When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.

Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.

There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

With commit 21cc2bda (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

When booting with device-tree, retrieve GPMC settings for ONENAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.

The user must now specify the ONENAND device width in the device-tree
binding so that the GPMC can be programmed correctly. Therefore, update
the device-tree binding documentation for ONENAND devices connected to
the GPMC to reflect this.

Please note that this does not include GPMC timings for ONENAND. The
timings are being calculated at runtime.

There is some legacy code that only enables read wait monitoring for
non-OMAP3 devices. There are no known OMAP3 device issues that prevent
this feature being enabled and so when booting with device-tree use the
wait-monitoring settings described in the device-tree blob.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

When booting with device-tree, retrieve GPMC settings for NAND from
the device-tree blob. This will allow us to remove all static settings
stored in the gpmc-nand.c in the future once the migration to
device-tree is complete.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.

Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.

The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.

The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Adds a function to read the various GPMC chip-select settings from
device-tree and store them in the gpmc_settings structure.

Update the GPMC device-tree binding documentation to describe these
options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ TUSB code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ SMC91x code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.

Move configuration of the GPMC settings outside retime function and
this does not need to be done if the timings are changed dynamically
at runtime.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ NAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.

This moves the configuration of some GPMC options outside the
nand_gpmc_retime() because these options should only need to be set once
regardless of whether the gpmc timing is changing dynamically at runtime.
The programming of where the wait-pin is also moved slightly, but this
will not have any impact to existing devices as no boards are currently
setting the dev_ready variable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

Convert the OMAP2+ ONENAND code to use the gpmc_cs_program_settings()
function for configuring the various GPMC options instead of directly
programming the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.

Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.

Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.

When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

The OMAP2+ code that configures the GPMC for ONENAND devices is copying
structures between functions unnecessarily. Avoid this by passing
pointers instead and simplify the code.

A pointer to structure "omap_onenand_platform_data" is passed to the
function omap2_onenand_calc_sync_timings(), but only the flags member
of the structure is used. Simplify the code by only passing the flags
member and not the entire structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>

This check is done before the call to gpmc_cs_reserved() and
gpmc_cs_set_reserved() and it's redundant to do it again in each
function. This simplifies the code a bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Since the condition is not an error but a warning, replace
printk KERN_ERR with dev_warn.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Do this becasue dev_err() is preferred over pr_err() and because
it will match gpmc-nand, thus the code shows looks more consistent.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

If CS request fails the current error message is rather unhelpful.
Fix it by printing the failing chip select and the error code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

If CS request fails the current error message is rather unhelpful.
Fix it by printing the failing chip select and the error code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Currently gpmc_cs_reserved() return value is somewhat inconsistent,
returning a negative value on an error condition, a positive value
if the chip select is reserved and zero if it's available.

Fix this by returning a boolean value as the function name suggests:
  * true if the chip select is reserved,
  * false if it's available
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

This function is not used anywhere, so it's safe to remove it.
This means less code to maintain.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

This patch marks a bunch of functions that are local
to gpmc.c file only as static.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

When setting the GPMC device type, make sure any previous
bits are cleared down, before applying the new setting.

For OMAP4+ devices MUXADDDATA is a 2-bit field (bits 9:8)
where as for OMAP2/3 devices it was only a one bit field
(bit 9). For OMAP2/3 devices bit 8 is reserved and the
OMAP documentation says to write a 0 to this bit. So
clearing bit 8 on OMAP2/3 devices should not be a problem.
Hence update the code to handle both bits 8 and 9 for all
devices.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
[jon-hunter@ti.com: updated changelog]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>

Conflicts:
	arch/arm/plat-omap/dmtimer.c

Consistently check errors using the usual method used in the kernel
for much of its history.  For instance:

int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
{
	int div;
	div = gpmc_calc_divider(t->sync_clk);
	if (div < 0)
		return div;
static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
{
...
	return gpmc_cs_set_timings(cs, t);

.....
	ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
	if (IS_ERR_VALUE(ret))
		return ret;

So, gpmc_cs_set_timings() thinks any negative return value is an error,
but where we check that in higher levels, only a limited range are
errors...

There is only _one_ use of IS_ERR_VALUE() in arch/arm which is really
appropriate, and that is in arch/arm/include/asm/syscall.h:

static inline long syscall_get_error(struct task_struct *task,
				     struct pt_regs *regs)
{
	unsigned long error = regs->ARM_r0;
	return IS_ERR_VALUE(error) ? error : 0;
}

because this function really does have to differentiate between error
return values and addresses which look like negative numbers (eg, from
mmap()).

So, here's a patch to remove them from OMAP, except for the above.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:

arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...

This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull fbdev UAPI disintegration from David Howells:
 "You'll be glad to here that the end is nigh for the UAPI patches.
  Only the fbdev/framebuffer piece remains now that the SCSI stuff has
  gone in.

  Here are the UAPI disintegration bits for the fbdev drivers.  It
  appears that Florian hasn't had time to deal with my patch, but back
  in December he did say he didn't mind if I pushed it forward."

Yay.  No more uapi movement.  And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.

* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/video

Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - Update the Xen ACPI memory and CPU hotplug locking mechanism.
 - Fix PAT issues wherein various applications would not start
 - Fix handling of multiple MSI as AHCI now does it.
 - Fix ARM compile failures.

* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xenbus: fix compile failure on ARM with Xen enabled
  xen/pci: We don't do multiple MSI's.
  xen/pat: Disable PAT using pat_enabled value.
  xen/acpi: xen cpu hotplug minor updates
  xen/acpi: xen memory hotplug minor updates

Pull  more VFS bits from Al Viro:
 "Unfortunately, it looks like xattr series will have to wait until the
  next cycle ;-/

  This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
  etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
  more file_inode() work"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  constify path_get/path_put and fs_struct.c stuff
  fix nommu breakage in shmem.c
  cache the value of file_inode() in struct file
  9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
  9p: make sure ->lookup() adds fid to the right dentry
  9p: untangle ->lookup() a bit
  9p: double iput() in ->lookup() if d_materialise_unique() fails
  9p: v9fs_fid_add() can't fail now
  v9fs: get rid of v9fs_dentry
  9p: turn fid->dlist into hlist
  9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
  more file_inode() open-coded instances
  selinux: opened file can't have NULL or negative ->f_path.dentry

(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)

Pull btrfs fixup from Chris Mason:
 "Geert and James both sent this one in, sorry guys"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs/raid56: Add missing #include <linux/vmalloc.h>

Pull second set of s390 patches from Martin Schwidefsky:
 "The main part of this merge are Heikos uaccess patches.  Together with
  commit 09884964 ("mm: do not grow the stack vma just because of an
  overrun on preceding vma") the user string access is hopefully fixed
  for good.

  In addition some bug fixes and two cleanup patches."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/module: fix compile warning
  qdio: remove unused parameters
  s390/uaccess: fix kernel ds access for page table walk
  s390/uaccess: fix strncpy_from_user string length check
  input: disable i8042 PC Keyboard controller for s390
  s390/dis: Fix invalid array size
  s390/uaccess: remove pointless access_ok() checks
  s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
  s390/uaccess: shorten strncpy_from_user/strnlen_user
  s390/dasd: fix unresponsive device after all channel paths were lost
  s390/mm: ignore change bit for vmemmap
  s390/page table dumper: add support for change-recording override bit

Merge branch 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux

Pull second round of PARISC updates from Helge Deller:
 "The most important fix in this branch is the switch of io_setup,
  io_getevents and io_submit syscalls to use the available compat
  syscalls when running 32bit userspace on 64bit kernel.  Other than
  that it's mostly removal of compile warnings."

* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix redefinition of SET_PERSONALITY
  parisc: do not install modules when installing kernel
  parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
  parisc: check return value of down_interruptible() in hp_sdc_rtc.c
  parisc: avoid unitialized variable warning in pa_memcpy()
  parisc: remove unused variable 'compat_val'
  parisc: switch to compat_functions of io_setup, io_getevents and io_submit
  parisc: select ARCH_WANT_FRAME_POINTERS

Pull new ImgTec Meta architecture from James Hogan:
 "This adds core architecture support for Imagination's Meta processor
  cores, followed by some later miscellaneous arch/metag cleanups and
  fixes which I kept separate to ease review:

   - Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
   - A few fixes all over, particularly for symbol prefixes
   - A few privilege protection fixes
   - Several cleanups (setup.c includes, split out a lot of
     metag_ksyms.c)
   - Fix some missing exports
   - Convert hugetlb to use vm_unmapped_area()
   - Copy device tree to non-init memory
   - Provide dma_get_sgtable()"

* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
  metag: Provide dma_get_sgtable()
  metag: prom.h: remove declaration of metag_dt_memblock_reserve()
  metag: copy devicetree to non-init memory
  metag: cleanup metag_ksyms.c includes
  metag: move mm/init.c exports out of metag_ksyms.c
  metag: move usercopy.c exports out of metag_ksyms.c
  metag: move setup.c exports out of metag_ksyms.c
  metag: move kick.c exports out of metag_ksyms.c
  metag: move traps.c exports out of metag_ksyms.c
  metag: move irq enable out of irqflags.h on SMP
  genksyms: fix metag symbol prefix on crc symbols
  metag: hugetlb: convert to vm_unmapped_area()
  metag: export clear_page and copy_page
  metag: export metag_code_cache_flush_all
  metag: protect more non-MMU memory regions
  metag: make TXPRIVEXT bits explicit
  metag: kernel/setup.c: sort includes
  perf: Enable building perf tools for Meta
  metag: add boot time LNKGET/LNKSET check
  metag: add __init to metag_cache_probe()
  ...

Pull late ARM updates from Russell King:
 "Here is the late set of ARM updates for this merge window; in here is:

   - The ARM parts of the broadcast timer support, core parts merged
     through tglx's tree.  This was left over from the previous merge to
     allow the dependency on tglx's tree to be resolved.

   - A fix to the VFP code which shows up on Raspberry Pi's, as well as
     fixing the fallout from a previous commit in this area.

   - A number of smaller fixes scattered throughout the ARM tree"

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: Fix broken commit 0cc41e4a corrupting kernel messages
  ARM: fix scheduling while atomic warning in alignment handling code
  ARM: VFP: fix emulation of second VFP instruction
  ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
  ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
  ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
  ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
  ARM: 7651/1: remove unused smp_timer_broadcast #define

Pull char/misc patch from Greg Kroah-Hartman:
 "Here is one remaining patch for 3.9-rc1.  It is for the hyper-v
  drivers, and had to wait until some other patches went in through the
  x86 tree."
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Use the new infrastructure for delivering VMBUS interrupts