- 27 Sep, 2011 2 commits
-
-
- 23 Sep, 2011 10 commits
-
-
Arik Nemtsov authored
Use the AP_MAX_LINKS as the upper boundary for traversing the links array, thereby guaranteeing BA sessions with all connected STAs are stopped when the stop_ba event is received. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Fix an erroneous labeling of array boundaries in the fw_status structure. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Eliad Peller authored
Save the configured bitrate, and use the min allowed rate as the basic rate (e.g. when scanning). Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Arik Nemtsov authored
If a hidden SSID is requested, generate a probe response template containing the real SSID. Depends on the patch "mac80211: add ssid config to bss information in AP-mode". Signed-off-by:
-
Eliad Peller authored
On roaming, the auth and assoc req are sent with the sta hlid. This is wrong, as the sta hlid is configured according to the old ap. Use the dev_hlid instead. Move the wl1271_tx_update_filters() call into wl1271_tx_get_hlid(), so wl->dev_hlid will be valid. Signed-off-by:
-
Eliad Peller authored
There is a race condition between wl1271_tx_work() and the channel switch, so make sure all the pending packets are being sent before switching channel. Signed-off-by:
-
Eliad Peller authored
wl12xx uses a single probe response template, regardless of the probe request. However, the P2P spec forbids including the p2p ie in some cases (e.g. the probe request didn't include the p2p ie). The fw responds only to probe requests that don't include the p2p ie, and passes up probe requests that include them (the supplicant will answer them). Thus, strip the p2p ie from the probe response template. Signed-off-by:
-
Eliad Peller authored
wl12xx uses the beacon as the probe response template. However, the beacon includes a TIM ie, which shouldn't exist in the probe response. Delete it from the skb before configuring the probe response template. Signed-off-by:
-
Shahar Levi authored
We were including only 11b rates in IBSS mode. This patch adds OFDM rates. [Rephrased commit log and removed one unnecessary comment. -- Luca] Signed-off-by:
Shahar Levi <shahar_levi@ti.com> Signed-off-by:
-
Shahar Levi authored
Due to some changes in PM in recent kernels, the sdio_test module has been broken for a while. This patch fixes the code that powers the card on and off. Also made some small indentation fixes in the Makefile. [Rephrased commit log and removed the change in the FW name, since it's done in another patch. -- Luca] Signed-off-by:
-
- 22 Sep, 2011 1 commit
-
-
Luciano Coelho authored
We were using incorrect max and min dwell times during forced passive scans because we were still using the active scan states to scan (passively) the channels that were not marked as passive. Instead of doing passive scans in active states, we now skip active states and scan for all channels in passive states. Cc: <stable@kernel.org> # 2.6.36+ Signed-off-by:
-
- 21 Sep, 2011 27 commits
-
-
Randy Dunlap authored
nwcwilink.c uses nci_*() interfaces, so it should depend on NFC_NCI. Fixes these build errors: ERROR: "nci_register_device" [drivers/nfc/nfcwilink.ko] undefined! ERROR: "nci_allocate_device" [drivers/nfc/nfcwilink.ko] undefined! ERROR: "nci_recv_frame" [drivers/nfc/nfcwilink.ko] undefined! ERROR: "nci_free_device" [drivers/nfc/nfcwilink.ko] undefined! ERROR: "nci_unregister_device" [drivers/nfc/nfcwilink.ko] undefined! Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Dan Carpenter authored
We dereference "rate" on the lines before so the checks here are too late to help. This function is only called from mwifiex_dump_station_info() and "rate" is always a non-NULL pointer so the check can be removed. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Dan Carpenter authored
We're not likely to hit this small memory leak, but lets fix it anyway to keep the static checkers happy. Signed-off-by:
-
Amit Beka authored
iwl_trans_rx_alloc is only called from iwl_rx_init, so no need to init the lists twice. Signed-off-by:
Amit Beka <amit.beka@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
During my works on the transport layer I removed code that updated a local variable (is_agg) that is needed to keep the pending_frames count up to date. Fix this. Also, there should be no way to have a packet with TX_CTL_AMPDU set while the internal aggregation state machine is not in AGG_ON state. Add a WARN_ON to ensure that. Signed-off-by:
-
Emmanuel Grumbach authored
This has been removed but the declaration hasn't. Signed-off-by:
-
Emmanuel Grumbach authored
This simplifies both the transport layer and the upper layer. Kill the union in the device command, which avoids the funny syntax we had: cmd->cmd.payload. Signed-off-by:
-
Emmanuel Grumbach authored
Before this patch, the upper layer could register a callback for each host command. This mechanism allowed the upper layer to have different callbacks for the same command ID. In fact, it wasn't used and the rx_handlers is enough: same callback for all the command with a specific command ID. The iwl_send_add_station needs the access the command that was sent while handling the response (regardless if the command was sent in SYNC or ASYNC mode). So now, all the handlers receive the host command that was sent. This implies a change in the handler signature. Signed-off-by:
-
Johannes Berg authored
If we're associated and want to do P2P at the same time, the scan for remain-on-channel is currently limited to 80ms because of the way the device will behave in that case. Instead of doing that, split up the dwell times into little pieces. It will not actually be a single big dwell time then, but will be close enough. This improves robustness of P2P in such scenarios. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
Since the driver split there's no more need for shared/non-shared private station data so remove struct iwl_station_priv_common entirely. Signed-off-by:
-
Johannes Berg authored
Since the driver split there's no longer a need to have the scan code scattered across multiple files, so move it all back to iwl-scan.c Signed-off-by:
Wey-Yi Guy <wey-yi.guy@intel.com> Signed-off-by:
-
Thomas Pedersen authored
Send a Mesh Peering Close frame when we deactivate a mesh peer link. Signed-off-by:
Thomas Pedersen <thomas@cozybit.com> Signed-off-by:
-
Johannes Berg authored
When an AP interface is removed without the AP/VLAN interfaces having been removed before already, the AP-VLAN interface might still have sleeping stations and buffer multicast frames which will happen on the AP interface. Thus, we need to remove AP/VLAN interfaces before purging buffered broadcast frames. Signed-off-by:
-
Luiz Augusto von Dentz authored
l2cap_create_iframe_pdu is only used in l2cap_core.c Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi>
-
Andre Guedes authored
The mgmt_device_found event will be used to report LE devices found during discovery procedure. Since LE advertising reports events doesn't have class of device information, we need to check if 'dev_class' is not NULL before copying it. Signed-off-by:
Andre Guedes <andre.guedes@openbossa.org> Signed-off-by:
-
Andre Guedes authored
This patch reduces the critial region (protected by hdev->lock) in hci_cc_le_set_scan_enable(). This way, only really required code is synchronized. Signed-off-by:
-
Anderson Briglia authored
This patch fixes wrong memcpy size when copying rand value to HCI_OP_LE_START_ENC command. The compiler pretends that the array parameter was declared as a pointer and sizeof reports the size of the pointer. [1] [1] http://www.c-faq.com/aryptr/aryparmsize.htmlSigned-off-by:
Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by:
Anderson Lizardo <anderson.lizardo@openbossa.org> Signed-off-by:
-
Vinicius Costa Gomes authored
For now, only the LTK is properly supported. We are able to receive and generate the other types of keys, but we are not able to use them. So it's better not request them to be distributed. Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by:
-
Vinicius Costa Gomes authored
For slave initiated security, we should set a default security level, for now BT_SECURITY_MEDIUM. Signed-off-by:
-
Vinicius Costa Gomes authored
This reverts commit 5a0a8b49. If we use separate messages and list for SMP specific keys we can simplify the code. Conflicts: net/bluetooth/mgmt.c Signed-off-by:
-
Vinicius Costa Gomes authored
When receiving a security request from the remote device we should find if there is already a LTK associated with the remote device, if found we should use it to encrypt the link. Signed-off-by:
-
Vinicius Costa Gomes authored
Until we support any pairing method (Passkey Entry, OOB) that gives MITM protection we shouldn't send that we have MITM protection. Signed-off-by:
-
Antti Julku authored
Add management interface events for blocking/unblocking a device. Sender of the block device command gets cmd complete and other mgmt sockets get the event. Event is also sent to mgmt sockets when blocking is done with ioctl, e.g when blocking a device with hciconfig. This makes it possible for bluetoothd to track status of blocked devices when a third party block or unblocks a device. Event sending is handled in mgmt_device_blocked function which gets called from hci_blacklist_add in hci_core.c. A pending command is added in mgmt_block_device, so that it can found when sending the event - the event is not sent to the socket from which the pending command came. Locks were moved out from hci_core.c to hci_sock.c and mgmt.c, because locking is needed also for mgmt_pending_add in mgmt.c. Signed-off-by:
Antti Julku <antti.julku@nokia.com> Signed-off-by:
-
Vinicius Costa Gomes authored
This lifts the requirement of 16 digits pin codes when pairing with devices that do not support SSP when using the mgmt interface. Signed-off-by:
-
Vinicius Costa Gomes authored
The HIGH security level requires a 16 digit pin code for non-SSP bondings. Sometimes this requirement is not acceptable and we still want protection againts MITM attacks (which is something that the MEDIUM security level doesn't provide), for that we should allow another way to request authentication without using the HIGH security level. Signed-off-by:
-
Vinicius Costa Gomes authored
The function crypto_blkcipher_setkey() called by smp_e() can sleep, so all the crypto work has to be moved to hci_dev workqueue. Signed-off-by:
-
Vinicius Costa Gomes authored
The objective is to make the core to have as little as possible information about SMP procedures and logic. Now, all the SMP specific information is hidden from the core. Signed-off-by:
-
