- 22 Aug, 2009 31 commits
-
-
Joe Eykholt authored
libfc debug messages currently show 'lport: <fc-id>:' wher <fc-id> is the hex assigned port-id. When the lport is logged off, that will be zero, so its hard to distinguish which instance is involved. The FC-ID can change if the port is re-patched or changes VSANs. Two lports may even have the same FC-ID if connected to isolated SANs. Change the debug messages to print the SCSI host number "hostN:", which will not change for the life of the lport. Still show the FC_ID on lport messages. Also, add a macro to FC_RPORT_ID_DBG for rport debugging where there's no rdata structure involved. It takes the lport and port_id as parameters. Use this in fc_rport_recv_plogi_req() and fc_rport_recv_logo_req(). Signed-off-by:
Joe Eykholt <jeykholt@cisco.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Joe Eykholt authored
This is unlikely to cause any problems, but the libfc debug macros introduce extra undesirable semicolons. Signed-off-by:
-
Yi Zou authored
No need to check phys_dev here, just call dev_ethtool_get_settings() directly will take care of this. Signed-off-by:
Yi Zou <yi.zou@intel.com> Signed-off-by:
-
Yi Zou authored
When encap the els for FIP, set the fip_flags according to the FCF and lport's capability of supporting SPMA or FPMA or both. Signed-off-by:
-
Yi Zou authored
Fix this bug of validating the wrong mac address while checking for SAN MAC address support from LLD as we should check ha->addr not ctlr.ctl_src_addr. Signed-off-by:
-
Mike Christie authored
alua_activate only sends a STPG if only explicit is suppored. As a result, for EMC targets that support both we end up doing a implicit failover when X commands are finally sent to the other SP. This patch does a AND on the h->tpgs, so we do a explicit failover right away. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
James Bottomley authored
There are two setup places for max_phys in scsi_transport_sas.c; one incorrectly places a NULL into host_attrs instead of port_attrs. Remove it. Reported-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Update driver version to 8.3.4 Signed-off-by:
-
James Smart authored
Remove spaces before newlines in several log messages Signed-off-by:
-
James Smart authored
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands This patch adds a new file, lpfc_bsg.c. Signed-off-by:
-
James Smart authored
NPIV vport fixes - Fixed static vport creation on SLI4 HBAs - Fixed vport create sending init_vpi before REG_VFI - Fix unable to create vports on SLI4 HBA's Port2 Signed-off-by:
-
James Smart authored
Fix a pair of FCoE issues - Fix Region 23 FCoE Parameters not being read correctly - Fix race condition when there are FCoE events during FCF table read Signed-off-by:
-
James Smart authored
Various SLI3 fixes - Fix for firmware dump failure - Fix inband remote management Signed-off-by:
-
James Smart authored
Consistently implement persistent port disable. Ability was to be managed in the adapter via firmware via flash settings. However, not all firmware images supported it. Uniformly support it everywhere. Signed-off-by:
-
James Smart authored
Various SLI4 fixes - Fix switch name not used in the FCF record for FCoE HBAs - Enabled HBA UE error polling error-condition action code - Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly - Modify resume_rpi mailbox data structure to match current SLI4 spec - Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set - Wait for HBA POST completion before checking Online and UE registers - Fix accumulated total length not being filled in on unsolicited IOCBs - Use PCI config space register to determine SLI rev of HBA - Turn on starting ELS tmo function timer during device initialization Signed-off-by:
-
Johannes Berg authored
print_mac is being deprecated, and %pM makes for smaller code anyway. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Acked-by:
-
Jiri Slaby authored
When kzalloc fails in lpfc_hba_alloc, don't dereference the NULL by lpfc_printf_log. Use dev_err instead. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Acked-By:
-
Dave Jones authored
On ppc64, gcc 4.4 spews lots of.. drivers/scsi/qla2xxx/qla_def.h:1485:7: warning: "__LITTLE_ENDIAN" is not defined Signed-off-by:
Dave Jones <davej@redhat.com> Signed-off-by:
-
Anil Veerabhadrappa authored
When using iface, bnx2i was unable to offload further connections after all active sessions are logged out. bnx2i will unregister the device from cnic when the last connection is torn down. Next call to ep_connect() will fail because the device is not registered. This issue is not seen if shost == NULL is passed to ep_connect() call because in that case bnx2i will registers all known devices with cnic before doing a route look-up. When shost != NULL, bnx2i knows the device on which to offload the connection and has to register this device before attempting to offload the connection Signed-off-by:
Anil Veerabhadrappa <anilgv@broadcom.com> Reviewed-by:
Michael Chan <mchan@broadcom.com> Reviewed-by Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Randy Dunlap authored
Change function parameter name in kernel-doc to match the function's actual parameter name, to fix 2 kernel-doc warnings. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Anil Veerabhadrappa authored
convert bnx2i_dev_lock to type mutex from rwlock_t because cnic->register_device() can sleep for various reasons including memory allocation, waiting for ISCSI_INIT completion and while acquiring mutex lock, cnic_lock. Signed-off-by:
-
Anil Veerabhadrappa authored
Fixed bnx2i_init_one() to properly handle return code of cnic->register_device() and propagate it back to the caller. No need to check for BNX2I_CNIC_REGISTERED, because unless the adapter is added to adapter_list it will not be registered in ep_connect context Signed-off-by:
-
Anil Veerabhadrappa authored
Removed bnx2i_reg_devices as this counter is not really used in a meaningful way Signed-off-by:
-
Martin K. Petersen authored
When a request fails we print the sense data but not the actual command that failed. Add a printout of the operation + CDB for failed commands. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Chandra Seetharaman authored
Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2 scsi_dh does not do a refernce count for attach/detach, and this affects the way it is supposed to work with multipath when a device is not in the dev_list of the hardware handler. This patch adds a reference count that counts each attach. Signed-off-by:
Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by:
-
Douglas Gilbert authored
It has been 3 years since this file was sync-ed with www.t10.org . Information taken from the last bunch of drafts released in May 2009. More asc/ascq codes are coming for thin provisioning; when approved and allocated another patch could add them prior to this patch going live. Changelog: - add some new command names and rename two commands - sync asc/ascq table with www.t10.org/lists/asc-num.txt - correct bug in scsi_extd_sense_format() [second for loop] Signed-off-by:Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: check saved state before restore
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] mpt2sas: fix config request and diag reset deadlock [SCSI] mpt2sas: Bump driver version 01.100.04.00 [SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate [SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode [SCSI] mpt2sas: fix infinite loop inside config request [SCSI] mpt2sas: Excessive log info causes sas iounit page time out [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages [SCSI] mpt2sas: Expander fix oops saying "Already part of another port" [SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash
-
Linus Torvalds authored
-
Linus Torvalds authored
In commit a8e7d49a ("Fix race in create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test for a NULL page mapping unintentionally when some of the code inside __set_page_dirty() was moved to the callers. That removal generally didn't matter, since a filesystem would serialize truncation (which clears the page mapping) against writing (which marks the buffer dirty), so locking at a higher level (either per-page or an inode at a time) should mean that the buffer page would be stable. And indeed, nothing bad seemed to happen. Except it turns out that apparently reiserfs does something odd when under load and writing out the journal, and we have a number of bugzilla entries that look similar: http://bugzilla.kernel.org/show_bug.cgi?id=13556 http://bugzilla.kernel.org/show_bug.cgi?id=13756 http://bugzilla.kernel.org/show_bug.cgi?id=13876 and it looks like reiserfs depended on that check (the common theme seems to be "data=journal", and a journal writeback during a truncate). I suspect reiserfs should have some additional locking, but in the meantime this should get us back to the pre-2.6.29 behavior. Pattern-pointed-out-by:
Roland Kletzing <devzero@web.de> Cc: stable@kernel.org (2.6.29 and 2.6.30) Cc: Jeff Mahoney <jeffm@suse.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 21 Aug, 2009 9 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/radeon: add GET_PARAM/INFO support for Z pipes drm/radeon/kms: add r100/r200 OQ support. drm: Fix sysfs device confusion. drm/radeon/kms: implement the bo busy ioctl properly.
-
git://git.kernel.dk/linux-2.6-blockLinus Torvalds authored
* 'btrfs' of git://git.kernel.dk/linux-2.6-block: btrfs: fix inode rbtree corruption
-
Linus Torvalds authored
As noted in 83d349f3 ("x86: don't send an IPI to the empty set of CPU's"), some APIC's will be very unhappy with an empty destination mask. That commit added a WARN_ON() for that case, and avoided the resulting problem, but didn't fix the underlying reason for why those empty mask cases happened. This fixes that, by checking the result of 'cpumask_andnot()' of the current CPU actually has any other CPU's left in the set of CPU's to be sent a TLB flush, and not calling down to the IPI code if the mask is empty. The reason this started happening at all is that we started passing just the CPU mask pointers around in commit 4595f962 ("x86: change flush_tlb_others to take a const struct cpumask"), and when we did that, the cpumask was no longer thread-local. Before that commit, flush_tlb_mm() used to create it's own copy of 'mm->cpu_vm_mask' and pass that copy down to the low-level flush routines after having tested that it was not empty. But after changing it to just pass down the CPU mask pointer, the lower level TLB flush routines would now get a pointer to that 'mm->cpu_vm_mask', and that could still change - and become empty - after the test due to other CPU's having flushed their own TLB's. See http://bugzilla.kernel.org/show_bug.cgi?id=13933 for details. Tested-by:
Thomas Björnell <thomas.bjornell@gmail.com> Cc: stable@kernel.org Signed-off-by:
-
Linus Torvalds authored
When 'and'ing two bitmasks (where 'andnot' is a variation on it), some cases want to know whether the result is the empty set or not. In particular, the TLB IPI sending code wants to do cpumask operations and determine if there are any CPU's left in the final set. So this just makes the bitmask (and cpumask) functions return a boolean for whether the result has any bits set. Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix) Signed-off-by: -
Linus Torvalds authored
The default_send_IPI_mask_logical() function uses the "flat" APIC mode to send an IPI to a set of CPU's at once, but if that set happens to be empty, some older local APIC's will apparently be rather unhappy. So just warn if a caller gives us an empty mask, and ignore it. This fixes a regression in 2.6.30.x, due to commit 4595f962 ("x86: change flush_tlb_others to take a const struct cpumask"), documented here: http://bugzilla.kernel.org/show_bug.cgi?id=13933 which causes a silent lock-up. It only seems to happen on PPro, P2, P3 and Athlon XP cores. Most developers sadly (or not so sadly, if you're a developer..) have more modern CPU's. Also, on x86-64 we don't use the flat APIC mode, so it would never trigger there even if the APIC didn't like sending an empty IPI mask. Reported-by:
Pavel Vilim <wylda@volny.cz> Reported-and-tested-by:
Martin Rogge <marogge@onlinehome.de> Cc: Mike Travis <travis@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: stable@kernel.org Signed-off-by:
-
Alex Deucher authored
Needed for occlusion queries on rv530 chips. Signed-off-by:
Alex Deucher <alexdeucher@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
From: Nick Piggin authored
Node may not be inserted over existing node. This causes inode tree corruption and I was seeing crashes in inode_tree_del which I can not reproduce after this patch. The other way to fix this would be to tie inode lifetime in the rbtree with inode while not in freeing state. I had a look at this but it is not so trivial at this point. At least this patch gets things working again. Signed-off-by:
Nick Piggin <npiggin@suse.de> Cc: Chris Mason <chris.mason@oracle.com> Acked-by:
Yan Zheng <zheng.yan@oracle.com> Signed-off-by:
Jens Axboe <jens.axboe@oracle.com>
-
Dave Airlie authored
This adds the relocation necessary for OQ support on the r100/r200 chipsets. Signed-off-by: -
Thomas Hellstrom authored
The drm sysfs class suspend / resume methods could not distinguish between different device types wich could lead to illegal type casts. Use struct device_type and make sure the class suspend / resume callbacks are aware of those. There is no per device-type suspend / resume. Only new-style PM. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
