- 22 Nov, 2012 7 commits
-
-
Laurent Pinchart authored
v4l2_subdev_link_validate_get_format() retrieves the remote pad format depending on the entity type and prints a warning if the entity type is not supported. The type check doesn't take the subtype into account, and thus always prints a warning for device node types, even when supported. Fix it. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Anatolij Gustschin authored
Set "y_skip_top" to zero and revise comment as I do not see this line corruption on two different mt9v022 setups. The first read-out line is perfectly fine. Add mt9v022 platform data configuring y_skip_top for platforms that have issues with the first read-out line. Set y_skip_top to 1 for pcm990 board. Signed-off-by:
Anatolij Gustschin <agust@denx.de> Acked-by:
Eric Miao <eric.y.miao@gmail.com> Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Anatolij Gustschin authored
Some camera systems cannot operate mt9v022 in normal mode and use only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024 (TN-09-225) describes required register settings when configuring the snapshot operation. The snapshot mode requires that certain automatic functions of the image sensor should be disabled or set to fixed values. According to the TechNote bit 2 and bit 9 in the register 0x20 must be set in snapshot mode and unset for normal operation. This applies for mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on sensor chip version. Signed-off-by:
-
Anatolij Gustschin authored
Add controls for horizontal and vertical blanking. Also add an error message for case that the control handler init failed. Since setting the blanking registers is done by controls now, we shouldn't change these registers outside of the control function. Use v4l2_ctrl_s_ctrl() to set them. Signed-off-by:
-
Frank Schäfer authored
This is the result of experimenting with the SpeedLink VAD Laplace webcam. The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by analyzing USB-logs of this device running on MS Windows. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Anatolij Gustschin authored
Try reading on video device. If the camera bus driver supports reading we can try it and return the result. Also add a debug line. Signed-off-by:
-
Shawn Guo authored
The mx1_camera driver has been broken for a few release cycles since commit 6bd08127 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c). It seems there is no one even compile tested it since then, as doing so will end up with the following error. CC drivers/media/platform/soc_camera/mx1_camera.o In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0: arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory It seems there is no one being interested in bringing it back to work [1] so far. Let's mark it BROKEN. [1] https://lkml.org/lkml/2012/2/9/171Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
- 21 Nov, 2012 31 commits
-
-
Alan Cox authored
Missing break Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Alan Cox authored
This should have break statements in it. Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Shubhrajyoti D authored
Convert the struct i2c_msg initialization to C99 format. This makes maintaining and editing the code simpler. Also helps once other fields like transferred are added in future. Signed-off-by:
Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Sean Young authored
The winbond hardware has a counter for leading edges, which increases as they are received. As we read raw IR from a fifo in an interrupt handler, we cannot correlate them to specific IR pulses so we simply count all pulses and edges until we go idle and disable the receiver. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
This is needed for carrier reporting. Signed-off-by:
-
Sean Young authored
The receiver is never disabled by idle mode since rxstate never gets set to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR activity ends. Note that ir_raw_event_reset() already calls ir_raw_event_handle(). Signed-off-by:
-
Ezequiel Garcia authored
The sparse warning is: "drivers/media/usb/stkwebcam/stk-webcam.c:59:5: warning: symbol 'first_init' was not declared. Should it be static?" Declare variable 'first_init' as static and local to the function. Found by Hans Verkuil's daily build. Tested by compilation only. Signed-off-by:
Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by:
-
Sean Young authored
Signed-off-by:
-
Lad, Prabhakar authored
This patch adds an entry in MAINTAINERS file for TI Davinci media drivers. Signed-off-by:
Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
-
Alexey Klimov authored
This patch adds MAINTAINERS entry for radio-mr800 usb radio driver. Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Signed-off-by:
-
Sylwester Nawrocki authored
Signed-off-by:
Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by:
-
Sakari Ailus authored
And the smiapp-pll which is in a way part of the smiapp driver. Signed-off-by:
-
Murali Karicheri authored
As a first step towards migrating davinci platforms to use common clock framework, replace all instances of clk_enable() with clk_prepare_enable() and clk_disable() with clk_disable_unprepare(). Also fixes some issues related to clk clean up in the driver Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Acked-by:
-
Lad, Prabhakar authored
set device_caps and also change the driver and bus_info to proper values as per standard. Signed-off-by:
-
Lad, Prabhakar authored
This patch migrates VPBE display driver to videobuf2 framework. Signed-off-by:
-
Lad, Prabhakar authored
Warnings were generated because of the following commit changed data type for address pointer 195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors add __iomem annotation to fix following warnings drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’: drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default] arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile void *’ but argument is of type ‘long unsigned int’ This patch stores the ioremap_nocache() returned address in a void __iomem * instead of a unsigned long and passes the same to readl/writel functions which fixes the above warnings. Signed-off-by:
-
Sakari Ailus authored
Update contact information to correspond my e-mail address changes. Signed-off-by:
-
YAMANE Toshiaki authored
fixed below checkpatch warning. - WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ... - WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by:
YAMANE Toshiaki <yamanetoshi@gmail.com> Signed-off-by:
-
YAMANE Toshiaki authored
fixed below checkpatch warnings. - WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... - WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ... Signed-off-by:
-
YAMANE Toshiaki authored
fixed below checkpatch error. - ERROR: that open brace { should be on the previous line Signed-off-by: -
YAMANE Toshiaki authored
fixed below checkpatch warnings. - WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... - WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ... Signed-off-by:
-
YAMANE Toshiaki authored
fixed below checkpatch error. - ERROR: that open brace { should be on the previous line Signed-off-by: -
YAMANE Toshiaki authored
fixed below checkpatch warnings. - WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ... - WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by:
Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by:
-
YAMANE Toshiaki authored
fixed below checkpatch error. - ERROR: that open brace { should be on the previous line Signed-off-by: -
Hans de Goede authored
Reported through: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1046608 https://bugzilla.kernel.org/show_bug.cgi?id=48111Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Frank Schäfer authored
Currently used registers 0xc5 and 0xc7 provide only a very coarse adjustment possibility within a very small value range (0-3). With registers 0x01 and 0x03, a fine grained adjustment with 255 steps is possible. This is also what the Windows driver does. Signed-off-by:
-
Frank Schäfer authored
R,G,B balance registers are 0x01-0x03 instead of 0x02-0x04, which lead to the wrong conclusion that values are inverted. Exposure is controlled via page 3 registers and this is already documented. Also fix a whitespace issue. Signed-off-by:
-
Ezequiel Garcia authored
Many people are trying to use stk1160 on low memory devices. Instead of failing if one allocation fails, we allow the driver to continue working if fewer transfer buffers are available. Signed-off-by:
-
- 14 Nov, 2012 1 commit
-
-
Kirill Smelkov authored
Usage of TSTAMP_* macros has gone in 2010 in 730947bc (V4L/DVB: vivi: clean up and a major overhaul) but the macros remain. Say goodbye to them. Signed-off-by:
Kirill Smelkov <kirr@mns.spb.ru> Signed-off-by:
-
- 13 Nov, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
As reported by Stephen: After merging the v4l-dvb tree, today's linux-next build (x86_64 allmodconfig) failed like this: ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined! ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined! ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined! The smsir file should be part of the smsmdtv core, if RC is defined. Fix it. Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
