These boards use the same offsets for the interrupt control registers.
For aesthetics, remove the current defines and use common ones.

Fix the switch() in pci_dio_reset() to use common code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, use a common comment for the switch() that disables and clears
interrupts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, move the disable of the channel freeze for the PCI-1752
and PCI-1756 boards out of the switch used to disable and clear interrupts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, use a default case in the switch (board->cardtype) used
to reset the various boards.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These defines are only used to initialize the diosubd_data 'addr' members
in the boardinfo. For aesthetics, just open-code the values and remove the
defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These defines are only used to initialize the diosubd_data 'addr' members
in the boardinfo. For aesthetics, just open-code the values and remove the
defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the board reset function also resets the digital output channels
to 0. This works but it makes the reset function a bit messy and each
board type has to be handled special.

Move the digital output reset into the subdevice init where it can be
handle based on the subdevice setup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The board reset function disables and clears all interrupts. It also
resets all the digital output channels to 0.

Interrupts are not currently used by this driver. For asthetics, do
the board reset early in the (*auto_attach) to make sure the interrupts
are disabled in case this feature is added.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The board reset function disables and clears all interrupts. It also
resets all the digital output channels to 0.

Interrupts are not used by this driver so the disable/clear during the
(*detach) is not necessary.

Reseting all the digital outputs to 0 might not be desired depending
on what the outputs are connected to.

Remove the board reset and just use comedi_pci_detach() directly for
the driver (*detach).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These defines are only used to initialize the diosubd_data 'addr' members
in the boardinfo. For aesthetics, just open-code the values and remove the
defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These defines are only used to initialize the 'timer_regbase' boardinfo.
For aesthetics, just open-code the values and remove the defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The "board id" register is always 4-bits (4 di channels) and the register
used to read the bits is always > 0.

Simplify the 'boardid' boardinfo by replacing it with a 'id_reg' member
and open-coding the subdevice n_chan.

For aesthetics, remove all the *_BOARDID defines and just open-code the
register values in the boardinfo.

Add the missing boardinfo for the pci1739 board id register and increase
the nsubdevs to handle it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the di/do subdevices store a pointer to the diosubd_data in s->private.
The (*insn_bits) functions then use that to get to the 'addr' needed to access
the registers.

The only member of diosubd_data that is needed by the (*insn_bits) functions is
the 'addr'. For aesthetics, just store the 'addr' in s->private.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the (*insn_bits) functions used the 'regs' member to determine how
many registers need to be read or written to update the subdevice. We can use
the subdevice 'n_chan' to determine this and make the code a bit clearer.

The (*auto_attach) also uses this member to determine how many 8255 devices
need to be initialized. These subdevices do not use the 'chans' member of
diosubd_data. Move the 'regs' value to the 'chans' to allow removing the
'regs' member completely.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The boards supported by this driver either use 8-bit or 16-bit I/O. The
'io_access' member of the boardinfo is used by the (*auto_attach) to
determine which (*insn_bits) function to use.

Simplify the boardinfo a bit by refactoring the 'io_access' member into
a bit-field flag 'is_16bit'. Use the new flag and remove the switch ()
code in the (*auto_attach).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function initializes a digitial input subdevices. For aesthetics,
absorb it into the (*auto_attach).

Remove the improper initialization of the SDF_LSAMPL subdev_flag and
len_chanlist. These are only used by subdevices that support async
commands.

Also, remove the unnecessary 'specflags' from the diosubd_data. Only
the boardid subdevice uses it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function initializes a digitial output subdevice. For aesthetics,
absorb it into the (*auto_attach).

Remove the improper initialization of the SDF_LSAMPL subdev_flag and
len_chanlist. These are only used by subdevices that support async
commands.

Also remove the unnecessary initilaization of the subdevice 'state'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, use a const pointer to access the diosubd_data in the
boardinfo when doing the (*auto_attach)..
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetics, post-increment the 'subdev' index when used to get a
comedi_subdevice pointer instead of incrementing it after the subdevice
is initialized.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All the boards use PCI BAR2 for the dev->iobase except for the pci1736
which uses PCI BAR0. Just use the board->cardtype to determine which
PCI BAR to use.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reformat the bolck comment in the kernel CodingStyle.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These are not necessary and just add cruft. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BIT macro is used for defining BIT location instead of
shifting operator - coding style issue
Signed-off-by: Ranjith Thangavel <ranjithece24@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ni_release_ai_mite_channel(), ni_release_ao_mite_channel(),
ni_release_gpct_mite_channel() and ni_release_cdo_mite_channel()
call functions which interpret -1 as a special value meaning "no channel".
This patch adds explicit "no_channel" versions instead.

On the other hand, after "no_channel" versions are used,
ni_set_ai_dma_channel(), ni_set_ao_dma_channel(),
ni_set_gpct_dma_channel(), ni_set_cdo_dma_channel() are called with actual
"channel" parameter being always unsigned, so their signatures are changed
accordingly.

A side benefit of the changes is suppressesing 4 sparse warnings:
"warning: shift too big (4294967295) for type int".
Signed-off-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed multiple comment blocks that didn't comply with the
kernels coding style, and fixed a few spacing issues as well.
Signed-off-by: Daniel H. Hemmingsen <dhh.kernel@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BIT macro is used for defining BIT location instead of
shifting operator - coding style issue
Signed-off-by: Ranjith Thangavel <ranjithece24@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BIT macro is used for defining BIT location instead of
shifting operator - coding style issue
Signed-off-by: Ranjith Thangavel <ranjithece24@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BIT macro is used for defining BIT location instead of
shifting operator - coding style issue
Signed-off-by: Ranjith Thangavel <ranjithece24@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kmalloc_array instead of kmalloc to allocate memory for an array.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch is to file dgnc_cls.c that fixes up udelay function by
usleep_range.
It is safe to use according to the following documentation
Documentation/timers/timers-howto.txt. So that is why I have given
an appropriate time range.
Signed-off-by: Jitendra Kumar Khasdev <jkhasdev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix Typo errror in the comment section of dgnc_wmove
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix Checlpatch warning
HECK: braces {} should be used on all arms of this statement
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes all "spaces preferred around that ..." messages from
checkpatch.pl
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The script "checkpatch.pl" pointed out that labels should not be indented.
Thus delete a horizontal tab before the jump label "out"
in the function "osc_get_info".
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable "mne_swab" will eventually be set to an appropriate value
from a call of the ptlrpc_rep_need_swab() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Six goto statements referred to a source code position
directly behind them.
Thus omit such unnecessary jumps.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lu_site_hash_ops is used only in this particular file. Thus declare
it as static.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

osc_attr_set is used only in this particular file. Thus declare it
as static.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare osc_extent_find and osc_unreserve_grant as static since they
are used only in this particular file.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Function libcfs_debug_set_level is defined but not used. Thus
remove it.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>