removed mt352_aver777_tuner_calc_regs, using dvb_pll_attach, instead.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.

The functionality is added to dvb-pll, where all the other code that 
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.

In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link.  Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.

It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).

It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This driver were made based on tea5761 specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This is a reimplementation of the zs driver for the serial subsystem.  Any
resemblance to the old driver is purely coincidential.  ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...

Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e.  ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3.  It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.

This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We can't show the extra logo from boot code if FB is built as a module.
Make the FB_LOGO_EXTRA depend on FB=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If, in dm_create_persistent(), the call to create_singlethread_workqueue()
fails then we'll return without freeing the memory allocated to 'ps', thus
leaking sizeof(struct pstore) bytes.  This patch fixes the leak.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With the slab zeroing allocations cleanups Christoph stubbed in a generic
kzalloc(), which was missed on SLOB. Follow the SLAB/SLUB changes and
kill off the __kzalloc() wrapper that SLOB was using.
Reported-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The old IDE driver is not ready to take generic SCSI commands, even if
it uses them for some specific issues (ie the tray open/close ioctls for
IDE CD-ROM's). Pointed out by Bartlomiej.

I'm sure we'll have it fixed properly soon enough, but for now we should
not allow it to cause problems.

Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I really don't see anybody else wanting to select it ;)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Fix broken logic, SIGA flags must be bitwise ORed
  [S390] cio: Dont print trailing \0 in modalias_show().
  [S390] Simplify stack trace.
  [S390] z/VM unit record device driver
  [S390] vmcp cleanup
  [S390] qdio: output queue stall on FCP and network devices
  [S390] Fix disassembly of RX_URRD, SI_URD & PC-relative instructions.
  [S390] Update default configuration.

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (21 commits)
  [WATCHDOG] at32ap700x_wdt.c - Fix compilation warnings
  [WATCHDOG] at32ap700x_wdt.c - Add spinlock support
  [WATCHDOG] at32ap700x_wdt.c - Add nowayout + MAGICCLOSE features
  [WATCHDOG] at32ap700x_wdt.c - timeout module parameter patch
  [WATCHDOG] at32ap700x_wdt.c - checkpatch.pl-0.05 clean-up's
  [WATCHDOG] change s3c2410_wdt to using dev_() macros for output
  [WATCHDOG] s3c2410_wdt announce initialisation
  [WATCHDOG] at32ap700x-wdt: add iounmap if probe function fails
  [WATCHDOG] at32ap700x-wdt: add missing iounmap in _remove
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix-2
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix
  [WATCHDOG] Watchdog driver for AT32AP700X devices
  [WATCHDOG] Mixcom Watchdog - CodingStyle clean-up
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - checkcard part 2
  [WATCHDOG] Mixcom Watchdog - checkcard
  [WATCHDOG] Mixcom Watchdog - get rid of port offset's
  [WATCHDOG] Mixcom Watchdog - update "Documentation"
  [WATCHDOG] Remove the redundant check for pwrite() in EP93XXX watchdog.
  ...

* 'bsg' of git://git.kernel.dk/data/git/linux-2.6-block:
  bsg: fix missing space in version print
  Don't define empty struct bsg_class_device if !CONFIG_BLK_DEV_BSG
  bsg: Kconfig updates
  bsg: minor cleanup
  bsg: device hash table cleanup
  bsg: fix initialization error handling bugs
  bsg: mark FUJITA Tomonori as bsg maintainer
  bsg: convert to dynamic major
  bsg: address various review comments

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix debug compilation error

* 'isdn-cleanup' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] HiSax hfc_pci: minor cleanups
  [ISDN] HiSax bkm_a4t: split setup into two smaller functions
  [ISDN] HiSax enternow: split setup into 3 smaller functions
  [ISDN] HiSax netjet_u: split setup into 3 smaller functions
  [ISDN] HiSax netjet_s: code movement, prep for hotplug
  [ISDN] HiSax: move card state alloc/setup code into separate functions
  [ISDN] HiSax: move card setup into separate function

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Kill bogus set_fs(KERNEL_DS) in do_rt_sigreturn().
  [SPARC64]: Update defconfig.
  [SPARC64]: Kill explicit %gl register reference.

* 'uninit-var' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  arch/i386/* fs/* ipc/*: mark variables with uninitialized_var()
  drivers/*: mark variables with uninitialized_var()

* 'warnings' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  drivers/atm/ambassador: kill uninit'd var warning, and fix bug
  [libata] sata_mv: use pci_try_set_mwi()
  drivers/infiniband/hw/mthca/mthca_qp: kill uninit'd var warning
  drivers/net/wan/sbni: kill uninit'd var warning
  drivers/mtd/ubi/eba: minor cleanup: tighten scope of a local var
  drivers/telephony/ixj: cleanup and fix gcc warning
  drivers/net/wan/pc300_drv: fix bug caught by gcc warning
  drivers/usb/misc/auerswald: fix status check, remove redundant check
  [netdrvr] eepro100, ne2k-pci: abort resume if pci_enable_device() fails
  [netdrvr] natsemi: Fix device removal bug
  kernel/auditfilter: kill bogus uninit'd-var compiler warning

... or we end up with header include order problems from hell.

E.g. on m68k this is 100% fatal - local_irq_enable() there
wants preempt_count(), which wants task_struct fields, which
we won't have when we are in smp.h pulled from sched.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

* trim trailing whitespace
* remove CONFIG_PCI ifdefs, this driver is always PCI (Kconfig enforced)
* remove return statements at the tail of a function
* remove indentation levels by returning an error code immediately.
  Makes the code much more readable, and easier to update to PCI hotplug
  API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.

Well, CONFIG_PCI useless ifdef was removed.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) Remove CONFIG_PCI ifdefs.  PCI is required in Kconfig.

2) Break up setup_netjet_s() into three separate internal functions.
This helps facilitate upcoming use of PCI hotplug API, and in addition
makes the code much easier to follow.

No code is changed, just moved around.  I even kept the out-of-favor
"return(0)" style used in the current source code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Just code movement.  No code changes or cleanups besides that which
is required to call the new functions from the old code site.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fixes the following build error:
  CC      sound/pci/mixart/mixart_hwdep.o
sound/pci/mixart/mixart_hwdep.c: In function ‘mixart_hwdep_dsp_load’:
sound/pci/mixart/mixart_hwdep.c:610: error: implicit declaration of function ‘vmalloc’
sound/pci/mixart/mixart_hwdep.c:617: error: implicit declaration of function ‘vfree’
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the following build-error:

 CC      drivers/parisc/hppb.o
drivers/parisc/hppb.c: In function ‘hppb_probe’:
drivers/parisc/hppb.c:73: error: implicit declaration of function ‘ccio_request_resource’
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Mark variables with uninitialized_var() if such a warning appears,
and analysis proves that the var is initialized properly on all paths
it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

An uninitialized variable warning illuminated an area where indeed the
variable was being used without initialization.  Unfortunately, after
verifying all such paths were fixed, the warning still appears.  So we
follow the initialization practice of other variables in this function.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Because sometimes in life, it's ok to fail.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/infiniband/hw/mthca/mthca_qp.c: In function
  ‘mthca_tavor_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1594: warning: ‘f0’ may be used
  uninitialized in this function
drivers/infiniband/hw/mthca/mthca_qp.c: In function
  ‘mthca_arbel_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1949: warning: ‘f0’ may be used
  uninitialized in this function

Initializing 'f0' is not strictly necessary in either case, AFAICS.

I was considering use of uninitialized_var(), but looking at the
complex flow of control in each function, I feel it is wiser and
safer to simply zero the var and be certain of ourselves.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

It's actually convenient in the code to initialize this and a sister
variable to zero.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) Fix gcc uninit'd var warnings by adding 'default' switch stmt labels
in two cases.  It was lightning-strikes unlikely that a problem would
ever arise, but not impossible.

2) Tighten the scope of 'blankword' in two cases.
Signed-off-by: Jeff Garzik <jeff@garzik.org>