- 06 Jan, 2014 14 commits
-
-
Mitch Williams authored
When communicating with VF devices over the AQ, the FW refers to the VF by its global VF ID, not local the VF ID with reference to its parent PF. Since the global and local VF IDs are identical for PF 0, the code worked correctly on PF 0. However, we cannot just use global IDs throughout the code as most of the other references to the VF (VSI setup, register offsets, etc.) require the local VF ID. Instead, we just add or subtract our base VF ID when sending and receiving AQ messages. Change-Id: I92f4332b4876bc68b2f9af9ebf48761f63b6bd97 Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Sibai Li <sibai.li@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mitch Williams authored
When SR-IOV is disabled, the (now nonexistent) virtual function devices undergo a VFLR event. We don't need to handle this event because the VFs are gone, but we do need to tell the HW that they are complete. This fixes an issue with a phantom VFLR and broken VFs when SR-IOV is re-enabled. Change-Id: I7580b49ded0158172a85b14661ec212af77000c8 Signed-off-by:
-
Mitch Williams authored
Shockingly, the compiler didn't flag this uninitialized variable. This fixes a potential memory corruption condition where ARQ messages are written to random memory locations. Change-Id: Iac82f4562d2bf3f42df3f3b2163d9cbed2160135 Signed-off-by:
-
Mitch Williams authored
Use struct assignment rather than an expensive memory copy. Change-Id: I1d18d510774dfd41a9c1250cdef238a4187528f5 Signed-off-by:
-
Greg Rose authored
Enabling the default port on the VEB causes all outgoing traffic from virtual functions to be copied to the physical function. The default port is only supposed to be used if you wish to bridge the physical function to a SW switch such as Open vSwitch or the Linux bridge. That allows the SW switch to route traffic to VMs that are not using a virtual function. Eventually we'll want to implement the ndo_fdb_add, ndo_fdb_del, and ndo_fdb_dump functions. The ndo_fdb_add function would set the default port on the VEB in those cases where the MAC/VLAN address filters have overflowed. Normally we would not want to use it. Change-Id: I3990f0384fff2840c4e43bc0955dd0b701380852 Signed-off-by:
Greg Rose <gregory.v.rose@intel.com> Signed-off-by:
-
Mitch Williams authored
We don't need to read the base VF id. It's already stashed in the HW struct. Change-Id: Ib81e2f76fc40b12c966e014a856b481912cafefc Signed-off-by:
-
Jesse Brandeburg authored
Trivial whitespace fix. Change-Id: Ib7c70891a33c4b3d200c69367549d0dbdee0f076 Signed-off-by:
-
Greg Rose authored
This patch fixes two different problems. 1) The port VLAN configuration was not persistent across VF driver loads and unloads. 2) The port VLAN configuration was only correct the first time it was set. Switching the port VLAN on and off would cause subsequent VLAN configurations to be corrupted in the VSI. Ensure that the correct bits are being set for the VSI port VLAN configuration. Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d Signed-off-by:
-
Anjali Singhai Jain authored
Save information that we can use while cleaning the tx ring. Also record the time_stamp since we will need it to check tx hangs. Change-Id: Ia3f1c17f6fec9bcb7fef2542d77eac7f6c4f115c Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by:
Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by:
-
Eyal Perry authored
Check if the device get enough bandwidth from the entire PCI chain to satisfy its capabilities. This patch determines the PCIe device's bandwidth capabilities by reading its PCIe Link Capabilities registers and then call the pcie_get_minimum_link function to ensure that the adapter is hooked into a slot which is capable of providing the necessary bandwidth capabilities. Signed-off-by:
Eyal Perry <eyalpe@mellanox.com> Signed-off-by:
Amir Vadai <amirv@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to i40e only. Anjali provides two cleanups to remove unnecessary code and a fix to resolve debugfs dumping only half the NVM. Then provides a fix to ethtool NVM reads where shadow RAM was used instead of actual NVM reads. Jesse provides a couple of fixes, one removes custom i40e functions which duplicate existing kernel functionality. Second fixes constant cast issues by replacing __constant_htons with htons. Mitch provides a couple of fixes for the VF interfaces in i40e. First provides a fix to guard against VF message races with can cause a panic. Second fix reinitializes the buffer size each time we clean the ARQ, because subsequent messages can be truncated. Lastly adds functionality to enable/disable ICR 0 dynamically. Vasu adds a simple guard against multiple includes of the i40e_txrx.h file. Shannon provides a couple of fixes, first fix swaps a couple of lines around in the error handling if the allocation for the VSI array fails. Second fixes an issue where we try to free the q_vector that has not been setup which can panic the kernel. David provides a patch to save off the point to memory and the length of 2 structs used in the admin queue in order to store all info about allocated kernel memory. Neerav fixes ring allocation where allocation and clearing of rings for a VSI should be using the alloc_queue_pairs and not num_queue_pairs. Then removes the unused define for multi-queue enabled. ==================== Signed-off-by: -
Hannes Frederic Sowa authored
macvlan needs vlan_pcpu_stats so make it visible even if compiling without VLAN_8021Q support. Otherwise a very long compiler error happens. Fixes: cdf3e274 ("macvlan: unify macvlan_pcpu_stats and vlan_pcpu_stats") Cc: Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-By:
Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
-
Daniel Borkmann authored
netdev_kobject_init() is only being called from __init context, that is, net_dev_init(), so annotate it with __init as well, thus the kernel can take this as a hint that the function is used only during the initialization phase and free up used memory resources after its invocation. Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== netfilter/IPVS updates for net-next The following patchset contains Netfilter updates for your net-next tree, they are: * Add full port randomization support. Some crazy researchers found a way to reconstruct the secure ephemeral ports that are allocated in random mode by sending off-path bursts of UDP packets to overrun the socket buffer of the DNS resolver to trigger retransmissions, then if the timing for the DNS resolution done by a client is larger than usual, then they conclude that the port that received the burst of UDP packets is the one that was opened. It seems a bit aggressive method to me but it seems to work for them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a new NAT mode to fully randomize ports using prandom. * Add a new classifier to x_tables based on the socket net_cls set via cgroups. These includes two patches to prepare the field as requested by Zefan Li. Also from Daniel Borkmann. * Use prandom instead of get_random_bytes in several locations of the netfilter code, from Florian Westphal. * Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack mark, also from Florian Westphal. * Fix compilation warning due to unused variable in IPVS, from Geert Uytterhoeven. * Add support for UID/GID via nfnetlink_queue, from Valentina Giusti. * Add IPComp extension to x_tables, from Fan Du. ==================== Signed-off-by:
-
- 05 Jan, 2014 26 commits
-
-
Anjali Singhai Jain authored
Driver needs to clean PBA only when interrupts are turned off and we are polling instead. Change-Id: Ic0c1da761bd3abe7f73b1cc8bcddf8e3a232fd0f Signed-off-by:
-
Anjali Singhai Jain authored
These functions don't need a prototype as they are defined in the file before they are called. Change-Id: Ie17ffad4a29a9c0df434c4ebc4681128a6095c65 Signed-off-by:
-
Neerav Parikh authored
Remove references to I40E_FLAG_MQ_ENABLED from the code as it doesn't seem to be used anywhere. Change-Id: I4c89fb65b2cdd26fbb0c58fccbbb4b03f0e5f1b3 Signed-off-by:
Neerav Parikh <Neerav.Parikh@intel.com> Signed-off-by:
-
Neerav Parikh authored
The allocation and clearing of rings for a VSI should be using the alloc_queue_pairs and not num_queue_pairs. The alloc_queue_pairs per VSI is a pre-allocated number of queues assigned to a VSI; based on number of TCs enabled only certain number of queues may be used from that. This is mainly valid only for the LAN VSI case as that is the only VSI that may be enabled with multiple traffic classes. In the future the number of TCs may change based on DCBX configuration. The actual number of queues that are enabled/configured is based on the number of TCs enabled for a given VSI and that is stored in num_queue_pairs. With this change num_[tr]x_queues is unused so remove them. Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29 Signed-off-by:
-
Shannon Nelson authored
Don't try to free a q_vector that hasn't been set up as it can panic the kernel. Change-Id: I0650cc6c441d0779788c522c790293c276d14fbc Signed-off-by:
Shannon Nelson <shannon.nelson@intel.com> Signed-off-by:
-
David Cassard authored
Save both a pointer to memory and the length in order to store all info about allocated kernel memory. This patch changes some adminq allocations to preserve the full i40e_dma_mem/i40e_virt_mem structs for every allocation. Change-Id: Ibcf96159aba4ba61f839d16d87d19478df28e630 Signed-off-by:
David Cassard <david.g.cassard@intel.com> Signed-off-by:
-
Shannon Nelson authored
Swap a couple lines around in the error handling if the kzalloc() for the pf->vsi array fails. This was causing a kernel BUG because the call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array existed. In this fix it is possible that i40e_reset_interrupt_capability() will get called twice, but this is a safe action. Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1 Signed-off-by:
-
Mitch Williams authored
When cleaning the ARQ, we must reinitialize the buffer size each time we go through the loop, because i40e_clean_arq_element returns the message length in the same field. Without this change, subsequent messages can be truncated to the length of the previous message. Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb Signed-off-by:
-
Mitch Williams authored
Introduce i40e_irq_dynamic_disable_icr0 and use it and its previously- extant counterpart when appropriate. Change-Id: Ieb4037874fba2e96fc2354b34a97a3cb8f6490f3 Signed-off-by:
-
Vasu Dev authored
Add an include header guard to guard against multiple includes Change-Id: I73efa03efc912d2047edab903c7caed05b444da2 Signed-off-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Mitch Williams authored
When disabling and enabling VFs on a live system with the VF driver loaded, it's possible to receive an admin queue message from the VF driver at an inconvenient time, e.g. when the associated data structures aren't present or configured. This causes a rather inconvenient panic. To guard against this, we change the order of when we set num_alloc_vfs when turning off SR-IOV, and then gate processing of any VF messages based upon that value. Likewise, when enabling VFs, we shut off the relevant interrupt until configuration is complete. Change-Id: I0c172c056616c2bebd78bbc807ab446eb484deea Signed-off-by:
-
Jesse Brandeburg authored
replace __constant_htons with htons Change-Id: I123a5318bae34c8b004c71db07c56f137c685849 Signed-off-by:
-
Anjali Singhai Jain authored
Earlier we were reading Shadow RAM (copy of the NVM) which can differ from the actual NVM. Use AQ instead to read the actual NVM. Change-Id: Ia0f2773b722db77d093f738c068af872be69bbd4 Signed-off-by:
-
Jesse Brandeburg authored
Remove custom i40e functions around ethernet addresses that are duplicating already existing kernel functionality. Also ends up fixing a bug with multicast addresses. Signed-off-by:
-
Anjali Singhai Jain authored
Debugfs was reading exactly half the number of words, fix it. Change-Id: Ieb217f3c6dca455d44e50a0dc61a6664c0cb2265 Signed-off-by:
-
David S. Miller authored
bgmac: add initial support for core rev 4 on ARM BCM47xx ==================== This adds support for core rev 4 and ARM BCM47XX. With an other fix to the platform code I am now getting over 200 MBit/s with this Ethernet driver, the DMA problems are solved are unrelated to bgmac. v3: - moved flags calculation for bcma_core_enable() into if block - remove hard coding of phy address to BGMAC_PHY_NOREGS v2: add changed suggested by Rafał ==================== Signed-off-by: -
Hauke Mehrtens authored
This adds support for the Northstar SoC. This SoC does not have a PMU in bcma and no register on it should be called. In addition it support 2.5 GBit/s Ethernet to the PHY. This GMAC core is not fully working there are still problems with the DMA controller. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Hauke Mehrtens authored
On the Northstar SoC (BCM4707 and BCM53018) we have to enable all GMAC cores when we just want to use on. We iterate over all the cores and activate them. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Hauke Mehrtens authored
The BGMAC_CMDCFG_SR register is at a different position on core rev >= 4 We do not know where this register is on a rev 5 or higher core, I have newer seen such a core. Signed-off-by:
-
Hauke Mehrtens authored
The DMA controller used in the device supported by GMAC with core rev >= 4 has some new options which are now set to the default values used in the Broadcom SDK. Signed-off-by:
-
Hauke Mehrtens authored
This function is used to get a specific core when there is more than one core of that specific type. This is used in bgmac to reset all GMAC cores. Signed-off-by:
-
stephen hemminger authored
Remove dead code; tipc_bearer_find_interface tipc_node_redundant_links This may break out of tree version of TIPC if there still is one. But that maybe a good thing :-) Signed-off-by:Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
stephen hemminger authored
Signed-off-by:
-
stephen hemminger authored
Make DCCP module config variable static, only used in one file. Signed-off-by:
-
stephen hemminger authored
This function is defined but not used. Remove it now, can be resurrected if ever needed. Signed-off-by:
-
Li RongQing authored
They are same, so unify them as one; since macvlan is a kind of vlan, vlan_pcpu_stats should be a proper name for vlan and macvlan. Signed-off-by:
-
