- 18 Aug, 2017 38 commits
-
-
Lendacky, Thomas authored
Add per queue Tx and Rx packet and byte counts. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Use the dynamic debug support to output information about the hardware features reported by the device. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Currently whenever the driver needs to enable or disable interrupts for a DMA channel it reads the interrupt enable register (IER), updates the value and then writes the new value back to the IER. Since the hardware does not change the IER, software can track this value and elimiate the need to read it each time. Add the IER value to the channel related data structure and use that as the base for enabling and disabling interrupts, thus removing the need for the MMIO read. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Add some additional dynamic debug message to the driver. The new messages will provide additional information about the PCS window calculation. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Many of the names used by the driver are based upon the name of the device found during device probe. Move the formatting of the names into the device open function so that any renaming that occurs before the device is brought up will be accounted for. This also means moving the creation of some named workqueues into the device open path. Add support to register for net events so that if a device is renamed the corresponding debugfs directory can be renamed. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
When transmitting a TSO packet, the driver only increments the TSO packet statistic by one rather than the number of total packets that were sent. Update the driver to record the total number of packets that resulted from TSO transmit. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Sometimes when the driver is being unloaded while the devices are still up the driver can issue errors. This is based on timing and the double invocation of some routines. The phy_exit() call needs to be run after the network device has been closed and unregistered from the system. Also, the phy_exit() does not need to invoke phy_stop() since that will be called as part of the device closing, so remove that call. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
When running in SGMII mode at speeds below 1000Mbps, the auto-negotition control register must set the MII control width for the MAC interface to be 8-bits wide. By default the width is 4-bits. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
Currently the MDIO mode is set to none for the 10000Base-T, which is incorrect. The MDIO mode should for this configuration should be clause 45. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
Currently, if vport is zero then then an uninialized return status in err is returned. Since the only return status at the end of the function esw_add_uc_addr is zero for the current set of return paths we may as well just return 0 rather than err to fix this issue. Detected by CoverityScan, CID#1452698 ("Uninitialized scalar variable") Fixes: eeb66cdb ("net/mlx5: Separate between E-Switch and MPFS") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Martin KaFai Lau authored
In check_map_func_compatibility(), a 'break' has been accidentally removed for the BPF_MAP_TYPE_ARRAY_OF_MAPS and BPF_MAP_TYPE_HASH_OF_MAPS cases. This patch adds it back. Fixes: 174a79ff ("bpf: sockmap with sk redirect support") Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Jesper Dangaard Brouer says: ==================== xdp: adjust xdp redirect tracepoint Working on streamlining the tracepoints for XDP. The eBPF programs and XDP have no flow-control or queueing. Investigating using tracepoint to provide a feedback on XDP_REDIRECT xmit overflow events. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
The return error code need to be included in the tracepoint xdp:xdp_redirect, else its not possible to distinguish successful or failed XDP_REDIRECT transmits. XDP have no queuing mechanism. Thus, it is fairly easily to overrun a NIC transmit queue. The eBPF program invoking helpers (bpf_redirect or bpf_redirect_map) to redirect a packet doesn't get any feedback whether the packet was actually transmitted. Info on failed transmits in the tracepoint xdp:xdp_redirect, is interesting as this opens for providing a feedback-loop to the receiving XDP program. Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
Use errno -ENOSPC ("No space left on device") when the XDP xmit have no space left on the TX ring buffer, instead of -ENOMEM. Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rick Farrington authored
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Levin, Alexander (Sasha Levin) authored
This is useful for directly looking up a task based on class id rather than having to scan through all open file descriptors. Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dimitris Michailidis authored
Currently macvlan devices do not set their hw_enc_features making encapsulated Tx packets resort to SW fallbacks. Add encapsulation GSO offloads to ->features as is done for the other GSOs and set ->hw_enc_features. Signed-off-by: Dimitris Michailidis <dmichail@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Intiyaz Basha authored
Fix Smatch error by not dereferencing iq pointer if it's NULL. See http://marc.info/?l=kernel-janitors&m=150296723301129&w=2 Also, remove unnecessary parentheses. Fixes: d314ac22 ("liquidio: moved liquidio_napi_poll to lio_core.c") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
refcount_t type and corresponding API should be used instead of atomic_t when the variable is used as a reference counter. This allows to avoid accidental refcounter overflows that might lead to use-after-free situations. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2017-08-18 Here's one more bluetooth-next pull request for the 4.14 kernel: - Multiple fixes for Broadcom controllers - Fixes to the bluecard HCI driver - New USB ID for Realtek RTL8723BE controller - Fix static analyzer warning with kfree Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
Adding a lock around one of the assignments prevents gcc from tracking the state of the local 'fibmatch' variable, so it can no longer prove that 'dst' is always initialized, leading to a bogus warning: net/ipv6/route.c: In function 'inet6_rtm_getroute': net/ipv6/route.c:3659:2: error: 'dst' may be used uninitialized in this function [-Werror=maybe-uninitialized] This moves the other assignment into the same lock to shut up the warning. Fixes: 121622db ("ipv6: route: make rtm_getroute not assume rtnl is locked") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Salil Mehta says: ==================== Misc. Bug fixes for HNS3 Ethernet Driver This patch-set fixes various bugs reported by community. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Salil authored
This patch fixes the static check warning due to missing handling leg of unsupported L3 protocol type in the hns3_get_l4_protocol() function. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Salil authored
This patch fixes the static check error warning in hns3_get_link_ksettings() function by re-arranging the code. Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 Driver") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Salil authored
This patch fixes the missing u64_stats_fetch_begin_irq() while trying to atomically do 64-bit RX/TX fetch. We did not get any error during test as our SoC is 64-bit so all of these seq/lock operations results in NOOP. As such, this seq lock supports has been added for the sake of completion if this code ever runs on 32-bit platform and we are trying to do 64-bit stats fetch. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Chris Mi authored
The offending commit used a newly added helper function. But the logic is wrong. Without this fix, the affected NICs can't do HW offload. Error -EOPNOTSUPP will be returned directly. Fixes: a2e8da93 ("net/sched: use newly added classid identity helpers") Signed-off-by: Chris Mi <chrism@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/net: more updates for 4.14 please apply another batch of qeth patches for net-next. This reworks the xmit path for L2 OSAs to use skb_cow_head() instead of skb_realloc_headroom(). ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
Taking a full copy via skb_realloc_headroom() on every xmit is overkill and wastes CPU time; all we actually need is to push on the qeth_hdr. So rework the L2 OSA TX path to avoid the copy. Minor complications arise because struct qeth_hdr must not cross a page boundary. So add a new helper qeth_push_hdr() that catches this, and falls back to the hdr cache that we already use for IQDs. This change uncovered that qeth's TX completion takes rather long. Now that we no longer free the original skb straight away and thus call skb->destructor later than before, throughput regresses significantly. For now, restore old behaviour by adding an explicit skb_orphan(), and a big TODO to improve the TX completion time. Tested-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
After plenty of refactoring, use hd_len as single indication that the skb needs a dedicated header element. This preserves existing behaviour for TSO, as 'hdr' always points to skb->data. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
This is a prerequisite for unifying the code to build header elements. The TSO header has a different size, so we can no longer rely on implicitly adding the size of a normal qeth_hdr. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping it into buffer elements. Instead of (mis)using skb_pull(), pass a corresponding offset to fill_buffer() like we already do for IQDs. No actual change in the resulting TSO buffers. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
The TSO code already calculates the length of its header element, no need to duplicate this in the low-level code again. Use this opportunity to make hd_len unsigned, and for TSO match its calculation to what tso_fill_header() does. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
For IQD we already need to fix up the qeth_hdr's length field, and future changes will require more flexibility for OSA as well. The device-specific path knows best what header length it requires, so just pass it from there. While at it, remove the unused qeth_card parameter. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julian Wiedmann authored
l2_hard_start_xmit() actually doesn't contain much shared code, and having device-specific paths makes isolated changes a lot easier. So split it into three routines for IQD, OSN and OSD/OSM/OSX. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
"map" is a valid pointer. We wanted to return "err" instead. Also let's return a zero literal at the end. Fixes: 174a79ff ("bpf: sockmap with sk redirect support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Rick Farrington says: ==================== liquidio: initialization fixes for embedded firmware Fix problems when using an adapter w/embedded f/w (param "fw_type=none"). 1. Add support for PF FLR when exiting. 2. Skip some initialization (don't try to load f/w, activate consoles). 3. Issue credits BEFORE enabling DROQs. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rick Farrington authored
1. Issue credits BEFORE enabling DROQ's; this prevents PKTPF_ERR interrupt. Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rick Farrington authored
1. Add support for PF FLR when exiting (enables CORE_DRV_ACTIVE upon next driver init) 2. Skip some initialization (don't try to load f/w, activate consoles). Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 17 Aug, 2017 2 commits
-
-
Marcel Holtmann authored
The Broadcom controller on the Raspberry Pi3 sends an empty packet with packet type 0x00 after launching the firmware. This will cause logging of errors. Bluetooth: hci0: Frame reassembly failed (-84) Since this seems to be an intented behaviour of the controller, handle it gracefully by parsing that empty packet with packet type 0x00 and then just simply report it as diagnostic packet. With that change no errors are logging and the packet itself is actually recorded in the Bluetooth monitor traces. < HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4 Address: 0xffffffff > HCI Event: Command Complete (0x0e) plen 4 Broadcom Launch RAM (0x3f|0x004e) ncmd 1 Status: Success (0x00) = Vendor Diagnostic (len 0) < HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6 00 00 00 10 0e 00 ...... > HCI Event: Command Complete (0x0e) plen 4 Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1 Status: Success (0x00) < HCI Command: Reset (0x03|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Reset (0x03|0x0003) ncmd 1 Status: Success (0x00) Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Loic Poulain authored
Add binding document for serial bluetooth chips using Broadcom protocol. Signed-off-by: Loic Poulain <loic.poulain@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-