Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The “file” sysfs entry for LUNs was writable even for non-removable
LUNs and the fsg_store_file() function did not check whether LUN is
removable or not.  This made it possible to change or even close
LUN's backing file.

The same is true for “ro” sysfs entry and LUNs simulating CD-ROM.
For those LUNs, the file should not be writable.

This commit introduces two new device_attribute structures for those
two special cases so that the file/ro sysfs entries are made
non-writable when not desired.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

A "usb0" interface that has never been connected to a host has an unknown
operstate, and therefore the IFF_RUNNING flag is (incorrectly) asserted
when queried by ifconfig, ifplugd, etc.  This is a result of calling
netif_carrier_off() too early in the probe function; it should be called
after register_netdev().

Similar problems have been fixed in many other drivers, e.g.:

    e826eafa (bonding: Call netif_carrier_off after register_netdevice)
    0d672e9f (drivers/net: Call netif_carrier_off at the end of the probe)
    6a3c869a (cxgb4: fix reported state of interfaces without link)

Fix is to move netif_carrier_off() to the end of the function.

Cc: stable@vger.kernel.org
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit adds pullup method implementation for UDC s3c-hsotg driver.
It is needed for e.g. CCG - Configurable Composite Gadget, when user space
configuration change request device disconnection from USB bus (done via
calling usb_gadget_connect/disconnect, which calls UDC's pullup method).

Implementation of pullup method has caused removal of phy_enable and
core_init methods from udc_start to pullup.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Currently, when a new value is stored to the “file” sysfs entry,
fsg_store_file() will release existing backing file and only then attempt to
open a new one.  If that fails, no new backing file is open.

This commit changes the fsg_lun_open() so that it closes existing backing file
only after the new backing file has been successfully opened.  With that
change, fsg_store_file() may use it to perform an atomic open operation with
guarantee that logical unit will either point to the new backing file or still
to the old one.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since f_mass_storage stopped using FSG_BUFFHD_STATIC_BUFFER (because it
caused buffers not to be page aligned which did not work well with at
least some UDCs), no code was using it.  Removing not to bloat the code
too much.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Failing to set max_speed prevents g_acm_ms working with many drivers which
check for driver->max_speed < USB_SPEED_FULL, including pxa25x_udc
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Moves clock initialization to the clock framework.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

With the new common clock infrastructure, the following clocks should be
used on i.MX drivers: ipg, per and ahb.

Adapt fsl_mxc_udc to follow this new behaviour to fix the following probe error:

Freescale High-Speed USB SOC Device Controller driver (Apr 20, 2007)
fsl-usb2-udc fsl-usb2-udc: clk_get("usb") failed
fsl-usb2-udc: probe of fsl-usb2-udc failed with error -2
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It supports Marvell USB 3.0 device controller for PXA2128 chip.
Signed-off-by: Yu Xu <yuxu@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

For SMP processors the spin_lock_irqsave is _only_ able to disable interrupt
on a core on which it is executed.

Therefore there may be a situation when other cores raise s3c-hsotg IRQ.
Then there are several places where critical sections can be overwritten.

To protect the above thread, a spin_lock in the interrupt handler has been
added. Due to coherent memory view (especially L1 cache) the spin lock
variable control access to IRQ handler only for one CPU core. In this way
serialization to access this driver is provided and hence several spin_lock_*
routines could be removed from IRQ handler's related functions.

The complete_request_lock function has been removed since all its calls
are performed from interrupt (spin lock protected) context.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The endpoint specific locks are replaced with a global lock.
This is crucial for running s3c-hsotg driver on a SMP SoC.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The hidg function driver currently handles its SET_REPORT calls via EP0.
This is the implicit behaviour when no OUT interrupt endpoint is
configured and generally works fine.

The problem is that due to EP0's role in the gadget framework, we cannot
hold back packets and control traffic flow to sync it to the char device,
and hence there's a high risk of loosing packets with this
implementation.

This patch adds an OUT interrupt endpoint to the interface and queues a
fix number of request to catch SET_REPORT events. According to the
specs, host drivers should always use the dedicated OUT endpoint when
present.

The char device's read implementation was rewritten to retrieve data
from the list of completed output requests.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit adds Documentation/usb/mass-storage.txt file.  It contains
description of how to use the mass storage gadget from user space.  It
elaborates on madule parameters and sysfs interface more then it was
written in the comments in the source code.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit removes thread_name and lun_name_format fields from the
fsg_config structure.  Those fields are not used by any in-tree code
and their usefulness is rather theoretical.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Prepare the clock before enabling it.

Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Prepare the clock before enabling it.

Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Prepare the clock before enabling it.

Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

bMaxBurst field on endpoint companion descriptor
is supposed to contain the number of burst minus
1. When passing that to controller drivers, we
should be passing the real number instead (by
incrementing 1).

While doing that, also fix the assumption on
dwc3 that value comes decremented by one.
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds super-speed support to UVC webcam gadget.

Also in this patch:
	- We add the configurability to pass bInterval, bMaxBurst, mult
	  factors for video streaming endpoint (ISOC IN) through module
	  parameters.

	- We use config_ep_by_speed helper routine to configure video
	  streaming endpoint.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds a MACRO for the UVC video control status (interrupt) endpoint and
removes the magic number which was being used earlier.

Some UDCs have issues supporting an interrupt IN endpoint having a max packet
size less than a particular value (say 32). It is easier in that case to simply
change the MACRO value instead of changing the max packet size value at a
number of locations.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usb: gadget: uvc: Fix string descriptor STALL issue when multiple uvc functions are added to a configuration

This patch solved the string descriptor STALL issue when we add multiple UVC
functions in a single configuration using a 'webcam.c' like composite driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When writing the descriptors to the ep0 file of functionfs, the HID descriptors where not recognized which caused the initialization from user space to fail.
Signed-off-by: Koen Beel <koen.beel@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

renesas_usbhs DMAEngine uses D0FIFO/D1FIFO,
but the data transfer direction should be fixed for keeping consistency.
This patch explain about it on renesas_usbhs.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit changes the default value of the removable module parameter
from “y” to “n”.  This comes with line with file_storag's default and
seems to be a better default.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

devm_* functions are used to replace kzalloc, request_mem_region, ioremap
and request_irq functions in probe call. With the usage of devm_* functions
explicit freeing and unmapping is not required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch makes use of the generic map/unmap
routines on the omap_udc driver. Removes
some useless and duplicated code.
Signed-off-by: Felipe Balbi <balbi@ti.com>

we don't need to check for _req because
kfree(NULL) is safe. Also, if someone
actually passes a NULL pointer to be freed
by usb_ep_free_request(), he deserves any
issue he faces.
Signed-off-by: Felipe Balbi <balbi@ti.com>

when allocating a request, it's better programming
practice to make sure we return NULL if allocation
failed.

This will ensure that, if struct usb_request isn't
the first member on our structure, we don't cheat
the gadget driver into thinking allocating worked
because pointer isn't 0.
Signed-off-by: Felipe Balbi <balbi@ti.com>

this also helps removing a few lines of boilerplate
code.
Signed-off-by: Felipe Balbi <balbi@ti.com>

that print isn't needed at all. Remove it
and move the use_dma reinitialization to
probe() function.

Note that ideally we would drop all
cpu_is_* and machine_is_* checks from
this driver instead. Later patches will
come to get rid of those.
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch is just a cleanup patch to make
checkpatch.pl a little happier with the
omap_udc.c driver.

No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>

There are no active users of this code for omap2 as
the boards in use have either TUSB or MUSB controller.

While at it, also fix warnings related to uninitialized
dc_clk and hhc_clk.

Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull device-mapper updates from Alasdair G Kergon:
 "Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>