The test if antenna diversity is at all enabled uses a local variable
'flags' to prepare the test condition, but uses 'ant->flags' when the test
is evaluated. The effect is that the diversity evaluation will never start.
I can see two solutions, use the 'flag' in the test condition or revert the
local flag change. My attached patch took alternative two.

Then the evaluation start but it will still not switch antenna. The problem
is a code section in rt2x00lib_config_antenna (). The effect of that code
section is that any change the diversity function perform will be
effectively shorten and no antenna selection command issued. The attached
patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all
other
Signed-off-by: Lars Ericsson <lars_ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To reduce scan time, enable fastcc for AR7010

(fastcc == fast channel change -- JWL)
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not maintain a persistent sdio_claim_host state. Instead,
claim host before doing IO and release host soon after.

This fixes several mmc deadlock scenarios, e.g. during
suspend/resume.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move the duplicated code into single static function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Clear the "start calib" flag only for new association,
The flag will be set in post_associate function to trigger
the runtime calibration. Set this flag to "0" will stop the
runtime sensitivity calibration
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The iwl_adjust_beacon_interval function is a bit
of black magic, so add comments to it describing
what it does. Also, in the case when there's no
beacon interval set, program the default into
the device (instead of adjusting, which results
in the max) since using the max in that case
interacts badly with dual-mode/PAN parameters.

Also update the PAN parameters accordingly and
use the same constant as here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

In dual-mode, a number of scenarios need to be
considered, and the firmware can be very picky
about them. Adjust the timing (most importantly
the beacon interval) according to the different
modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

When the PAN context is unused, there's no
need to continually update it in the device.
So track which contexts are active (with the
special case that the WLAN context is always
active ...) and only send their commands to
the device when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Even driver use rts/cts protection mode for aggregation packets by default.
Allow the protection mode to be configure through debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

When the beacon interval needs to be changed,
all we need to do is send updated timing to
the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

When only the PAN side was active, we gave no
time to the WLAN context, which is OK unless
we are scanning, which always happens on the
WLAN context. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

When sysassert happen, uCode will report the error code,
driver dump the information to dmesg. Here also remember
the last error code for future reference.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The default LQ is filled decreasingly using
iwl_get_prev_ieee_rate from a starting rate.
Since the starting rate is already the lowest one for
a specific band it should be actually filled evenly with
the starting rate: 1M and 6M for 5.2GHZ and 2.4GH respectively.
The bug is that for for A or G-only it decreases to
CCK rates which are not supported.
iwl_get_prev_ieee_rate function is just not band aware.
This affects broadcast station which lq table
is not updated by rs algorithm

G-only scenario is not treated by this patch

iwl_get_prev_ieee_rate is removed completely as it
is not used in other contexts
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The function has an unsigned return type, but returns a negative constant
to indicate an error condition.  Another error condition in the same
function is indicated by returning 0, and indeed the only call to the
function checks for 0 to detect errors, so the return of a negative value
it converted to a return of 0.

A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@exists@
identifier f;
constant C;
@@

 unsigned f(...)
 { <+...
*  return -C;
 ...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds an error message for the eeprom request failure
case. This way it's easier for the user to figure out
what went wrong.
Signed-off-by: Michael Büsch <mb@bu3sch.de>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For AR9271 chips, if partial reset is done while scanning, the cycpwrThr1
will be set to maximum. This causes the degrade in DL throughput.
So restore the ANI registers to default during the partial reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

By enabling fastcc, the scan time reduced to half.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This algorithm chooses the best main and alt lna out of
LNA1, LNA2, LNA1+LNA2 and LNA1-LNA2 to improve rx for single
chain chips(AR9285). This would greatly improve rx when there
is only one antenna is connected with AR9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is enabled only for ar9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make read/only data structures const. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make the startup and other data parameters that are read/only
const. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In uCode, BT state machine need to receive open envlope
command before perform calibration; followed by close envlope
command to move to next stage.

Since Linux has two separated uCode, one for init and the second
one for runtime; we use open envlope commands for init uCode to
indicate we are ready to perform calibration operation.
But for runtime uCode, we are not doing any init calibration,
so we issue open/close envlope commands to force uCode move to
"BT COEX ON" state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Otherwise the hardware scan handler could access an invalid scan request
structure.  The driver should cancel any pending hardware scans during
the suspend process anyway, so also add a warning if the hardware scan
is still pending when the device resumes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This function exists to clean-up after a hardware error or something
similar.  The restart is accomplished using the same infrastructure used
to resume after a suspend.  The suspend path cancels running scans, so
it seems appropriate to do that here as well for software-based scans.
If a hardware-based scan is pending, issue a warning message since this
indicates that the drivers has failed to clean-up after itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00usb_watchdog_reset_tx performs the same task
as rt2x00usb_kill_tx_queue, with the only difference
is that it waits for all entries to be returned to
the driver and for all frames the status has been
reported to mac80211.

We can easily split this task by calling rt2x00usb_kill_tx_queue,
sleep for a short period and invoke the TX status reporting
function. By adding the sleep() to the kill_entry we make sure
that even during shutdown we guarentee the entry has been killed when
the function returns. To make this work correctly the interrupt
handlers have to be updated to prevent checking for the RADIO_ENABLED
flag too early which prevents the ownership of the entry to be reset.
Additionally a check for the DEVICE_PRESENT flag is not required but
is nice to prevent race conditions when the device was unplugged.

Additionally rather then calling rt2x00usb_work_txdone() for
status reporting we let the driver perform the TX status reporting
first. If this is not sufficient then rt2x00usb_work_txdone() will
still be used to cleanup the mess.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The watchdog for rt2800usb triggers frequently causing all URB's
to be canceled often enough to interrupt the normal TX flow.
More research indicated that not the URB upload to the USB host
were hanging, but instead the TX status reports.

To correctly detect what is going on, we introduce Q_INDEX_DMA_DONE
which is an index counter between Q_INDEX_DONE and Q_INDEX and indicates
if the frame has been transfered to the device.

This also requires the rt2x00queue timeout functions to be updated
to differentiate between a DMA timeout (time between Q_INDEX and
Q_INDEX_DMA_DONE timeout) and a STATUS timeout (time between
Q_INDEX_DMA_DONE and Q_INDEX_DONE timeout)

All Q_INDEX_DMA_DONE code was taken from the RFC from
Helmut Schaa <helmut.schaa@googlemail.com> for the implementation
for watchdog for rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

USB devices upload their beacon and then automatically send
it out every beacon interval. However when killing a TX queue
we only kill the URB and not the actual transmission of the beacon.

This will reset the Beacon register to prevent any beacons from
being transmitted.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add PWR_PIN_CFG initialization for rt2800usb at the same point
as rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When configuring the MAC_ADDR or MAC_BSSID with an empty address,
the UNICAST_TO_ME_MASK and BSS_ID_MASK must also be reset to prevent
invalid interpretation of the addresses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to the legacy drivers the AUTOWAKEUP_CFG
register must be reset to 0 before loading the firmware.

Instead of during rt2800{pci,usb}_write_firmware it
must actually be done in rt2800_load_firmware() before
resetting the WPDMA_GLO_CFG and PWR_PIN_CFG registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of printing a warning when the PID, ACK, or WCID of
an entry don't match the TX status report, we should skip the
entry to search for the entry which actually does match
the TX status data.

This reduces the number of watchdog errors on the TX queues
for rt2800usb, and seems to improve the reliability of the
TX flow a bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>