Suspending an open usbnet device results in constant
rescheduling of usbnet_bh.

commit 65841fd5 "usbnet: handle remote wakeup asap"
refactored the usbnet_bh code to allow sharing the
urb allocate and submit code with usbnet_resume. In
this process, a test for, and immediate return on,
ENOLINK from rx_submit was unintentionally dropped.

The rx queue will not grow if rx_submit fails,
making usbnet_bh reschedule itself.  This results
in a softirq storm if the error is persistent.
rx_submit translates the usb_submit_urb error
EHOSTUNREACH into ENOLINK, so this is an expected
and persistent error for a suspended device. The
old code tested for this condition and avoided
rescheduling.  Putting this test back.

Cc: <stable@vger.kernel.org> # v3.5
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via
skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of
sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up
by __sctp_write_space().

Buffer space charged via sctp_set_owner_w() is released in sctp_wfree()
which calls __sctp_write_space() directly.

Buffer space charged via skb_set_owner_w() is released via sock_wfree()
which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set.
sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets.

Therefore if sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is
interrupted by a signal.

This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ...

Charging for the data twice does not make sense in the first place, it
leads to overcharging sndbuf by a factor 2. Therefore this patch only
charges a single byte in wmem_alloc when transmitting an SCTP packet to
ensure that the socket stays alive until the packet has been released.

This means that control chunks are no longer accounted for in wmem_alloc
which I believe is not a problem as skb->truesize will typically lead
to overcharging anyway and thus compensates for any control overhead.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_edemux() can handle either a regular socket or a timewait socket
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull CIFS fixes from Steve French.

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix cifs_do_create error hadnling
  cifs: print error code if smb signature verification fails
  CIFS: Fix log messages in packet checking for SMB2
  CIFS: Protect i_nlink from being negative

Pull networking fixes from David Miller:

 1) NLA_PUT* --> nla_put_* conversion got one case wrong in
    nfnetlink_log, fix from Patrick McHardy.

 2) Missed error return check in ipw2100 driver, from Julia Lawall.

 3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
    from Eric Dumazet.

 4) SFC driver erroneously reversed src and dst when reporting filters
    via ethtool.

 5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
    sja1000 can platform driver, from Alexey Khoroshilov and Sven
    Schmitt.

 6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
    take the lock when we really need to.  From Eric Dumazet.

 7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.

 8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
    fix from Yuchung Cheng.

 9) Revert netpoll change, and fix what was actually a driver specific
    problem.  From Amerigo Wang.  This should cure bootup hangs with
    netconsole some people reported.

10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
    pointer.  From Ian Campbell.

11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.

12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.

13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
    situation.  From Oliver Neukum.

14) The davinci ethernet driver triggers an OOPS on removal because it
    frees an MDIO object before unregistering it.  Fix from Bin Liu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  net: qmi_wwan: add several new Gobi devices
  fddi: 64 bit bug in smt_add_para()
  net: ethernet: fix kernel OOPS when remove davinci_mdio module
  net/xfrm/xfrm_state.c: fix error return code
  net: ipv6: fix error return code
  net: qmi_wwan: new device: Foxconn/Novatel E396
  usbnet: fix deadlock in resume
  cs89x0 : packet reception not working
  netfilter: nf_conntrack: fix racy timer handling with reliable events
  bnx2x: Correct the ndo_poll_controller call
  bnx2x: Move netif_napi_add to the open call
  ipv4: must use rcu protection while calling fib_lookup
  bnx2x: fix 57840_MF pci id
  net: ipv4: ipmr_expire_timer causes crash when removing net namespace
  e1000e: DoS while TSO enabled caused by link partner with small MSS
  l2tp: avoid to use synchronize_rcu in tunnel free function
  gianfar: fix default tx vlan offload feature flag
  netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
  xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
  netfilter: nfnetlink_log: fix error return code in init path
  ...

Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions.  Re-syncing the
list of supported devices with qcserial.

Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@tempietto.lan>

The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line.  The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@tempietto.lan>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

davinci mdio device is not unregistered from mdiobus when removing
the module, which causes BUG_ON() when free the device from mdiobus.

Calling mdiobus_unregister() before mdiobus_free() fixes the issue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize return variable before exiting on an error path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize return variable before exiting on an error path.

The initial initialization of the return variable is also dropped, because
that value is never used.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Foxconn-branded Novatel E396, Gobi3k modem.

Cc: Dan Williams <dcbw@redhat.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Ben Chan <benchan@google.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

A usbnet device can share a multifunction device
with a storage device. If the storage device is autoresumed
the usbnet devices also needs to be autoresumed. Allocating
memory with GFP_KERNEL can deadlock in this case.

This should go back into all kernels that have
commit 65841fd5
That is 3.5
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The RxCFG register of the CS89x0 could be configured incorrectly
(because of misplaced parentheses), resulting in the disabling
of packet reception.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.

This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following lockdep splat was reported by Pavel Roskin :

[ 1570.586223] ===============================
[ 1570.586225] [ INFO: suspicious RCU usage. ]
[ 1570.586228] 3.6.0-rc3-wl-main #98 Not tainted
[ 1570.586229] -------------------------------
[ 1570.586231] /home/proski/src/linux/net/ipv4/route.c:645 suspicious rcu_dereference_check() usage!
[ 1570.586233]
[ 1570.586233] other info that might help us debug this:
[ 1570.586233]
[ 1570.586236]
[ 1570.586236] rcu_scheduler_active = 1, debug_locks = 0
[ 1570.586238] 2 locks held by Chrome_IOThread/4467:
[ 1570.586240]  #0:  (slock-AF_INET){+.-...}, at: [<ffffffff814f2c0c>] release_sock+0x2c/0xa0
[ 1570.586253]  #1:  (fnhe_lock){+.-...}, at: [<ffffffff815302fc>] update_or_create_fnhe+0x2c/0x270
[ 1570.586260]
[ 1570.586260] stack backtrace:
[ 1570.586263] Pid: 4467, comm: Chrome_IOThread Not tainted 3.6.0-rc3-wl-main #98
[ 1570.586265] Call Trace:
[ 1570.586271]  [<ffffffff810976ed>] lockdep_rcu_suspicious+0xfd/0x130
[ 1570.586275]  [<ffffffff8153042c>] update_or_create_fnhe+0x15c/0x270
[ 1570.586278]  [<ffffffff815305b3>] __ip_rt_update_pmtu+0x73/0xb0
[ 1570.586282]  [<ffffffff81530619>] ip_rt_update_pmtu+0x29/0x90
[ 1570.586285]  [<ffffffff815411dc>] inet_csk_update_pmtu+0x2c/0x80
[ 1570.586290]  [<ffffffff81558d1e>] tcp_v4_mtu_reduced+0x2e/0xc0
[ 1570.586293]  [<ffffffff81553bc4>] tcp_release_cb+0xa4/0xb0
[ 1570.586296]  [<ffffffff814f2c35>] release_sock+0x55/0xa0
[ 1570.586300]  [<ffffffff815442ef>] tcp_sendmsg+0x4af/0xf50
[ 1570.586305]  [<ffffffff8156fc60>] inet_sendmsg+0x120/0x230
[ 1570.586308]  [<ffffffff8156fb40>] ? inet_sk_rebuild_header+0x40/0x40
[ 1570.586312]  [<ffffffff814f4bdd>] ? sock_update_classid+0xbd/0x3b0
[ 1570.586315]  [<ffffffff814f4c50>] ? sock_update_classid+0x130/0x3b0
[ 1570.586320]  [<ffffffff814ec435>] do_sock_write+0xc5/0xe0
[ 1570.586323]  [<ffffffff814ec4a3>] sock_aio_write+0x53/0x80
[ 1570.586328]  [<ffffffff8114bc83>] do_sync_write+0xa3/0xe0
[ 1570.586332]  [<ffffffff8114c5a5>] vfs_write+0x165/0x180
[ 1570.586335]  [<ffffffff8114c805>] sys_write+0x45/0x90
[ 1570.586340]  [<ffffffff815d2722>] system_call_fastpath+0x16/0x1b
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c3def943 have added support for
new pci ids of the 57840 board, while failing to change the obsolete value
in 'pci_ids.h'.
This patch does so, allowing the probe of such devices.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.

Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g.  64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring.  This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e.  When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state.  After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.

Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.

Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.

This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit -
"b852b720 gianfar: fix bug caused by
87c288c6"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.

Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We're hitting bug while trying to reinsert an already existing
expectation:

kernel BUG at kernel/timer.c:895!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
 <IRQ>
 [<ffffffffa0069563>] nf_ct_expect_related_report+0x4a0/0x57a [nf_conntrack]
 [<ffffffff812d423a>] ? in4_pton+0x72/0x131
 [<ffffffffa00ca69e>] ip_nat_sdp_media+0xeb/0x185 [nf_nat_sip]
 [<ffffffffa00b5b9b>] set_expected_rtp_rtcp+0x32d/0x39b [nf_conntrack_sip]
 [<ffffffffa00b5f15>] process_sdp+0x30c/0x3ec [nf_conntrack_sip]
 [<ffffffff8103f1eb>] ? irq_exit+0x9a/0x9c
 [<ffffffffa00ca738>] ? ip_nat_sdp_media+0x185/0x185 [nf_nat_sip]

We have to remove the RTP expectation if the RTCP expectation hits EBUSY
since we keep trying with other ports until we succeed.
Reported-by: Rafal Fitt <rafalf@aplusc.com.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.

This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Initialize return variable before exiting on an error path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Initialize return variable before exiting on an error path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Initialize return variable before exiting on an error path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Against -net.

In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:

[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073]  [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075]  [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077]  [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080]  [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085]  [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088]  [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090]  [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095]  [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097]  [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100]  [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102]  [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240

by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:

http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpg
http://marc.info/?l=linux-netdev&m=134563282530588&w=2

So it is safe to fix be2net driver code directly.

This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>