we also need to undo it.

Fixes: 288475b2ad01 ("{topost} net: hns3: refine umv space allocation")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rss result is more uniform when use recommended hash key from
microsoft, instead of the one generated by netdev_rss_key_fill().
Also using hash algorithm "xor" is better than "toeplitz".

This patch modifies the default hash key and hash algorithm.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver is unloading, if a global reset occurs,
unmap_ring_from_vector() in the hns3_nic_uninit_vector_data() will
fail, and hns3_nic_uninit_vector_data() just return. There may be
some netif_napi_del() not be done.

Since hardware will unmap all ring while resetting, so
hns3_nic_uninit_vector_data() should ignore this error, and do the
rest uninitialization.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver is unloading, if there is a calling of ndo_open occurs
between phy_disconnect() and unregister_netdev(), it will end up
causing the kernel to eventually hit a NULL deref:

[14942.417828] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000048
[14942.529878] Mem abort info:
[14942.551166]   ESR = 0x96000006
[14942.567070]   Exception class = DABT (current EL), IL = 32 bits
[14942.623081]   SET = 0, FnV = 0
[14942.639112]   EA = 0, S1PTW = 0
[14942.643628] Data abort info:
[14942.659227]   ISV = 0, ISS = 0x00000006
[14942.674870]   CM = 0, WnR = 0
[14942.679449] user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000224ad6ad
[14942.695595] [0000000000000048] pgd=00000021e6673003, pud=00000021dbf01003, pmd=0000000000000000
[14942.723163] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[14942.729358] Modules linked in: hns3(O) hclge(O) pv680_mii(O) hnae3(O) [last unloaded: hclge]
[14942.738907] CPU: 1 PID: 26629 Comm: kworker/u4:13 Tainted: G           O      4.18.0-rc1-12928-ga960791-dirty #145
[14942.749491] Hardware name: Huawei Technologies Co., Ltd. D05/D05, BIOS Hi1620 FPGA TB BOOT BIOS B763 08/17/2018
[14942.760392] Workqueue: events_power_efficient phy_state_machine
[14942.766644] pstate: 80c00009 (Nzcv daif +PAN +UAO)
[14942.771918] pc : test_and_set_bit+0x18/0x38
[14942.776589] lr : netif_carrier_off+0x24/0x70
[14942.781033] sp : ffff0000121abd20
[14942.784518] x29: ffff0000121abd20 x28: 0000000000000000
[14942.790208] x27: ffff0000164d3cd8 x26: ffff8021da68b7b8
[14942.795832] x25: 0000000000000000 x24: ffff8021eb407800
[14942.801445] x23: 0000000000000000 x22: 0000000000000000
[14942.807046] x21: 0000000000000001 x20: 0000000000000000
[14942.812672] x19: 0000000000000000 x18: ffff000009781708
[14942.818284] x17: 00000000004970e8 x16: ffff00000816ad48
[14942.823900] x15: 0000000000000000 x14: 0000000000000008
[14942.829528] x13: 0000000000000000 x12: 0000000000000f65
[14942.835149] x11: 0000000000000001 x10: 00000000000009d0
[14942.840753] x9 : ffff0000121abaa0 x8 : 0000000000000000
[14942.846360] x7 : ffff000009781708 x6 : 0000000000000003
[14942.851970] x5 : 0000000000000020 x4 : 0000000000000004
[14942.857575] x3 : 0000000000000002 x2 : 0000000000000001
[14942.863180] x1 : 0000000000000048 x0 : 0000000000000000
[14942.868875] Process kworker/u4:13 (pid: 26629, stack limit = 0x00000000c909dbf3)
[14942.876464] Call trace:
[14942.879200]  test_and_set_bit+0x18/0x38
[14942.883376]  phy_link_change+0x38/0x78
[14942.887378]  phy_state_machine+0x3dc/0x4f8
[14942.891968]  process_one_work+0x158/0x470
[14942.896223]  worker_thread+0x50/0x470
[14942.900219]  kthread+0x104/0x130
[14942.903905]  ret_from_fork+0x10/0x1c
[14942.907755] Code: d2800022 8b400c21 f9800031 9ac32044 (c85f7c22)
[14942.914185] ---[ end trace 968c9e12eb740b23 ]---

So this patch fixes it by modifying the timing to do phy_connect_direct()
and phy_disconnect().

Fixes: 256727da ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the VF shares the same TC config as PF, the business
running on PF and VF must have samiliar module.

For simplicity, we are not considering VF sharing the same tc
configuration as PF use case, so this patch removes the support
of TC configuration from VF and forcing VF to just use single
TC.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hnae3_register_ae_dev() may fail, and it should return a error code
to its caller, so change hnae3_register_ae_dev() return type to int.

Also, when hnae3_register_ae_dev() return error, hns3_probe() should
do some error handling and return the error code.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_close() stop the netdev and the service base on the netdev
will stop. But ndev->netdev_ops->ndo_stop() may only stop HW
and stack queue, the service base on the netdev can still work.

Fixes: 5668abda ("net: hns3: add support for set_ringparam")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In original codes, the .get_regs_len and .get_regs were missed
assigned. This patch fixes it.

Fixes: 1600c3e5 ("net: hns3: Support "ethtool -d" for HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Union l3_hdr_info and l4_hdr_info have already been defined in
the hns3_enet.h, so it is unnecessary to define them elsewhere.

This patch removes the redundant definition, and reuses the one
defined in the hns3_enet.h.
Signed-off-by: liyongxin <liyongxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Greg Ungerer says:

====================
net: dsa: mt7530: support MT7530 in the MT7621 SoC

This is the fourth version of a patch series supporting the MT7530 switch
as used in the MediaTek MT7621 SoC. Unlike the MediaTek MT7623 the MT7621
is built around a dual core MIPS CPU architecture. But inside it uses
basically the same 7530 switch.

This series resolves all issues I had with previous versions, and I can
now reliably use the driver on a 7621 SoC platform. These patches were
generated against linux-5.0-rc4.

The first patch enables support for the existing kernel mediatek ethernet
driver on the MT7621 SoC. This support is from Bjørn Mork, with an update
and fix by me. Using this driver fixed a number of problems I had
(TX checksums, large RX packet drop) over the staging driver
(drivers/staging/mt7621-eth).

Patch 2 modifies the mt7530 DSA driver to support the 7530 switch as
implemented in the Mediatek MT7621 SoC. The last patch updates the
devicetree bindings to reflect the new support in the mt7530 driver.

There is no real dependencies between the patches, so they can be taken
independantly.

Creating a new binding for the MT7621 seems like the only viable approach
to distinguish between a stand alone 7530 switch, the silicon module
in the MT7623 SoC and the silicon in the MT7621. Certainly the 7530 ID
register in the MT7623 and MT7621 returns the same value, "0x7530001".

Looking at the mt7530.c DSA driver it might make some sense to convert
the existing "mediatek,mcm" binding to something like "mediatek,mt7623"
to be consistent with this new MT7621 support. As far as I can tell
this is the intention of this binding.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devicetree binding to support the compatible mt7530 switch as used
in the MediaTek MT7621 SoC.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MediaTek MT7621 SoC device contains a 7530 switch, and the existing
linux kernel 7530 DSA switch driver can be used with it.

The bulk of the changes required stem from the 7621 having different
regulator and pad setup. The existing setup of these in the 7530
driver appears to be very specific to its implemtation in the Mediatek
7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM
based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).

Create a new devicetree type, "mediatek,mt7621", to support the 7530
switch in the 7621 SoC. There appears to be no usable ID register to
distinguish it from a 7530 in other hardware at runtime. This is used
to carry out the appropriate configuration and setup.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Mediatek MT7621 SoC contains the same ethernet hardware module as
used on a number of other MediaTek SoC parts. There are some minor
differences to deal with but we can use the same driver to support
them all.

This patch is based on work by Bjørn Mork <bjorn@mork.no>, and his
original patch is at:

https://github.com/bmork/LEDE/commit/3293bc63f5461ca1eb0bbc4ed90145335e7e3404

There is an additional compatible devicetree type added, and the primary
change to the code required is to support a single interrupt (for both
RX and TX interrupts).
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[gerg@kernel.org: rebase to mainline and irq handler fix]
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_acl: Include delta bits into hashtable key

The Spectrum-2 ASIC allows multiple rules to use the same mask provided
that the difference between their masks is small enough (up to 8
consecutive delta bits). A more detailed explanation is provided in
merge commit 756cd366 ("Merge branch
'mlxsw-Introduce-algorithmic-TCAM-support'").

These delta bits are part of the rule's key and therefore rules that
only differ in their delta bits can be inserted with the same A-TCAM
mask. In case two rules share the same key and only differ in their
priority, then the second will spill to the C-TCAM.

Current code does not take the delta bits into account when checking for
duplicate rules, which leads to unnecessary spillage to the C-TCAM.
This may result in reduced scale and performance.

Patch #1 includes the delta bits in the rule's key to avoid the above
mentioned problem.

Patch #2 adds a tracepoint when a rule is inserted into the C-TCAM.

Patches #3-#5 add test cases to make sure unnecessary spillage into the
C-TCAM does not occur.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure that the bug is fixed and we no longer have C-TCAM spill for two
keys that differ only in delta.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With recent fix in C-TCAM spillage for delta masks, the test stops to be
falsely positive. So fix it not to use delta by adding src_ip bits to the
masks. Alongside with that, use C-TCAM spill trace to see when the
spillage actually happens.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to specify number of trace hits and move helpers
to the beginning of the file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some visibility to the rule addition process and trace whenever rule
spilled into C-TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently only ERP mask masked bits in key are considered for
the hashtable key. That leads to false negative collisions
and fallbacks to C-TCAM in case two keys differ only in delta bits.

Fix this by taking full encoded key as a hashtable key,
including delta bits.
Reported-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: support SCTP_FUTURE/CURRENT/ALL_ASSOC

This patchset adds the support for 3 assoc_id constants: SCTP_FUTURE_ASSOC
SCTP_CURRENT_ASSOC, SCTP_ALL_ASSOC, described in rfc6458#section-7.2:

   All socket options set on a one-to-one style listening socket also
   apply to all future accepted sockets.  For one-to-many style sockets,
   often a socket option will pass a structure that includes an assoc_id
   field.  This field can be filled with the association identifier of a
   particular association and unless otherwise specified can be filled
   with one of the following constants:

   SCTP_FUTURE_ASSOC:  Specifies that only future associations created
      after this socket option will be affected by this call.

   SCTP_CURRENT_ASSOC:  Specifies that only currently existing
      associations will be affected by this call, and future
      associations will still receive the previous default value.

   SCTP_ALL_ASSOC:  Specifies that all current and future associations
      will be affected by this call.

The functions for many other sockopts that use assoc_id also need to be
updated accordingly.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_scheduler and
check with SCTP_FUTURE_ASSOC instead in sctp_getsockopt_scheduler,
it's compatible with 0.

SCTP_CURRENT_ASSOC is supported for SCTP_STREAM_SCHEDULER in this
patch. It also adds default_ss in sctp_sock to support
SCTP_FUTURE_ASSOC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_event and
check with SCTP_FUTURE_ASSOC instead in sctp_getsockopt_event,
it's compatible with 0.

SCTP_CURRENT_ASSOC is supported for SCTP_EVENT in this patch.

It also adds sctp_assoc_ulpevent_type_set() to make code more
readable.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_enable_strreset and
check with SCTP_FUTURE_ASSOC instead in sctp_getsockopt_enable_strreset,
it's compatible with 0.

SCTP_CURRENT_ASSOC is supported for SCTP_ENABLE_STREAM_RESET in this patch.
It also adjusts some code to keep a same check form as other functions.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_default_prinfo and
check with SCTP_FUTURE_ASSOC instead in sctp_getsockopt_default_prinfo,
it's compatible with 0.

SCTP_CURRENT_ASSOC is supported for SCTP_DEFAULT_PRINFO in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_deactivate_key.
SCTP_CURRENT_ASSOC is supported for SCTP_AUTH_DEACTIVATE_KEY in this
patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_del_key.
SCTP_CURRENT_ASSOC is supported for SCTP_AUTH_DELETE_KEY in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_auth_key.
SCTP_CURRENT_ASSOC is supported for SCTP_AUTH_ACTIVE_KEY in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check with SCTP_ALL_ASSOC instead in sctp_setsockopt_auth_key.
SCTP_CURRENT_ASSOC is supported for SCTP_AUTH_KEY in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>