- 12 Feb, 2019 40 commits
-
-
Lukas Wunner authored
commit 9e528c79 upstream. There are multiple issues with bcm2835_dma_abort() (which is called on termination of a transaction): * The algorithm to abort the transaction first pauses the channel by clearing the ACTIVE flag in the CS register, then waits for the PAUSED flag to clear. Page 49 of the spec documents the latter as follows: "Indicates if the DMA is currently paused and not transferring data. This will occur if the active bit has been cleared [...]" https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf So the function is entering an infinite loop because it is waiting for PAUSED to clear which is always set due to the function having cleared the ACTIVE flag. The only thing that's saving it from itself is the upper bound of 10000 loop iterations. The code comment says that the intention is to "wait for any current AXI transfer to complete", so the author probably wanted to check the WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function accordingly. * The CS register is only read at the beginning of the function. It needs to be read again after pausing the channel and before checking for outstanding writes, otherwise writes which were issued between the register read at the beginning of the function and pausing the channel may not be waited for. * The function seeks to abort the transfer by writing 0 to the NEXTCONBK register and setting the ABORT and ACTIVE flags. Thereby, the 0 in NEXTCONBK is sought to be loaded into the CONBLK_AD register. However experimentation has shown this approach to not work: The CONBLK_AD register remains the same as before and the CS register contains 0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control block is not aborted but merely paused and it will be resumed once the next DMA transaction is started. That is absolutely not the desired behavior. A simpler approach is to set the channel's RESET flag instead. This reliably zeroes the NEXTCONBK as well as the CS register. It requires less code and only a single MMIO write. This is also what popular user space DMA drivers do, e.g.: https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c Note that the spec is contradictory whether the NEXTCONBK register is writeable at all. On the one hand, page 41 claims: "The value loaded into the NEXTCONBK register can be overwritten so that the linked list of Control Block data structures can be dynamically altered. However it is only safe to do this when the DMA is paused." On the other hand, page 40 specifies: "Only three registers in each channel's register set are directly writeable (CS, CONBLK_AD and DEBUG). The other registers (TI, SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically loaded from a Control Block data structure held in external memory." Fixes: 96286b57 ("dmaengine: Add support for BCM2835") Signed-off-by:
Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.14+ Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Florian Meier <florian.meier@koalo.de> Cc: Clive Messer <clive.m.messer@gmail.com> Cc: Matthias Reichl <hias@horus.com> Tested-by:
Stefan Wahren <stefan.wahren@i2se.com> Acked-by:
Florian Kauer <florian.kauer@koalo.de> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lukas Wunner authored
commit f7da7782 upstream. If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is enabled or "threadirqs" was passed on the command line) and if system load is sufficiently high that wakeup latency of IRQ threads degrades, SPI DMA transactions on the BCM2835 occasionally break like this: ks8851 spi0.0: SPI transfer timed out bcm2835-dma 3f007000.dma: DMA transfer could not be terminated ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed The root cause is an assumption made by the DMA driver which is documented in a code comment in bcm2835_dma_terminate_all(): /* * Stop DMA activity: we assume the callback will not be called * after bcm_dma_abort() returns (even if it does, it will see * c->desc is NULL and exit.) */ That assumption falls apart if the IRQ handler bcm2835_dma_callback() is threaded: A client may terminate a descriptor and issue a new one before the IRQ handler had a chance to run. In fact the IRQ handler may miss an *arbitrary* number of descriptors. The result is the following race condition: 1. A descriptor finishes, its interrupt is deferred to the IRQ thread. 2. A client calls dma_terminate_async() which sets channel->desc = NULL. 3. The client issues a new descriptor. Because channel->desc is NULL, bcm2835_dma_issue_pending() immediately starts the descriptor. 4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS register to acknowledge the interrupt. This clears the ACTIVE flag, so the newly issued descriptor is paused in the middle of the transaction. Because channel->desc is not NULL, the IRQ thread finalizes the descriptor and tries to start the next one. I see two possible solutions: The first is to call synchronize_irq() in bcm2835_dma_issue_pending() to wait until the IRQ thread has finished before issuing a new descriptor. The downside of this approach is unnecessary latency if clients desire rapidly terminating and re-issuing descriptors and don't have any use for an IRQ callback. (The SPI TX DMA channel is a case in point.) A better alternative is to make the IRQ thread recognize that it has missed descriptors and avoid finalizing the newly issued descriptor. So first of all, set the ACTIVE flag when acknowledging the interrupt. This keeps a newly issued descriptor running. If the descriptor was finished, the channel remains idle despite the ACTIVE flag being set. However the ACTIVE flag can then no longer be used to check whether the channel is idle, so instead check whether the register containing the current control block address is zero and finalize the current descriptor only if so. That way, there is no impact on latency and throughput if the client doesn't care for the interrupt: Only minimal additional overhead is introduced for non-cyclic descriptors as one further MMIO read is necessary per interrupt to check for idleness of the channel. Cyclic descriptors are sped up slightly by removing one MMIO write per interrupt. Fixes: 96286b57 ("dmaengine: Add support for BCM2835") Signed-off-by:
-
Vladis Dronov authored
commit 13054abb upstream. Ring buffer implementation in hid_debug_event() and hid_debug_events_read() is strange allowing lost or corrupted data. After commit 717adfda ("HID: debug: check length before copy_to_user()") it is possible to enter an infinite loop in hid_debug_events_read() by providing 0 as count, this locks up a system. Fix this by rewriting the ring buffer implementation with kfifo and simplify the code. This fixes CVE-2019-3819. v2: fix an execution logic and add a comment v3: use __set_current_state() instead of set_current_state() Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187 Cc: stable@vger.kernel.org # v4.18+ Fixes: cd667ce2 ("HID: use debugfs for events/reports dumping") Fixes: 717adfda ("HID: debug: check length before copy_to_user()") Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Reviewed-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Miklos Szeredi authored
commit 97e1532e upstream. Dereferencing req->page_descs[0] will Oops if req->max_pages is zero. Reported-by: syzbot+c1e36d30ee3416289cc0@syzkaller.appspotmail.com Tested-by: syzbot+c1e36d30ee3416289cc0@syzkaller.appspotmail.com Fixes: b2430d75 ("fuse: add per-page descriptor <offset, length> to fuse_req") Cc: <stable@vger.kernel.org> # v3.9 Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Miklos Szeredi authored
commit a2ebba82 upstream. NR_WRITEBACK_TEMP is accounted on the temporary page in the request, not the page cache page. Fixes: 8b284dc4 ("fuse: writepages: handle same page rewrites") Cc: <stable@vger.kernel.org> # v3.13 Signed-off-by:
-
Jann Horn authored
commit 9509941e upstream. Some of the pipe_buf_release() handlers seem to assume that the pipe is locked - in particular, anon_pipe_buf_release() accesses pipe->tmp_page without taking any extra locks. From a glance through the callers of pipe_buf_release(), it looks like FUSE is the only one that calls pipe_buf_release() without having the pipe locked. This bug should only lead to a memory leak, nothing terrible. Fixes: dd3bb14f ("fuse: support splice() writing to fuse device") Cc: stable@vger.kernel.org Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
-
Jeremy Soller authored
commit 89e3a568 upstream. On the System76 Darter Pro (darp5), there is a headset microphone input attached to 0x1a that does not have a jack detect. In order to get it working, the pin configuration needs to be set correctly, and the ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied. This is similar to the MIC_NO_PRESENCE fixups for some Dell laptops, except we have a separate microphone jack that is already configured correctly. Signed-off-by:
Jeremy Soller <jeremy@system76.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 35a39f98 upstream. Replace the open-codes in many places with a new common helper for performing the same thing: referring to the primary headphone pin. This eventually fixes the potentially missing headphone pin on some weird devices, too. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Kailang Yang authored
commit d561aa0a upstream. When auto_mute = no or spec->suppress_auto_mute = 1, cfg->hp_pins will lose value. Add this patch to find hp_pins value. I add fixed for ALC282 ALC225 ALC256 ALC294 and alc_default_init() alc_default_shutup(). Signed-off-by:
Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 305a0ade upstream. In the current code, the codec registration may happen both at the codec bind time and the end of the controller probe time. In a rare occasion, they race with each other, leading to Oops due to the still uninitialized card device. This patch introduces a simple flag to prevent the codec registration at the codec bind time as long as the controller probe is going on. The controller probe invokes snd_card_register() that does the whole registration task, and we don't need to register each piece beforehand. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Udo Eberhardt authored
commit 3bff2407 upstream. This patch adds the T+A VID to the generic check in order to enable native DSD support for T+A devices. This works with the new T+A USB DAC model SD3100HV and will also work with future devices which support the XMOS/Thesycon style DSD format. Signed-off-by:
Udo Eberhardt <udo.eberhardt@thesycon.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Charles Keepax authored
commit 4f2ab5e1 upstream. It is normal user behaviour to start, stop, then start a stream again without closing it. Currently this works for compressed playback streams but not capture ones. The states on a compressed capture stream go directly from OPEN to PREPARED, unlike a playback stream which moves to SETUP and waits for a write of data before moving to PREPARED. Currently however, when a stop is sent the state is set to SETUP for both types of streams. This leaves a capture stream in the situation where a new start can't be sent as that requires the state to be PREPARED and a new set_params can't be sent as that requires the state to be OPEN. The only option being to close the stream, and then reopen. Correct this issues by allowing snd_compr_drain_notify to set the state depending on the stream direction, as we already do in set_params. Fixes: 49bb6402 ("ALSA: compress_core: Add support for capture streams") Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Brian Foster authored
commit aa6ee4ab upstream. The cached writeback mapping is EOF trimmed to try and avoid races between post-eof block management and writeback that result in sending cached data to a stale location. The cached mapping is currently trimmed on the validation check, which leaves a race window between the time the mapping is cached and when it is trimmed against the current inode size. For example, if a new mapping is cached by delalloc conversion on a blocksize == page size fs, we could cycle various locks, perform memory allocations, etc. in the writeback codepath before the associated mapping is eventually trimmed to i_size. This leaves enough time for a post-eof truncate and file append before the cached mapping is trimmed. The former event essentially invalidates a range of the cached mapping and the latter bumps the inode size such the trim on the next writepage event won't trim all of the invalid blocks. fstest generic/464 reproduces this scenario occasionally and causes a lost writeback and stale delalloc blocks warning on inode inactivation. To work around this problem, trim the cached writeback mapping as soon as it is cached in addition to on subsequent validation checks. This is a minor tweak to tighten the race window as much as possible until a proper invalidation mechanism is available. Fixes: 40214d12 ("xfs: trim writepage mapping to within eof") Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Allison Henderson <allison.henderson@oracle.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Raed Salem authored
[ Upstream commit 82eaa1fa ] At Innova IPsec TX offload data path a special software parser metadata is used to pass some packet attributes to the hardware, this metadata is passed using the Ethernet control segment of a WQE (a HW descriptor) header. The cited commit might nullify this header, hence the metadata is lost, this caused a significant performance drop during hw offloading operation. Fix by restoring the metadata at the Ethernet control segment in case it was nullified. Fixes: 37fdffb2 ("net/mlx5: WQ, fixes for fragmented WQ buffers API") Signed-off-by:
Raed Salem <raeds@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Toshiaki Makita authored
[ Upstream commit 546f2897 ] Previously virtnet_xdp_xmit() did not account for device tx counters, which caused confusions. To be consistent with SKBs, account them on freeing xdp_frames. Reported-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 294c149a ] The "p" buffer is 0x4000 bytes long. B3_RI_WTO_R1 is 0x190. The value of "regs->len" is in the 1-0x4000 range. The bug here is that "regs->len - B3_RI_WTO_R1" can be a negative value which would lead to memory corruption and an abrupt crash. Fixes: c3f8be96 ("[PATCH] skge: expand ethtool debug register dump") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Greg Kroah-Hartman authored
[ Upstream commit ba59fb02 ] In sctp_sendmesg(), when walking the list of endpoint associations, the association can be dropped from the list, making the list corrupt. Properly handle this by using list_for_each_entry_safe() Fixes: 49102805 ("sctp: add support for snd flag SCTP_SENDALL process in sendmsg") Reported-by:
Secunia Research <vuln@secunia.com> Tested-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit cfe4bd7a ] Now when using stream reconfig to add out streams, stream->out will get re-allocated, and all old streams' information will be copied to the new ones and the old ones will be freed. So without stream->out_curr updated, next time when trying to send from stream->out_curr stream, a panic would be caused. This patch is to check and update stream->out_curr when allocating stream_out. v1->v2: - define fa_index() to get elem index from stream->out_curr. v2->v3: - repost with no change. Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations") Reported-by:
Ying Xu <yinxu@redhat.com> Reported-by: syzbot+e33a3a138267ca119c7d@syzkaller.appspotmail.com Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
-
Eric Dumazet authored
[ Upstream commit 6dce3c20 ] When either "goto wait_interrupted;" or "goto wait_error;" paths are taken, socket lock has already been released. This patch fixes following syzbot splat : WARNING: bad unlock balance detected! 5.0.0-rc4+ #59 Not tainted ------------------------------------- syz-executor223/8256 is trying to release lock (sk_lock-AF_RXRPC) at: [<ffffffff86651353>] rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598 but there are no more locks to release! other info that might help us debug this: 1 lock held by syz-executor223/8256: #0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: spin_lock_bh include/linux/spinlock.h:334 [inline] #0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2798 stack backtrace: CPU: 1 PID: 8256 Comm: syz-executor223 Not tainted 5.0.0-rc4+ #59 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_unlock_imbalance_bug kernel/locking/lockdep.c:3391 [inline] print_unlock_imbalance_bug.cold+0x114/0x123 kernel/locking/lockdep.c:3368 __lock_release kernel/locking/lockdep.c:3601 [inline] lock_release+0x67e/0xa00 kernel/locking/lockdep.c:3860 sock_release_ownership include/net/sock.h:1471 [inline] release_sock+0x183/0x1c0 net/core/sock.c:2808 rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598 sock_recvmsg_nosec net/socket.c:794 [inline] sock_recvmsg net/socket.c:801 [inline] sock_recvmsg+0xd0/0x110 net/socket.c:797 __sys_recvfrom+0x1ff/0x350 net/socket.c:1845 __do_sys_recvfrom net/socket.c:1863 [inline] __se_sys_recvfrom net/socket.c:1859 [inline] __x64_sys_recvfrom+0xe1/0x1a0 net/socket.c:1859 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x446379 Code: e8 2c b3 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 2b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fe5da89fd98 EFLAGS: 00000246 ORIG_RAX: 000000000000002d RAX: ffffffffffffffda RBX: 00000000006dbc28 RCX: 0000000000446379 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 00000000006dbc20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006dbc2c R13: 0000000000000000 R14: 0000000000000000 R15: 20c49ba5e353f7cf Fixes: 248f219c ("rxrpc: Rewrite the data and ack handling code") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: David Howells <dhowells@redhat.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Russell King authored
[ Upstream commit c14f07c6 ] This reverts commit 6623c0fb. The original diagnosis was incorrect: it appears that the NIC had PHY polling mode enabled, which meant that it overwrote the PHYs advertisement register during negotiation. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Tested-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 6fa19f56 ] syzbot was able to catch a bug in rds [1] The issue here is that the socket might be found in a hash table but that its refcount has already be set to 0 by another cpu. We need to use refcount_inc_not_zero() to be safe here. [1] refcount_t: increment on 0; use-after-free. WARNING: CPU: 1 PID: 23129 at lib/refcount.c:153 refcount_inc_checked lib/refcount.c:153 [inline] WARNING: CPU: 1 PID: 23129 at lib/refcount.c:153 refcount_inc_checked+0x61/0x70 lib/refcount.c:151 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 23129 Comm: syz-executor3 Not tainted 5.0.0-rc4+ #53 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1db/0x2d0 lib/dump_stack.c:113 panic+0x2cb/0x65c kernel/panic.c:214 __warn.cold+0x20/0x48 kernel/panic.c:571 report_bug+0x263/0x2b0 lib/bug.c:186 fixup_bug arch/x86/kernel/traps.c:178 [inline] fixup_bug arch/x86/kernel/traps.c:173 [inline] do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973 RIP: 0010:refcount_inc_checked lib/refcount.c:153 [inline] RIP: 0010:refcount_inc_checked+0x61/0x70 lib/refcount.c:151 Code: 1d 51 63 c8 06 31 ff 89 de e8 eb 1b f2 fd 84 db 75 dd e8 a2 1a f2 fd 48 c7 c7 60 9f 81 88 c6 05 31 63 c8 06 01 e8 af 65 bb fd <0f> 0b eb c1 90 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 54 49 RSP: 0018:ffff8880a0cbf1e8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffc90006113000 RDX: 000000000001047d RSI: ffffffff81685776 RDI: 0000000000000005 RBP: ffff8880a0cbf1f8 R08: ffff888097c9e100 R09: ffffed1015ce5021 R10: ffffed1015ce5020 R11: ffff8880ae728107 R12: ffff8880723c20c0 R13: ffff8880723c24b0 R14: dffffc0000000000 R15: ffffed1014197e64 sock_hold include/net/sock.h:647 [inline] rds_sock_addref+0x19/0x20 net/rds/af_rds.c:675 rds_find_bound+0x97c/0x1080 net/rds/bind.c:82 rds_recv_incoming+0x3be/0x1430 net/rds/recv.c:362 rds_loop_xmit+0xf3/0x2a0 net/rds/loop.c:96 rds_send_xmit+0x1355/0x2a10 net/rds/send.c:355 rds_sendmsg+0x323c/0x44e0 net/rds/send.c:1368 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg+0xdd/0x130 net/socket.c:631 __sys_sendto+0x387/0x5f0 net/socket.c:1788 __do_sys_sendto net/socket.c:1800 [inline] __se_sys_sendto net/socket.c:1796 [inline] __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1796 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458089 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fc266df8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000006 RCX: 0000000000458089 RDX: 0000000000000000 RSI: 00000000204b3fff RDI: 0000000000000005 RBP: 000000000073bf00 R08: 00000000202b4000 R09: 0000000000000010 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc266df96d4 R13: 00000000004c56e4 R14: 00000000004d94a8 R15: 00000000ffffffff Fixes: cc4dfb7f ("rds: fix two RCU related problems") Signed-off-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 8dfb8d2c ] Broadcom STB chips support a deep sleep mode where all register contents are lost. Because we were stashing the MagicPacket password into some of these registers a suspend into that deep sleep then a resumption would not lead to being able to wake-up from MagicPacket with password again. Fix this by keeping a software copy of the password and program it during suspend. Fixes: 83e82f4c ("net: systemport: add Wake-on-LAN support") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Cong Wang authored
[ Upstream commit e8c8b53c ] When an ethernet frame is padded to meet the minimum ethernet frame size, the padding octets are not covered by the hardware checksum. Fortunately the padding octets are usually zero's, which don't affect checksum. However, we have a switch which pads non-zero octets, this causes kernel hardware checksum fault repeatedly. Prior to: commit '88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")' skb checksum was forced to be CHECKSUM_NONE when padding is detected. After it, we need to keep skb->csum updated, like what we do for RXFCS. However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP headers, it is not worthy the effort as the packets are so small that CHECKSUM_COMPLETE can't save anything. Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), Cc: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Rundong Ge authored
[ Upstream commit 17ab4f61 ] The unbalance of master's promiscuity or allmulti will happen after ifdown and ifup a slave interface which is in a bridge. When we ifdown a slave interface , both the 'dsa_slave_close' and 'dsa_slave_change_rx_flags' will clear the master's flags. The flags of master will be decrease twice. In the other hand, if we ifup the slave interface again, since the slave's flags were cleared the 'dsa_slave_open' won't set the master's flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if' will set the master's flags. The flags of master is increase once. Only propagating flag changes when a slave interface is up makes sure this does not happen. The 'vlan_dev_change_rx_flags' had the same problem and was fixed, and changes here follows that fix. Fixes: 91da11f8 ("net: Distributed Switch Architecture protocol support") Signed-off-by:
Rundong Ge <rdong.ge@gmail.com> Signed-off-by:
-
Andrew Lunn authored
[ Upstream commit 75c05a74 ] The ATU port vector contains a bit per port of the switch. The code wrongly used it as a port number, and incremented a port counter. This resulted in the wrong interfaces counter being incremented, and potentially going off the end of the array of ports. Fix this by using the source port ID for the violation, which really is a port number. Reported-by:
Chris Healy <Chris.Healy@zii.aero> Tested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 00670cb8 ] This function can't succeed if dp->pl is NULL. It will Oops inside the call to return phylink_ethtool_get_eee(dp->pl, e); Fixes: 1be52e97 ("dsa: slave: eee: Allow ports to use phylink") Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
Marc Zyngier authored
[ Upstream commit c8101f77 ] Creating a macvtap on a DSA-backed interface results in the following splat when lockdep is enabled: [ 19.638080] IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready [ 23.041198] device lan0 entered promiscuous mode [ 23.043445] device eth0 entered promiscuous mode [ 23.049255] [ 23.049557] ============================================ [ 23.055021] WARNING: possible recursive locking detected [ 23.060490] 5.0.0-rc3-00013-g56c857a1b8d3 #118 Not tainted [ 23.066132] -------------------------------------------- [ 23.071598] ip/2861 is trying to acquire lock: [ 23.076171] 00000000f61990cb (_xmit_ETHER){+...}, at: dev_set_rx_mode+0x1c/0x38 [ 23.083693] [ 23.083693] but task is already holding lock: [ 23.089696] 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70 [ 23.096774] [ 23.096774] other info that might help us debug this: [ 23.103494] Possible unsafe locking scenario: [ 23.103494] [ 23.109584] CPU0 [ 23.112093] ---- [ 23.114601] lock(_xmit_ETHER); [ 23.117917] lock(_xmit_ETHER); [ 23.121233] [ 23.121233] *** DEADLOCK *** [ 23.121233] [ 23.127325] May be due to missing lock nesting notation [ 23.127325] [ 23.134315] 2 locks held by ip/2861: [ 23.137987] #0: 000000003b766c72 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x338/0x4e0 [ 23.146231] #1: 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70 [ 23.153757] [ 23.153757] stack backtrace: [ 23.158243] CPU: 0 PID: 2861 Comm: ip Not tainted 5.0.0-rc3-00013-g56c857a1b8d3 #118 [ 23.166212] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT) [ 23.172843] Call trace: [ 23.175358] dump_backtrace+0x0/0x188 [ 23.179116] show_stack+0x14/0x20 [ 23.182524] dump_stack+0xb4/0xec [ 23.185928] __lock_acquire+0x123c/0x1860 [ 23.190048] lock_acquire+0xc8/0x248 [ 23.193724] _raw_spin_lock_bh+0x40/0x58 [ 23.197755] dev_set_rx_mode+0x1c/0x38 [ 23.201607] dev_set_promiscuity+0x3c/0x50 [ 23.205820] dsa_slave_change_rx_flags+0x5c/0x70 [ 23.210567] __dev_set_promiscuity+0x148/0x1e0 [ 23.215136] __dev_set_rx_mode+0x74/0x98 [ 23.219167] dev_uc_add+0x54/0x70 [ 23.222575] macvlan_open+0x170/0x1d0 [ 23.226336] __dev_open+0xe0/0x160 [ 23.229830] __dev_change_flags+0x16c/0x1b8 [ 23.234132] dev_change_flags+0x20/0x60 [ 23.238074] do_setlink+0x2d0/0xc50 [ 23.241658] __rtnl_newlink+0x5f8/0x6e8 [ 23.245601] rtnl_newlink+0x50/0x78 [ 23.249184] rtnetlink_rcv_msg+0x360/0x4e0 [ 23.253397] netlink_rcv_skb+0xe8/0x130 [ 23.257338] rtnetlink_rcv+0x14/0x20 [ 23.261012] netlink_unicast+0x190/0x210 [ 23.265043] netlink_sendmsg+0x288/0x350 [ 23.269075] sock_sendmsg+0x18/0x30 [ 23.272659] ___sys_sendmsg+0x29c/0x2c8 [ 23.276602] __sys_sendmsg+0x60/0xb8 [ 23.280276] __arm64_sys_sendmsg+0x1c/0x28 [ 23.284488] el0_svc_common+0xd8/0x138 [ 23.288340] el0_svc_handler+0x24/0x80 [ 23.292192] el0_svc+0x8/0xc This looks fairly harmless (no actual deadlock occurs), and is fixed in a similar way to c6894dec ("bridge: fix lockdep addr_list_lock false positive splat") by putting the addr_list_lock in its own lockdep class. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
-
Sebastian Andrzej Siewior authored
[ Upstream commit 53bc8d2a ] During sendmsg() a cloned skb is saved via dp83640_txtstamp() in ->tx_queue. After the NIC sends this packet, the PHY will reply with a timestamp for that TX packet. If the cable is pulled at the right time I don't see that packet. It might gets flushed as part of queue shutdown on NIC's side. Once the link is up again then after the next sendmsg() we enqueue another skb in dp83640_txtstamp() and have two on the list. Then the PHY will send a reply and decode_txts() attaches it to the first skb on the list. No crash occurs since refcounting works but we are one packet behind. linuxptp/ptp4l usually closes the socket and opens a new one (in such a timeout case) so those "stale" replies never get there. However it does not resume normal operation anymore. Purge old skbs in decode_txts(). Fixes: cb646e2b ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
Kurt Kanzenbach <kurt@linutronix.de> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit fc42a689 ] The test_insert_dup() function from lib/test_rhashtable.c passes a pointer to a stack object to rhltable_init(). Allocate the hash table dynamically to avoid that the following is reported with object debugging enabled: ODEBUG: object (ptrval) is on stack (ptrval), but NOT annotated. WARNING: CPU: 0 PID: 1 at lib/debugobjects.c:368 __debug_object_init+0x312/0x480 Modules linked in: EIP: __debug_object_init+0x312/0x480 Call Trace: ? debug_object_init+0x1a/0x20 ? __init_work+0x16/0x30 ? rhashtable_init+0x1e1/0x460 ? sched_clock_cpu+0x57/0xe0 ? rhltable_init+0xb/0x20 ? test_insert_dup+0x32/0x20f ? trace_hardirqs_on+0x38/0xf0 ? ida_dump+0x10/0x10 ? jhash+0x130/0x130 ? my_hashfn+0x30/0x30 ? test_rht_init+0x6aa/0xab4 ? ida_dump+0x10/0x10 ? test_rhltable+0xc5c/0xc5c ? do_one_initcall+0x67/0x28e ? trace_hardirqs_off+0x22/0xe0 ? restore_all_kernel+0xf/0x70 ? trace_hardirqs_on_thunk+0xc/0x10 ? restore_all_kernel+0xf/0x70 ? kernel_init_freeable+0x142/0x213 ? rest_init+0x230/0x230 ? kernel_init+0x10/0x110 ? schedule_tail_wrapper+0x9/0xc ? ret_from_fork+0x19/0x24 Cc: Thomas Graf <tgraf@suug.ch> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Govindarajulu Varadarajan authored
[ Upstream commit 7596175e ] In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does not set skb->ip_summed. So IPv6 rx checksum is not offloaded. Signed-off-by:
Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9b1f19d8 ] Similarly to commit 276bdb82 ("dccp: check ccid before dereferencing") it is wise to test for a NULL ccid. kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.0.0-rc3+ #37 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b kobject: 'loop5' (0000000080f78fc1): kobject_uevent_env RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 000000008db5e000 CR4: 00000000001406e0 kobject: 'loop5' (0000000080f78fc1): fill_kobj_path: path = '/devices/virtual/block/loop5' DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: dccp_rcv_state_process+0x2b6/0x1af6 net/dccp/input.c:654 dccp_v4_do_rcv+0x100/0x190 net/dccp/ipv4.c:688 sk_backlog_rcv include/net/sock.h:936 [inline] __sk_receive_skb+0x3a9/0xea0 net/core/sock.c:473 dccp_v4_rcv+0x10cb/0x1f80 net/dccp/ipv4.c:880 ip_protocol_deliver_rcu+0xb6/0xa20 net/ipv4/ip_input.c:208 ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_local_deliver+0x1f0/0x740 net/ipv4/ip_input.c:255 dst_input include/net/dst.h:450 [inline] ip_rcv_finish+0x1f4/0x2f0 net/ipv4/ip_input.c:414 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_rcv+0xed/0x620 net/ipv4/ip_input.c:524 __netif_receive_skb_one_core+0x160/0x210 net/core/dev.c:4973 __netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5083 process_backlog+0x206/0x750 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x76d/0x1930 net/core/dev.c:6412 __do_softirq+0x30b/0xb11 kernel/softirq.c:292 run_ksoftirqd kernel/softirq.c:654 [inline] run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646 smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164 kthread+0x357/0x430 kernel/kthread.c:246 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 Modules linked in: ---[ end trace 58a0ba03bea2c376 ]--- RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 0000000009871000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Signed-off-by:
-
Eduardo Valentin authored
commit 03334ba8 upstream. Avoid warnings like this: thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function] thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz) Fixes: 0dd88793 ("thermal: hwmon: move hwmon support to single file") Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Eduardo Valentin <edubezval@gmail.com> Signed-off-by:
-
Eric Sandeen authored
commit 7d048df4 upstream. xfs_btree_sblock_verify_crc is a bool so should not be returning a failaddr_t; worse, if xfs_log_check_lsn fails it returns __this_address which looks like a boolean true (i.e. success) to the caller. (interestingly xfs_btree_lblock_verify_crc doesn't have the issue) Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Darrick J. Wong authored
commit a579121f upstream. In commit e53c4b59, I *tried* to teach xfs to force writeback when we fzero/fpunch right up to EOF so that if EOF is in the middle of a page, the post-EOF part of the page gets zeroed before we return to userspace. Unfortunately, I missed the part where PAGE_MASK is ~(PAGE_SIZE - 1), which means that we totally fail to zero if we're fpunching and EOF is within the first page. Worse yet, the same PAGE_MASK thinko plagues the filemap_write_and_wait_range call, so we'd initiate writeback of the entire file, which (mostly) masked the thinko. Drop the tricky PAGE_MASK and replace it with correct usage of PAGE_SIZE and the proper rounding macros. Fixes: e53c4b59 ("xfs: ensure post-EOF zeroing happens after zeroing part of a file") Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
-
Ye Yin authored
commit de724305 upsream. When project is set, we should use inode limit minus the used count Signed-off-by:
Ye Yin <dbyin@tencent.com> Reviewed-by:
-
Dave Chinner authored
commit 9230a0b6 upstream. Long saga. There have been days spent following this through dead end after dead end in multi-GB event traces. This morning, after writing a trace-cmd wrapper that enabled me to be more selective about XFS trace points, I discovered that I could get just enough essential tracepoints enabled that there was a 50:50 chance the fsx config would fail at ~115k ops. If it didn't fail at op 115547, I stopped fsx at op 115548 anyway. That gave me two traces - one where the problem manifested, and one where it didn't. After refining the traces to have the necessary information, I found that in the failing case there was a real extent in the COW fork compared to an unwritten extent in the working case. Walking back through the two traces to the point where the CWO fork extents actually diverged, I found that the bad case had an extra unwritten extent in it. This is likely because the bug it led me to had triggered multiple times in those 115k ops, leaving stray COW extents around. What I saw was a COW delalloc conversion to an unwritten extent (as they should always be through xfs_iomap_write_allocate()) resulted in a /written extent/: xfs_writepage: dev 259:0 ino 0x83 pgoff 0x17000 size 0x79a00 offset 0 length 0 xfs_iext_remove: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/2 offset 32 block 152 count 20 flag 1 caller xfs_bmap_add_extent_delay_real xfs_bmap_pre_update: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/1 offset 1 block 4503599627239429 count 31 flag 0 caller xfs_bmap_add_extent_delay_real xfs_bmap_post_update: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/1 offset 1 block 121 count 51 flag 0 caller xfs_bmap_add_ex Basically, Cow fork before: 0 1 32 52 +H+DDDDDDDDDDDD+UUUUUUUUUUU+ PREV RIGHT COW delalloc conversion allocates: 1 32 +uuuuuuuuuuuu+ NEW And the result according to the xfs_bmap_post_update trace was: 0 1 32 52 +H+wwwwwwwwwwwwwwwwwwwwwwww+ PREV Which is clearly wrong - it should be a merged unwritten extent, not an unwritten extent. That lead me to look at the LEFT_FILLING|RIGHT_FILLING|RIGHT_CONTIG case in xfs_bmap_add_extent_delay_real(), and sure enough, there's the bug. It takes the old delalloc extent (PREV) and adds the length of the RIGHT extent to it, takes the start block from NEW, removes the RIGHT extent and then updates PREV with the new extent. What it fails to do is update PREV.br_state. For delalloc, this is always XFS_EXT_NORM, while in this case we are converting the delayed allocation to unwritten, so it needs to be updated to XFS_EXT_UNWRITTEN. This LF|RF|RC case does not do this, and so the resultant extent is always written. And that's the bug I've been chasing for a week - a bmap btree bug, not a reflink/dedupe/copy_file_range bug, but a BMBT bug introduced with the recent in core extent tree scalability enhancements. Signed-off-by:
-
Dave Chinner authored
commit d43aaf16 upstream. When retrying a failed inode or dquot buffer, xfs_buf_resubmit_failed_buffers() clears all the failed flags from the inde/dquot log items. In doing so, it also drops all the reference counts on the buffer that the failed log items hold. This means it can drop all the active references on the buffer and hence free the buffer before it queues it for write again. Putting the buffer on the delwri queue takes a reference to the buffer (so that it hangs around until it has been written and completed), but this goes bang if the buffer has already been freed. Hence we need to add the buffer to the delwri queue before we remove the failed flags from the log items attached to the buffer to ensure it always remains referenced during the resubmit process. Reported-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
-
Brian Foster authored
commit 59e42931 upstream. Page writeback indirectly handles shared extents via the existence of overlapping COW fork blocks. If COW fork blocks exist, writeback always performs the associated copy-on-write regardless if the underlying blocks are actually shared. If the blocks are shared, then overlapping COW fork blocks must always exist. fstests shared/010 reproduces a case where a buffered write occurs over a shared block without performing the requisite COW fork reservation. This ultimately causes writeback to the shared extent and data corruption that is detected across md5 checks of the filesystem across a mount cycle. The problem occurs when a buffered write lands over a shared extent that crosses an extent size hint boundary and that also happens to have a partial COW reservation that doesn't cover the start and end blocks of the data fork extent. For example, a buffered write occurs across the file offset (in FSB units) range of [29, 57]. A shared extent exists at blocks [29, 35] and COW reservation already exists at blocks [32, 34]. After accommodating a COW extent size hint of 32 blocks and the existing reservation at offset 32, xfs_reflink_reserve_cow() allocates 32 blocks of reservation at offset 0 and returns with COW reservation across the range of [0, 34]. The associated data fork extent is still [29, 35], however, which isn't fully covered by the COW reservation. This leads to a buffered write at file offset 35 over a shared extent without associated COW reservation. Writeback eventually kicks in, performs an overwrite of the underlying shared block and causes the associated data corruption. Update xfs_reflink_reserve_cow() to accommodate the fact that a delalloc allocation request may not fully cover the extent in the data fork. Trim the data fork extent appropriately, just as is done for shared extent boundaries and/or existing COW reservations that happen to overlap the start of the data fork extent. This prevents shared/010 failures due to data corruption on reflink enabled filesystems. Signed-off-by:
-
Dave Chinner authored
commit 837514f7 upstream. generic/070 on 64k block size filesystems is failing with a verifier corruption on writeback or an attribute leaf block: [ 94.973083] XFS (pmem0): Metadata corruption detected at xfs_attr3_leaf_verify+0x246/0x260, xfs_attr3_leaf block 0x811480 [ 94.975623] XFS (pmem0): Unmount and run xfs_repair [ 94.976720] XFS (pmem0): First 128 bytes of corrupted metadata buffer: [ 94.978270] 000000004b2e7b45: 00 00 00 00 00 00 00 00 3b ee 00 00 00 00 00 00 ........;....... [ 94.980268] 000000006b1db90b: 00 00 00 00 00 81 14 80 00 00 00 00 00 00 00 00 ................ [ 94.982251] 00000000433f2407: 22 7b 5c 82 2d 5c 47 4c bb 31 1c 37 fa a9 ce d6 "{\.-\GL.1.7.... [ 94.984157] 0000000010dc7dfb: 00 00 00 00 00 81 04 8a 00 0a 18 e8 dd 94 01 00 ................ [ 94.986215] 00000000d5a19229: 00 a0 dc f4 fe 98 01 68 f0 d8 07 e0 00 00 00 00 .......h........ [ 94.988171] 00000000521df36c: 0c 2d 32 e2 fe 20 01 00 0c 2d 58 65 fe 0c 01 00 .-2.. ...-Xe.... [ 94.990162] 000000008477ae06: 0c 2d 5b 66 fe 8c 01 00 0c 2d 71 35 fe 7c 01 00 .-[f.....-q5.|.. [ 94.992139] 00000000a4a6bca6: 0c 2d 72 37 fc d4 01 00 0c 2d d8 b8 f0 90 01 00 .-r7.....-...... [ 94.994789] XFS (pmem0): xfs_do_force_shutdown(0x8) called from line 1453 of file fs/xfs/xfs_buf.c. Return address = ffffffff815365f3 This is failing this check: end = ichdr.freemap[i].base + ichdr.freemap[i].size; if (end < ichdr.freemap[i].base) >>>>> return __this_address; if (end > mp->m_attr_geo->blksize) return __this_address; And from the buffer output above, the freemap array is: freemap[0].base = 0x00a0 freemap[0].size = 0xdcf4 end = 0xdd94 freemap[1].base = 0xfe98 freemap[1].size = 0x0168 end = 0x10000 freemap[2].base = 0xf0d8 freemap[2].size = 0x07e0 end = 0xf8b8 These all look valid - the block size is 0x10000 and so from the last check in the above verifier fragment we know that the end of freemap[1] is valid. The problem is that end is declared as: uint16_t end; And (uint16_t)0x10000 = 0. So we have a verifier bug here, not a corruption. Fix the verifier to use uint32_t types for the check and hence avoid the overflow. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=201577Signed-off-by:
-
Christophe JAILLET authored
commit 132bf672 upstream. In this function, once 'buf' has been allocated, we unconditionally return 0. However, 'error' is set to some error codes in several error handling paths. Before commit 232b5194 ("xfs: simplify the xfs_getbmap interface") this was not an issue because all error paths were returning directly, but now that some cleanup at the end may be needed, we must propagate the error code. Fixes: 232b5194 ("xfs: simplify the xfs_getbmap interface") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
-
