Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).

To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.

This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".

Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.

This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

A little bit of cleanup work for 'wacom_update_name' to make it easier on
the eyes. Creates a temporary 'name' variable on which we'll perform our
edits. Once the name is in its final form, it will be copied (with
appropriate suffix) to 'wacom_wac->name' and 'wacom_wac->pad_name'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Hardware may not respond to a request for the HID_DG_CONTACTMAX feature and
we should be tolerant of such a failure. This is especially true when using
hid-replay where the hardware doesn't exist, but also for devices attached
to a flaky bus. This patch increases the number of allowable retries to
match other calls to 'wacom_get_report' and also provides a fallback which
forces 'touch_max = 16' (enough for any Wacom device seen so far).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Retrying on -EPIPE makes very little sense since this typically indicates
a problem that will not just disappear on its own. For instance, the USB
documentation states that it will be sent if the endpoint is stalled or
the device has disconnected. Instead, we should retry if -EAGAIN is
received since this indicates a temporary error condition such as a busy
bus.

In addition to adjusting the conditions we retry under, we also log an
error on failure so that we can be aware of what's going on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The last patch was careful to maintain backwards-compatible behavior
by forcing device_type to BTN_TOOL_PEN (and printing a warning) if it
were still uninitialized after scanning the HID descriptor and applying
quirks. We should be more strict with HID_GENERIC devices, however,
since there is no a priori guarantee that it is a tablet or touchpad.
If the device_type is still uninitialized for a HID_GENERIC device then
we assume that it isn't something the driver can work with and so fail
the probe.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.

This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.

Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The naming logic currently assumes that all devices will be a pen, finger,
or pad. Though this has historically been the case, the new HID_GENERIC
catch-all may cause us to probe devices with Wacom's 056A VID which aren't
any of these types (e.g. the "Cintiq 24HDT Monitor Control"). This patch
updates the logic so that no suffix will be added to the device name if
the device type is unknown.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

HID generic devices share the same default name, "Wacom HID". This
causes userland programs to show same device names for different
devices, which would confuse end users with same device names for
different devices too.

This patch uses name retrieved from HID descriptor, if a meaningful
name is reported. Otherwise, affix its product ID to "Wacom HID".

Names from descriptor may contain extra whitespaces. To comfort
readers' eyes, we removed those extra whitespaces too.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

To determine if a touch is present in the single-touch case, we can
simply check if the BTN_TOUCH key is active or not. This will work for
both HID_GENERIC and other device types.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

We use generic hid_report_len() to get individual packet length now.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

That is where they belong...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

It makes probe routine easy to follow.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID updates from Jiri Kosina:

 - quite a few firmware fixes for RMI driver by Andrew Duggan

 - huion and uclogic drivers have been substantially overlaping in
   functionality laterly.  This redundancy is fixed by hid-huion driver
   being merged into hid-uclogic; work done by Benjamin Tissoires and
   Nikolai Kondrashov

 - i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg

 - Some of the quirks, that got separated into individual drivers, have
   historically had EXPERT dependency.  As HID subsystem matured (as
   well as the individual drivers), this made less and less sense.  This
   dependency is now being removed by patch from Jean Delvare

 - Logitech lg4ff driver received a couple of improvements for mode
   switching, by Michal Malý

 - multitouch driver now supports clickpads, patches by Benjamin
   Tissoires and Seth Forshee

 - hid-sensor framework received a substantial update; namely support
   for Custom and Generic pages is being added; work done by Srinivas
   Pandruvada

 - wacom driver received substantial update; it now supports
   i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
   properly supported (Benjamin Tissoires), much improved battery
   reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)

 - small assorted fixes and device ID additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
  HID: sensor: Update document for custom sensor
  HID: sensor: Custom and Generic sensor support
  HID: debug: fix error handling in hid_debug_events_read()
  Input - mt: Fix input_mt_get_slot_by_key
  HID: logitech-hidpp: fix error return code
  HID: wacom: Add support for Cintiq 13HD Touch
  HID: logitech-hidpp: add a module parameter to keep firmware gestures
  HID: usbhid: yet another mouse with ALWAYS_POLL
  HID: usbhid: more mice with ALWAYS_POLL
  HID: wacom: set stylus_in_proximity before checking touch_down
  HID: wacom: use wacom_wac_finger_count_touches to set touch_down
  HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
  HID: pidff: effect can't be NULL
  HID: add quirk for PIXART OEM mouse used by HP
  HID: add HP OEM mouse to quirk ALWAYS_POLL
  HID: wacom: ask for a in-prox report when it was missed
  HID: hid-sensor-hub: Fix sparse warning
  HID: hid-sensor-hub: fix attribute read for logical usage id
  HID: plantronics: fix Kconfig default
  HID: pidff: support more than one concurrent effect
  ...

Commit 297d716f ("power_supply: Change ownership from driver to
core") inverted the logic in battery_notify().  As an effect already
present battery was re-added on each system suspend or hibernation.

    WARNING: CPU: 0 PID: 303 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x68/0x80()
    sysfs: cannot create duplicate filename '/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0C0A:00/power_supply/BAT0'
    CPU: 0 PID: 303 Comm: rtcwake Not tainted 4.0.0-ARCH-02621-g07e6253af953 #48
    Call Trace:
      sysfs_create_dir_ns+0x8d/0xa0
      kobject_add_internal+0xb6/0x370
      kobject_add+0x6f/0xd0
      device_add+0x120/0x6c0
      __power_supply_register+0x145/0x290
      power_supply_register_no_ws+0x10/0x20
      sysfs_add_battery+0x84/0xc5 [battery]
      battery_notify+0x45/0x6b [battery]
      notifier_call_chain+0x4f/0x80
      __blocking_notifier_call_chain+0x4b/0x70
      blocking_notifier_call_chain+0x16/0x20
      pm_notifier_call_chain+0x1a/0x40
      pm_suspend+0x3ed/0x4e0
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull staging driver updates from Greg KH:
 "Here's the big staging driver patchset for 4.1-rc1.

  There's a lot of patches here, the Outreachy application period
  happened during this development cycle, so that means that there was a
  lot of cleanup patches accepted.  Other than the normal coding style
  and sparse fixes here, there are some driver updates and work toward
  making some of the drivers into "mergable" shape (like the Unisys
  drivers.)

  All of these have been in linux-next for a while"

* tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1214 commits)
  staging: lustre: orthography & coding style
  staging: lustre: lnet: lnet: fix error return code
  staging: lustre: fix sparse warning
  Revert "Staging: sm750fb: Fix C99 Comments"
  Staging: rtl8192u: use correct array for debug output
  staging: rtl8192e: Remove dead code
  staging: rtl8192e: Comment cleanup (style/format)
  staging: rtl8192e: Fix indentation in rtllib_rx_auth_resp()
  staging: rtl8192e: Decrease nesting of rtllib_rx_auth_resp()
  staging: rtl8192e: Divide rtllib_rx_auth()
  staging: rtl8192e: Fix PRINTK_WITHOUT_KERN_LEVEL warnings
  staging: rtl8192e: Fix DO_WHILE_MACRO_WITH_TRAILING_SEMICOLON warning
  staging: rtl8192e: Fix BRACES warning
  staging: rtl8192e: Fix LINE_CONTINUATIONS warning
  staging: rtl8192e: Fix UNNECESSARY_PARENTHESES warnings
  staging: rtl8192e: remove unused EXPORT_SYMBOL_RSL macro
  staging: rtl8192e: Fix RETURN_VOID warnings
  staging: rtl8192e: Fix UNNECESSARY_ELSE warning
  staging: rtl8723au: Remove unneeded comments
  staging: rtl8723au: Use __func__ in trace logs
  ...

Pull driver core updates from Greg KH:
 "Here's the driver-core / kobject / lz4 tree update for 4.1-rc1.

  Everything here has been in linux-next for a while with no reported
  issues.  It's mostly just coding style cleanups, with other minor
  changes in here as well, nothing big"

* tag 'driver-core-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
  debugfs: allow bad parent pointers to be passed in
  stable_kernel_rules: Add clause about specification of kernel versions to patch.
  kobject: WARN as tip when call kobject_get() to a kobject not initialized
  lib/lz4: Pull out constant tables
  drivers: platform: parse IRQ flags from resources
  driver core: Make probe deferral more quiet
  drivers/core/of: Add symlink to device-tree from devices with an OF node
  device: Add dev_of_node() accessor
  drivers: base: fw: fix ret value when loading fw
  firmware: Avoid manual device_create_file() calls
  drivers/base: cacheinfo: validate device node for all the caches
  drivers/base: use tabs where possible in code indentation
  driver core: add missing blank line after declaration
  drivers: base: node: Delete space after pointer declaration
  drivers: base: memory: Use tabs instead of spaces
  firmware_class: Fix whitespace and indentation
  drivers: base: dma-mapping: Erase blank space after pointer
  drivers: base: class: Add a blank line after declarations
  attribute_container: fix missing blank lines after declarations
  drivers: base: memory: Fix switch indent
  ...

Pull USB driver updates from Greg KH:
 "Here's the big USB (and PHY) driver patchset for 4.1-rc1.

  Everything here has been in linux-next, and the full details are below
  in the shortlog.  Nothing major, just the normal round of new
  drivers,api updates, and other changes, mostly in the USB gadget area,
  as usual"

* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
  drivers/usb/core: devio.c: Removed an uneeded space before tab
  usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
  usb: chipidea: debug: add low power mode check before print registers
  usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
  usb: core: hub: use new USB_RESUME_TIMEOUT
  usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
  usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
  usb: host: sl811: use new USB_RESUME_TIMEOUT
  usb: host: r8a66597: use new USB_RESUME_TIMEOUT
  usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
  usb: host: fusbh200: use new USB_RESUME_TIMEOUT
  usb: host: fotg210: use new USB_RESUME_TIMEOUT
  usb: host: isp116x: use new USB_RESUME_TIMEOUT
  usb: musb: use new USB_RESUME_TIMEOUT
  usb: host: uhci: use new USB_RESUME_TIMEOUT
  usb: host: ehci: use new USB_RESUME_TIMEOUT
  usb: host: xhci: use new USB_RESUME_TIMEOUT
  usb: define a generic USB_RESUME_TIMEOUT macro
  usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
  ehci-hub: use USB_DT_HUB
  ...

Pull cgroup updates from Tejun Heo:
 "Nothing too interesting.  Rik made cpuset cooperate better with
  isolcpus and there are several other cleanup patches"

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset, isolcpus: document relationship between cpusets & isolcpus
  cpusets, isolcpus: exclude isolcpus from load balancing in cpusets
  sched, isolcpu: make cpu_isolated_map visible outside scheduler
  cpuset: initialize cpuset a bit early
  cgroup: Use kvfree in pidlist_free()
  cgroup: call cgroup_subsys->bind on cgroup subsys initialization

Pull libata updates from Tejun Heo:

 - Hannes's patchset implements support for better error reporting
   introduced by the new ATA command spec.

 - the deperecated pci_ dma API usages have been replaced by dma_ ones.

 - a bunch of hardware specific updates and some cleanups.

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: remove deprecated use of pci api
  ahci: st: st_configure_oob must be called after IP is clocked.
  ahci: st: Update the ahci_st DT documentation
  ahci: st: Update the DT example for how to obtain the PHY.
  sata_dwc_460ex: indent an if statement
  libata: Add tracepoints
  libata-eh: Set 'information' field for autosense
  libata: Implement support for sense data reporting
  libata: Implement NCQ autosense
  libata: use status bit definitions in ata_dump_status()
  ide,ata: Rename ATA_IDX to ATA_SENSE
  libata: whitespace fixes in ata_to_sense_error()
  libata: whitespace cleanup in ata_get_cmd_descript()
  libata: use READ_LOG_DMA_EXT
  libata: remove ATA_FLAG_LOWTAG
  sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
  sata_dwc_460ex: move to generic DMA driver
  sata_dwc_460ex: join messages back
  sata: xgene: add ACPI support for APM X-Gene SATA ports
  ata: sata_mv: add proper definitions for LP_PHY_CTL register values

Pull workqueue updates from Tejun Heo:
 "Workqueue now prints debug information at the end of sysrq-t which
  should be helpful when tracking down suspected workqueue stalls.  It
  only prints out the ones with something currently going on so it
  shouldn't add much output in most cases"

* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Reorder sysfs code
  percpu: Fix trivial typos in comments
  workqueue: dump workqueues on sysrq-t
  workqueue: keep track of the flushing task and pool manager
  workqueue: make the workqueues list RCU walkable

Pull irq core updates from Thomas Gleixner:
 "Managerial summary:

  Core code:
   - final removal of IRQF_DISABLED
   - new state save/restore functions for virtualization support
   - wakeup support for stacked irqdomains
   - new function to solve the netpoll synchronization problem

 irqchips:
   - new driver for STi based devices
   - new driver for Vybrid MSCM
   - massive cleanup of the GIC driver by moving the GIC-addons to
     stacked irqdomains
   - the usual pile of fixes and updates to the various chip drivers"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
  irqchip: GICv3: Add support for irq_[get, set]_irqchip_state()
  irqchip: GIC: Add support for irq_[get, set]_irqchip_state()
  genirq: Allow the irqchip state of an IRQ to be save/restored
  genirq: MSI: Fix freeing of unallocated MSI
  irqchip: renesas-irqc: Add wake-up support
  irqchip: armada-370-xp: Allow using wakeup source
  irqchip: mips-gic: Add new functions to start/stop the GIC counter
  irqchip: tegra: Add Tegra210 support
  irqchip: digicolor: Move digicolor_set_gc to init section
  irqchip: renesas-irqc: Add functional clock to bindings
  irqchip: renesas-irqc: Add minimal runtime PM support
  irqchip: renesas-irqc: Add more register documentation
  DT: exynos: update PMU binding
  ARM: exynos4/5: convert pmu wakeup to stacked domains
  irqchip: gic: Don't complain in gic_get_cpumask() if UP system
  ARM: zynq: switch from gic_arch_extn to gic_set_irqchip_flags
  ARM: ux500: switch from gic_arch_extn to gic_set_irqchip_flags
  ARM: shmobile: remove use of gic_arch_extn.irq_set_wake
  irqchip: gic: Add an entry point to set up irqchip flags
  ARM: omap: convert wakeupgen to stacked domains
  ...

Pull PCI changes from Bjorn Helgaas:
 "Enumeration
    - Read capability list as dwords, not bytes (Sean O. Stalley)

  Resource management
    - Don't check for PNP overlaps with unassigned PCI BARs (Bjorn Helgaas)
    - Mark invalid BARs as unassigned (Bjorn Helgaas)
    - Show driver, BAR#, and resource on pci_ioremap_bar() failure (Bjorn Helgaas)
    - Fail pci_ioremap_bar() on unassigned resources (Bjorn Helgaas)
    - Assign resources before drivers claim devices (Yijing Wang)
    - Claim bus resources before pci_bus_add_devices() (Yijing Wang)

  Power management
    - Optimize device state transition delays (Aaron Lu)
    - Don't clear ASPM bits when the FADT declares it's unsupported (Matthew Garrett)

  Virtualization
    - Add ACS quirks for Intel 1G NICs (Alex Williamson)

  IOMMU
    - Add ptr to OF node arg to of_iommu_configure() (Murali Karicheri)
    - Move of_dma_configure() to device.c to help re-use (Murali Karicheri)
    - Fix size when dma-range is not used (Murali Karicheri)
    - Add helper functions pci_get[put]_host_bridge_device() (Murali Karicheri)
    - Add of_pci_dma_configure() to update DMA configuration (Murali Karicheri)
    - Update DMA configuration from DT (Murali Karicheri)
    - dma-mapping: limit IOMMU mapping size (Murali Karicheri)
    - Calculate device DMA masks based on DT dma-range size (Murali Karicheri)

  ARM Versatile host bridge driver
    - Check for devm_ioremap_resource() failures (Jisheng Zhang)

  Broadcom iProc host bridge driver
    - Add Broadcom iProc PCIe driver (Ray Jui)

  Marvell MVEBU host bridge driver
    - Add suspend/resume support (Thomas Petazzoni)

  Renesas R-Car host bridge driver
    - Fix position of MSI enable bit (Nobuhiro Iwamatsu)
    - Write zeroes to reserved PCIEPARL bits (Nobuhiro Iwamatsu)
    - Change PCIEPARL and PCIEPARH to PCIEPALR and PCIEPAUR (Nobuhiro Iwamatsu)
    - Verify that mem_res is 64K-aligned (Nobuhiro Iwamatsu)

  Samsung Exynos host bridge driver
    - Fix INTx enablement statement termination error (Jaehoon Chung)

  Miscellaneous
    - Make a shareable UUID for PCI firmware ACPI _DSM (Aaron Lu)
    - Clarify policy for vendor IDs in pci.txt (Michael S. Tsirkin)"

* tag 'pci-v4.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (36 commits)
  PCI: Read capability list as dwords, not bytes
  PCI: layerscape: Simplify platform_get_resource_byname() failure checking
  PCI: keystone: Don't dereference possible NULL pointer
  PCI: versatile: Check for devm_ioremap_resource() failures
  PCI: Don't clear ASPM bits when the FADT declares it's unsupported
  PCI: Clarify policy for vendor IDs in pci.txt
  PCI/ACPI: Optimize device state transition delays
  PCI: Export pci_find_host_bridge() for use inside PCI core
  PCI: Make a shareable UUID for PCI firmware ACPI _DSM
  PCI: Fix typo in Thunderbolt kernel message
  PCI: exynos: Fix INTx enablement statement termination error
  PCI: iproc: Add Broadcom iProc PCIe support
  PCI: iproc: Add DT docs for Broadcom iProc PCIe driver
  PCI: Export symbols required for loadable host driver modules
  PCI: Add ACS quirks for Intel 1G NICs
  PCI: mvebu: Add suspend/resume support
  PCI: Cleanup control flow
  sparc/PCI: Claim bus resources before pci_bus_add_devices()
  PCI: Assign resources before drivers claim devices (pci_scan_root_bus())
  PCI: Fail pci_ioremap_bar() on unassigned resources
  ...

Pull HSI changes from Sebastian Reichel:

 - nokia-modem: support speech data
 - misc fixes

* tag 'hsi-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  HSI: cmt_speech: fix error return code
  HSI: nokia-modem: Add cmt-speech support
  HSI: cmt_speech: Add cmt-speech driver
  HSI: nokia-modem: fix error return code

Pull power supply and reset changes from Sebastian Reichel:

 - new API for safe access of power supply function attrs

 - devres support for power supply (un)registration

 - new drivers / chips:
     - generic syscon based poweroff driver
     - iio & charger driver for da9150
     - fuel gauge driver for axp288
     - bq27x00: add support for bq27510
     - bq2415x: add support for bq24157s

 - twl4030-madc-battery: convert to iio consumer

 - misc fixes

* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
  power: twl4030_madc_battery: Add missing MODULE_ALIAS
  power: twl4030-madc-battery: Convert to iio consumer.
  dt: power: Add docs for generic SYSCON poweroff driver.
  power: reset: Add generic SYSCON register mapped poweroff.
  power: max17042_battery: add missed blank
  power: max17042_battery: Use reg type instead of chip type
  power/reset: at91: big endian fixes for atsama5d3x
  power_supply: charger-manager: Fix dereferencing of ERR_PTR
  HID: input: Fix NULL pointer dereference when power_supply_register fails
  power: constify of_device_id array
  power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
  power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
  arm: mach-pxa: Decrement the power supply's device reference counter
  mfd: ab8500: Decrement the power supply's device reference counter
  power_supply: bq2415x_charger: Decrement the power supply's device reference counter
  power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
  x86/olpc/xo15/sci: Use newly added power_supply_put API
  x86/olpc/xo1/sci: Use newly added power_supply_put API
  power_supply: charger-manager: Decrement the power supply's device reference counter
  power_supply: Increment power supply use counter when obtaining references
  ...

Pull regulator updates from Mark Brown:
 "Another release, another set of regulator updates.  Not much of it is
  showing up in the code yet but there's been a lot of discussion going
  on about how to enhance the regulator API to work better with modern
  SoCs which have a microcontroller sitting between Linux and the
  hardware.

  I'm hopeful that'll start to come through into mainline for v4.2 but
  it's not quite there for v4.1 - what we do have (along with the usual
  small updates is) is:

   - work from Bjorn Andersson on refactoring the configuration of
     regulator loading interfaces to be useful for use with
     microcontrollers, the existing interfaces were never actually
     useful for anything as-is since nobody was willing to put enough
     data into public code.

   - a summary tree display in debugfs from Heiko Stübner.

   - support for act6000 regulators"

* tag 'regulator-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (34 commits)
  regulator: max8660: Handle empty regulator data
  regulator: output current-limit for all regulators in summary
  regulator: add a summary tree in debugfs
  regulator: qcom: Tidy up probe()
  regulator: qcom: Rework to single platform device
  regulator: qcom: Refactor of-parsing code
  regulator: qcom: Don't enable DRMS in driver
  regulator: max8660: fix assignment of pdata to data that becomes dead
  regulator: Defer lookup of supply to regulator_get
  mfd: max77693: Remove unused structures
  regulator: max77693: Let core parse DT and drop board files support
  regulator: Ensure unique regulator debugfs directory names
  regulator: stw481x: Remove unused fields from struct stw481x
  regulator: palmas: Add has_regen3 check for TPS659038
  regulator: constify of_device_id array
  regulator: fixes for regulator_set_optimum_mode name change
  regulator: Drop temporary regulator_set_optimum_mode wrapper
  usb: phy: phy-msm-usb: Rename regulator_set_optimum_mode
  usb: phy: ab8500-usb: Rename regulator_set_optimum_mode
  ufs: Rename of regulator_set_optimum_mode
  ...

Pull spi updates from Mark Brown:
 "Only one framework update this time around, a change from Lars-Peter
  to move full to pm_ops and remove the legacy bus PM ops.  Otherwise
  it's all driver updates:

   - make the spidev driver complain loudly if registered as spidev with
     DT rather than with a compatible string, hopefully helping people
     avoid making that mistake.

   - error handling and robustness fixes for the Designware and Intel
     MID drivers from Andy Shevchenko.

   - substantial performance improvements for the Raspberry Pi driver
     from Martin Sperl.

   - several new features for spidev_test from Adrian Remonda and Ian
     Abbott"

* tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (75 commits)
  spi: bcm2835: enabling polling mode for transfers shorter than 30us
  spi: bcm2835: transform native-cs to gpio-cs on first spi_setup
  spi: img-spfi: Control CS lines with GPIO
  spi: img-spfi: Reset controller after each message
  spi: img-spfi: Implement a handle_err() callback
  spi: img-spfi: Setup TRANSACTION register before CONTROL register
  spi: Make master->handle_err() callback optional to avoid crashes
  spi: img-spfi: Limit bit clock to 1/4th of input clock
  spi: img-spfi: Implement a prepare_message() callback
  spi: fsl-dspi: Add ~50ns delay between cs and sck
  spi: fsl-dspi: Add cs-sck delays
  spi: fsl-dspi: Fix clock rate scale values
  spi: signedness bug in qspi_trigger_transfer_out_int()
  spi: imx: read back the RX/TX watermark levels earlier
  spi: spi-bfin5xx: Initialize cr_width in bfin_spi_pump_transfers()
  spi: bitbang: only toggle bitchanges
  spi: pxa2xx: missing break in pxa2xx_ssp_get_clk_div()
  spi: fsl-dspi: Fix clock rate scale values
  spi: Using Trigger number to transmit/receive data
  spi: bcm2835: fill FIFO before enabling interrupts to reduce interrupts/message
  ...

Pull regmap update from Mark Brown:
 "Just one patch for regmap this time around, a change from Steven
  Rostedt to prettify the way we're making the regmap internal header
  available to the trace events (it turns out that the trace subsystem
  doesn't actually need to be in trace/events)"

* tag 'regmap-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Move tracing header into drivers/base/regmap

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for marking HPI as broken through devicetree
   - Enable runtime PM management of host devices
   - Remove the ->enable|disable() callbacks
   - Restructure code and cleanups
   - Refreshed some of the MMC sections in MAINTAINERS

  MMC host:
   - dw_mmc: HS400 mode support
   - dw_mmc: Add the cmd11 timer to detect a timeout
   - dw_mmc: Endian agnostic IO accessors
   - dw_mmc: Bugfixes
   - sh_mmcif: Add exclusion between cmd and interrupt
   - omap_hsmmc: Hibernation support
   - omap_hsmmc: Rework and simplify cover/card detect
   - omap_hsmmc: Stop using ->enable|disable() callbacks
   - atmel-mci: Endian agnostic IO
   - sunxi: Enable MMC_CAP_SDIO_IRQ
   - sdhci-st: Add support for the stih407 family silicon
   - sdhci-st: UHS card support in SDR104 mode
   - sdhci-st: HS200 mode support
   - sdhci-esdhc-imx: Use common mmc DT parser
   - sdhci-of-arasan: Use common mmc DT parser
   - sdhci-iproc: Add new driver for Broadcom IPROC SDHCI controller
   - sdhci-tegra: Convert to GPIO descriptors
   - sdhci-tegra: Optmize write_w path for tegra114 and later
   - sdhci-sirf: Update tuning procedure
   - sdhci: Fix card presence logic
   - sdhci: Cleanups and consolidation"

* tag 'mmc-v4.1' of git://git.linaro.org/people/ulf.hansson/mmc: (79 commits)
  mmc: sdhci-st: Update ST SDHCI binding documentation.
  mmc: sdhci-st: Update the quirks for this controller.
  mmc: sdhci-st: Add sdhci_st_set_uhs_signaling function.
  mmc: sdhci-st: Add st_mmcss_cconfig function to configure mmcss glue registers.
  mmc: sdhci-st: Add delay management functions for top registers (eMMC).
  mmc: sdhci-st: Add support for de-asserting reset signal and top regs resource
  mmc: sdhci-st: Add macros for register offsets and bitfields for mmcss glue regs
  mmc: sdhci-esdhc-imx: Call mmc_of_parse()
  mmc: dw_mmc: Add locking around cmd11 timer
  mmc: dw_mmc: Add a return in an unexpected cmd11 timeout
  mmc: dw_mmc: Increase cmd11 timeout to 500ms
  mmc: dw_mmc: fix fifo ordering in big endian
  mmc: dw_mmc: change idmac descriptor files to __le32
  mmc: dw_mmc: make IO accessors endian agnostic
  mmc: core: Convert the error field in struct mmc_command|data into an int
  mmc: sdhci-of-arasan: Call OF parsing for MMC
  mmc: sdhci-pci: fix 64 BIT DMA quirks for rtsx
  mmc: Add support for marking hpi as broken through devicetree
  mmc: sdhci-tegra: convert to use GPIO descriptors
  mmc: omap_hsmmc: use generic slot-gpio isr to manage card detect pin
  ...

Pull EDAC updates from Borislav Petkov:

 - convert a bunch of drivers to static attribute groups (Takashi Iwai)

 - misc cleanups

* tag 'edac_for_4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Constify of_device_id array
  EDAC, i82443bxgx: Don't export static symbol
  EDAC, amd64_edac: Get rid of per-node driver instances
  EDAC: Properly unwind on failure path in edac_init()
  EDAC: highbank: Use static attribute groups for sysfs entries
  EDAC: octeon: Use static attribute groups for sysfs entries
  EDAC: mpc85xx: Use static attribute groups for sysfs entries
  EDAC: i7core: Use static attribute groups for sysfs entries
  EDAC: i7core: Return proper error codes for kzalloc() errors
  EDAC: amd64: Use static attribute groups
  EDAC: Allow to pass driver-specific attribute groups
  EDAC: Use static attribute groups for managing sysfs entries
  EDAC: Delete unnecessary checks before pci_dev_put()

Conflicts:
	drivers/iio/common/hid-sensors/hid-sensor-trigger.c
	include/linux/hid-sensor-hub.h

Merge branches 'for-4.0/upstream-fixes', 'for-4.1/genius', 'for-4.1/huion-uclogic-merge', 'for-4.1/i2c-hid', 'for-4.1/kconfig-drop-expert-dependency', 'for-4.1/logitech', 'for-4.1/multitouch', 'for-4.1/rmi', 'for-4.1/sony', 'for-4.1/upstream' and 'for-4.1/wacom' into for-linus

Merge tag 'hwmon-for-linus-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "Support for new chips:

   - add support for IT8620E, IT8781F, IT8786E, and IT8790E to it87
     driver

   - add driver for NCT7904

  Functional improvements:

   - support for new devicetree structure in ibmpowernv driver

   - register pwm-fan and gpio-fan drivers as thermal cooling devices

   - various minor cleanup and improvements to it87, nct6775, jc42,
     ibmpex, and coretemp drivers"

* tag 'hwmon-for-linus-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (43 commits)
  hwmon: (pwm-fan) Update the duty cycle inorder to control the pwm-fan
  hwmon: (it87) Use feature macros on sio_data
  hwmon: (ibmpowernv) Fix build error seen for some configurations
  hwmon: (gpio-fan) Move the thermal registration after registration is complete
  hwmon: (ibmpowernv) pretty print labels
  hwmon: (ibmpowernv) add a label attribute
  hwmon: (ibmpowernv) add support for the new device tree
  hwmon: (ibmpowernv) add a helper routine create_hwmon_attr
  hwmon: (it87) Add support for 6th fan of IT8620E
  hwmon: (it87) Add support for IT8620E
  hwmon: (it87) Add support for IT8790E
  hwmon: (it87) Introduce feature flag to reflect internal in7 sensor
  hwmon: (it87) Introduce configuration field for chip suffix
  hwmon: (it87) Fix PWM frequency display for chips with newer PWM control
  hwmon: (it87) Fix pwm sysfs attribute removal
  hwmon: (ibmpowernv) do not use the OPAL index for hwmon attribute names
  hwmon: (ibmpowernv) change create_hwmon_attr_name() prototype
  hwmon: (ibmpowernv) add a convert_opal_attr_name() routine
  hwmon: (ibmpowernv) add a get_sensor_type() routine
  hwmon: (ibmpowernv) replace AMBIENT_TEMP by TEMP
  ...

Pull avr32 fix from Hans-Christian Egtvedt.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  avr32: fix integer overflow in ELF_ET_DYN_BASE

Pull m68k updates from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/mac: Fix out-of-bounds array index in OSS IRQ source initialization
  m68k/pci: Remove a superflous KERN_ERR
  m68k/defconfig: Update defconfigs for v4.0-rc1
  m68k/q40: Make NE2000 builtin instead of modular
  m68k: Remove FSF address

Pull x86 vdso changes from Ingo Molnar:
 "Misc vDSO updates"

* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Remove x32 intermediates during 'make clean'
  x86/vdso: Teach 'make clean' to remove generated vdso-image-*.c files
  x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
  x86/vdso: Fix the x86 vdso2c tool includes

Pull x86 fix from Ingo Molnar:
 "Leftover from 4.0

  Fix a local stack variable corruption with certain kdump usage
  patterns (Dave Young)"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/numa: Fix kernel stack corruption in numa_init()->numa_clear_kernel_node_hotplug()

Pull x86 RAS changes from Ingo Molnar:
 "The main changes in this cycle were:

   - Simplify the CMCI storm logic on Intel CPUs after yet another
     report about a race in the code (Borislav Petkov)

   - Enable the MCE threshold irq on AMD CPUs by default (Aravind
     Gopalakrishnan)

   - Add AMD-specific MCE-severity grading function.  Further error
     recovery actions will be based on its output (Aravind Gopalakrishnan)

   - Documentation updates (Borislav Petkov)

   - ... assorted fixes and cleanups"

* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce/severity: Fix warning about indented braces
  x86/mce: Define mce_severity function pointer
  x86/mce: Add an AMD severities-grading function
  x86/mce: Reindent __mcheck_cpu_apply_quirks() properly
  x86/mce: Use safe MSR accesses for AMD quirk
  x86/MCE/AMD: Enable thresholding interrupts by default if supported
  x86/MCE: Make mce_panic() fatal machine check msg in the same pattern
  x86/MCE/intel: Cleanup CMCI storm logic
  Documentation/acpi/einj: Correct and streamline text
  x86/MCE/AMD: Drop bogus const modifier from AMD's bank4_names()

Pull x86 platform change from Ingo Molnar:
 "An Intel Quark SoC fix"

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel/quark: Run IMR self-test on IMR capble hw only