Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2020-03-24

This series introduces some fixes to mlx5 driver.

From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask

Please pull and let me know if there is any problem.

For -stable v5.5
 ('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')

For -stable v5.4
 ('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
 ('net/mlx5e: Do not recover from a non-fatal syndrome')
 ('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
 ('net/mlx5e: Enhance ICOSQ WQE info fields')

The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.

[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839

Fixes: 003bd5b4 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.

Fix this by using devm_clk_get_optional() to handle this clock properly.

Fixes: b78ac6ec ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw.  It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc.  This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.

So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.

Fixes: d4619336 ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.

changelog:
V2->V3:
 - remove unnecessary whitespace cleanup
 - add the checks if port_rate is 0 before division

V1->V2:
 - combine variable "send_completed" into "last"
 - add the comment for estimate of the packet sending

Fixes: 585d763a ("net/sched: Introduce Credit Based Shaper (CBS) qdisc")
Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.

Fixes: 8276ea13 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.

In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:

- The buffers of the in-progress WQEs must be released
  and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.

For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().

Fixes: be5323c8 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.

Fixes: 8276ea13 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.

In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.

Fixes: be5323c8 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.

Link: https://lore.kernel.org/linux-rdma/88bab94d2fd72f3145835b4518bc63dda587add6.camel@redhat.com
Fixes: ab118da4 ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add missing Makefile for net/forwarding tests and include it to
the targets list, otherwise forwarding tests are not installed
in case of cross-compilation.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.

  ip link add veth1 type veth peer name veth2
  ethtool -s veth1 wol g
  ip link del veth1

Make sure dev_put() is called when ethtool_ops check fails.

v2: add Fixes tags

Fixes: a53f3d41 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe20 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3 ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.

Fixes: 5037d532 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes.

5 bug fix patches covering an indexing bug for priority counters, memory
leak when retrieving DCB ETS settings, error path return code, proper
disabling of PCI before freeing context memory, and proper ring accounting
in error path.

Please also apply these to -stable.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.

Fixes: 47558acd ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory.  Do the same sequence in the error path
of probe to be safe and consistent.

Fixes: c20dc142 ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed.  Fix it
by propagating the error code to the caller.

Fixes: 1b9394e5 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.

Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.

Fixes: 7df4ae9f ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is an indexing bug in determining these ethtool priority
counters.  Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index.  This index is then used
to obtain the proper CoS queue counter.  Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.

Fixes: e37fed79 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only attach macsec to ethernet devices.

Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.

Macvlan has a similar check in macvlan_port_create.

v1->v2
  - fix commit message typo
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike NL_SET_ERR_* macros, nl_set_extack_cookie_u64() and
nl_set_extack_cookie_u32() helpers do not check extack argument for null
and neither do their callers, as syzbot recently discovered for
ethnl_parse_header().

Instead of fixing the callers and leaving the trap in place, add check of
null extack to both helpers to make them consistent with NL_SET_ERR_*
macros.

v2: drop incorrect second Fixes tag

Fixes: 2363d73a ("ethtool: reject unrecognized request flags")
Reported-by: syzbot+258a9089477493cea67b@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1690 ProdID=7588 Rev=ff.ff
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

The nci_conn_max_data_pkt_payload_size() function sometimes returns
-EPROTO so "max_size" needs to be signed for the error handling to
work.  We can make "payload_size" an int as well.

Fixes: a06347c0 ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a place,

inet_dump_fib()
  fib_table_dump
    fn_trie_dump_leaf()
      hlist_for_each_entry_rcu()

without rcu_read_lock() will trigger a warning,

 WARNING: suspicious RCU usage
 -----------------------------
 net/ipv4/fib_trie.c:2216 RCU-list traversed in non-reader section!!

 other info that might help us debug this:

 rcu_scheduler_active = 2, debug_locks = 1
 1 lock held by ip/1923:
  #0: ffffffff8ce76e40 (rtnl_mutex){+.+.}, at: netlink_dump+0xd6/0x840

 Call Trace:
  dump_stack+0xa1/0xea
  lockdep_rcu_suspicious+0x103/0x10d
  fn_trie_dump_leaf+0x581/0x590
  fib_table_dump+0x15f/0x220
  inet_dump_fib+0x4ad/0x5d0
  netlink_dump+0x350/0x840
  __netlink_dump_start+0x315/0x3e0
  rtnetlink_rcv_msg+0x4d1/0x720
  netlink_rcv_skb+0xf0/0x220
  rtnetlink_rcv+0x15/0x20
  netlink_unicast+0x306/0x460
  netlink_sendmsg+0x44b/0x770
  __sys_sendto+0x259/0x270
  __x64_sys_sendto+0x80/0xa0
  do_syscall_64+0x69/0xf4
  entry_SYSCALL_64_after_hwframe+0x49/0xb3

Fixes: 18a8021a ("net/ipv4: Plumb support for filtering route dumps")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2020-03-05

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v5.4
 ('net/mlx5: DR, Fix postsend actions write length')

For -stable v5.5
 ('net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow')
 ('net/mlx5e: Fix endianness handling in pedit mask')
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When application uses TCP_QUEUE_SEQ socket option to
change tp->rcv_next, we must also update tp->copied_seq.

Otherwise, stuff relying on tcp_inq() being precise can
eventually be confused.

For example, tcp_zerocopy_receive() might crash because
it does not expect tcp_recv_skb() to return NULL.

We could add tests in various places to fix the issue,
or simply make sure tcp_inq() wont return a random value,
and leave fast path as it is.

Note that this fixes ioctl(fd, SIOCINQ, &val) at the same
time.

Fixes: ee995283 ("tcp: Initial repair mode")
Fixes: 05255b82 ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many systems build/test up-to-date kernels with older libcs, and
an older glibc (2.17) lacks the definition of SOL_DCCP in
/usr/include/bits/socket.h (it was added in the 4.6 timeframe).

Adding the definition to the test program avoids a compilation
failure that gets in the way of building tools/testing/selftests/net.
The test itself will work once the definition is added; either
skipping due to DCCP not being configured in the kernel under test
or passing, so there are no other more up-to-date glibc dependencies
here it seems beyond that missing definition.

Fixes: 11fb60d1 ("selftests: net: reuseport_addr_any: add DCCP")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.

Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.

This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.

Fixes: 81015539 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the DP83867 PHY is strapped to enable Fast Link Drop (FLD) feature
STRAP_STS2.STRAP_ FLD (reg 0x006F bit 10), the Energy Lost Threshold for
FLD Energy Lost Mode FLD_THR_CFG.ENERGY_LOST_FLD_THR (reg 0x002e bits 2:0)
will be defaulted to 0x2. This may cause the phy link to be unstable. The
new DP83867 DM recommends to always restore ENERGY_LOST_FLD_THR to 0x1.

Hence, restore default value of FLD_THR_CFG.ENERGY_LOST_FLD_THR to 0x1 when
FLD is enabled by bootstrapping as recommended by DM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we clean up devicetree related configuration
also when clock init fails.

Fixes: fecd4d7e ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.

This patch is a 1:1 copy of upstream slip.c commit f596c870
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Headers ionic_if.h and ionic_regs.h are licensed under three alternative
licenses and the used SPDX-License-Identifier expression makes
./scripts/spdxcheck.py complain:

drivers/net/ethernet/pensando/ionic/ionic_if.h: 1:52 Syntax error: OR
drivers/net/ethernet/pensando/ionic/ionic_regs.h: 1:52 Syntax error: OR

As OR is associative, it is irrelevant if the parentheses are put around
the first or the second OR-expression.

Simply add parentheses to make spdxcheck.py happy.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.

Test commands:
    ip netns del left
    ip netns del right
    modprobe -rv veth
    modprobe -rv hsr
    killall ping
    modprobe hsr
    ip netns add left
    ip netns add right
    ip link add veth0 type veth peer name veth1
    ip link add veth2 type veth peer name veth3
    ip link add veth4 type veth peer name veth5
    ip link set veth1 netns left
    ip link set veth3 netns right
    ip link set veth4 netns left
    ip link set veth5 netns right
    ip link set veth0 up
    ip link set veth2 up
    ip link set veth0 address fc:00:00:00:00:01
    ip link set veth2 address fc:00:00:00:00:02
    ip netns exec left ip link set veth1 up
    ip netns exec left ip link set veth4 up
    ip netns exec right ip link set veth3 up
    ip netns exec right ip link set veth5 up
    ip link add hsr0 type hsr slave1 veth0 slave2 veth2
    ip a a 192.168.100.1/24 dev hsr0
    ip link set hsr0 up
    ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
    ip netns exec left ip a a 192.168.100.2/24 dev hsr1
    ip netns exec left ip link set hsr1 up
    ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
	    fc:00:00:00:00:01 nud permanent
    ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
	    fc:00:00:00:00:01 nud permanent
    for i in {1..100}
    do
        ip netns exec left ping 192.168.100.1 &
    done
    ip netns exec left hping3 192.168.100.1 -2 --flood &
    ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
    ip netns exec right ip a a 192.168.100.3/24 dev hsr2
    ip netns exec right ip link set hsr2 up
    ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
	    fc:00:00:00:00:02 nud permanent
    ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
	    fc:00:00:00:00:02 nud permanent
    for i in {1..100}
    do
        ip netns exec right ping 192.168.100.1 &
    done
    ip netns exec right hping3 192.168.100.1 -2 --flood &
    while :
    do
        ip link add hsr0 type hsr slave1 veth0 slave2 veth2
	ip a a 192.168.100.1/24 dev hsr0
	ip link set hsr0 up
	ip link del hsr0
    done

Splat looks like:
[  120.954938][    C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[  120.957761][    C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[  120.959064][    C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[  120.960054][    C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  120.962261][    C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[  120.963149][    C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[  120.966277][    C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[  120.967293][    C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[  120.968516][    C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[  120.969718][    C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[  120.972203][    C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[  120.973379][    C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[  120.974410][    C0] FS:  00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[  120.979794][    C0] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  120.980773][    C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[  120.981945][    C0] Call Trace:
[  120.982411][    C0]  <IRQ>
[  120.982848][    C0]  ? hsr_add_node+0x8c0/0x8c0 [hsr]
[  120.983522][    C0]  ? rcu_read_lock_held+0x90/0xa0
[  120.984159][    C0]  ? rcu_read_lock_sched_held+0xc0/0xc0
[  120.984944][    C0]  hsr_handle_frame+0x1db/0x4e0 [hsr]
[  120.985597][    C0]  ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[  120.986289][    C0]  __netif_receive_skb_core+0x6bf/0x3170
[  120.992513][    C0]  ? check_chain_key+0x236/0x5d0
[  120.993223][    C0]  ? do_xdp_generic+0x1460/0x1460
[  120.993875][    C0]  ? register_lock_class+0x14d0/0x14d0
[  120.994609][    C0]  ? __netif_receive_skb_one_core+0x8d/0x160
[  120.995377][    C0]  __netif_receive_skb_one_core+0x8d/0x160
[  120.996204][    C0]  ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]

Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a75911 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luo bin says:

====================
hinic: BugFixes

Fix a number of bugs which have been present since the first commit.

The bugs fixed in these patchs are hardly exposed unless given
very specific conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

the minimum value of skb len that hw supports is 32 rather than 17
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the second input parameter of wait_for_completion_timeout should
be jiffies instead of millisecond
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add read barrier in driver code to keep from reading other fileds
in dma memory which is writable for hw until we have verified the
memory is valid for driver
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

should disable eq irq before freeing it, must clear event queue
depth in hw before freeing relevant memory to avoid illegal
memory access and update consumer idx to avoid invalid interrupt
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it's unreliable for fw to check whether IO is stopped, so driver
wait for enough time to ensure IO process is done in hw before
freeing resources
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>