Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The number of chainmasks for AR9285 weren't being
setup when running NF calibration.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Dual stream capability must be registered only when the
hardware supports it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR9285 based devices support only single stream MCS rates.
This patch fixes a bug where dual stream stream rates were
also being registered.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds an ath9k specific entry to read, write and reset the TSF into the debugfs, like in ath5k. This makes debugging the IBSS handling of wifi drivers _much_ easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates the ath5k specific entry in the debugfs to read and reset the TSF value, to allowing write it, too. This makes debugging the IBSS handling of wifi drivers _much_ easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds an low-level driver independent entry to read the TSF value into the debugfs of mac80211. This makes debugging the IBSS handling of wifi drivers easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.

Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().

If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Let users be more compliant if so desired.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a driver is given a wiphy and it wants to get to its private
mac80211 driver area it can use wiphy_to_ieee80211_hw() to get first
to its ieee80211_hw and then access the private structure via hw->priv. The
wiphy_priv() is already being used internally by mac80211 and drivers
should not use this. This can be helpful in a drivers reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows drivers to request strict regulatory settings to
be applied to its devices. This is desirable for devices where
proper calibration and compliance can only be gauranteed for
for the device's programmed regulatory domain. Regulatory
domain settings will be ignored until the device's own
regulatory domain is properly configured. If no regulatory
domain is received only the world regulatory domain will be
applied -- if OLD_REG (default to "US") is not enabled. If
OLD_REG behaviour is not acceptable to drivers they must
update their wiphy with a custom reuglatory prior to wiphy
registration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers may need more information than just who set the last regulatory domain,
as such lets just pass the last regulatory_request receipt. To do this we need
to move out to headers struct regulatory_request, and enum environment_cap. While
at it lets add documentation for enum environment_cap.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This ensures that the initial REGDOM_SET_BY_CORE upon wiphy registration
respects the wiphy->custom_regulatory setting. Without this and if OLD_REG
is disabled (which will be default soon as we remove it) the
wiphy->custom_regulatory is simply ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers without firmware can also have custom regulatory maps
which do not map to a specific ISO / IEC alpha2 country code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We ignore regulatory hints for the same alpha2 if we already
have processed the same alpha2 on the current regulatory domain.
For a driver regulatory_hint() this means we copy onto its
wiphy->regd the previously procesed regulatory domain from CRDA
without having to call CRDA again.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This prevents user regulatory changes to be considered prior to previous
pending user, core or driver requests which have not be applied.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This can be used by drivers on the reg_notifier()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds wiphy_apply_custom_regulatory() to be used by drivers
prior to wiphy registration to apply a custom regulatory domain.
This can be used by drivers that do not have a direct 1-1 mapping
between a regulatory domain and a country.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a flag to notify drivers to start and stop
beaconing when needed, for example, during a scan run. Based
on Sujith's first patch to do the same, but now disables
beaconing for all virtual interfaces while scanning, has a
separate change flag and tracks user-space requests.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ath5k driver didn't use set_rts_threshold or use_cts_prot, and also
didn't check the IEEE80211_TX_RC_USE_{RTS_CTS,CTS_PROTECT} RC flags.
Tell the hardware about these so RTS/CTS will work, and so the device
will work better in mixed b/g environments.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k previously ignored TX_RC_SHORT_PREAMBLE and did not use
config->use_short_preamble, so the long preamble was always
used for transmitted packets.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k_softc->led_off hasn't been used since commit
3a078876, "convert LED code to use
mac80211 triggers."

Changes-licensed-under: 3-Clause-BSD
Reported-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove extra space; remove redundant cast
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No functional changes; use new kernel interface for netdev methods.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Then one place can be a static const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A warning message "MAC is in deep sleep" sometimes happen when user removes
the driver.  This warning is related to card not being ready. In __iwl3945_down
function some of the going down steps are in wrong order, to fix this this patch
do the following:
	1- make sure we are calling iwl3945_apm_reset and iwl3945_apm_stop
	   in the right order.

	2- make sure we set CSR_GP_CNTRL_REG_FLAG_INIT_DONE in apm_reset before
	   poll on CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY.

	3- set correct polling counter.

This fixes bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1834Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Here again, the rfkill routines are duplicated between agn and 3945. Let's
move the agn one to iwlcore, and so we can get rid of the 3945 ones.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sometime Tx reply rate different than what rate scale expecting
causing rate scale to bail out. This could cause failing to
commit LQ cmd. This patch will try to solve this instead of just
bail out. It also make sure we start with a valid rate.
Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

allow user to set max rate through #iwconfig <inteface> rate XXX.
mac80211 will try to force this if user set it, but driver is not
in sync which cause mac80211 to report wrong current rate. This
patch will check if max rate is set and force it in rate scaling
Signed-off-by: mohamed abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch implements dynamic power save feature for ath9k.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add configuration for new Intel WiFi Link 100 series as part of the
iwlagn driver under the umbrella of 5000 family of devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add configuration for new Intel WiFi Link Series as part of the iwlagn
driver under the umbrella of 5000 family of devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

remove static from config structures which will be used by new
hardware that is similar to 5000.  This way the new devices
can use them without the new structures having to be stored in the
already overloaded iwl-5000.c file.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

    defining configurations that are not visible caused the following
    entries to not be indented. changing the tree structure to name the
    top level selection and have all others reference IWLWIFI directly
    corrects this issue.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch eliminates 3945 power_data structure and make use of
of iwl_power_data.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>