Jean-Louis reported a TCP regression and bisected to recent SACK
compression.

After a loss episode (receiver not able to keep up and dropping
packets because its backlog is full), linux TCP stack is sending
a single SACK (DUPACK).

Sender waits a full RTO timer before recovering losses.

While RFC 6675 says in section 5, "Algorithm Details",

   (2) If DupAcks < DupThresh but IsLost (HighACK + 1) returns true --
       indicating at least three segments have arrived above the current
       cumulative acknowledgment point, which is taken to indicate loss
       -- go to step (4).
...
   (4) Invoke fast retransmit and enter loss recovery as follows:

there are old TCP stacks not implementing this strategy, and
still counting the dupacks before starting fast retransmit.

While these stacks probably perform poorly when receivers implement
LRO/GRO, we should be a little more gentle to them.

This patch makes sure we do not enable SACK compression unless
3 dupacks have been sent since last rcv_nxt update.

Ideally we should even rearm the timer to send one or two
more DUPACK if no more packets are coming, but that will
be work aiming for linux-4.21.

Many thanks to Jean-Louis for bisecting the issue, providing
packet captures and testing this patch.

Fixes: 5d9f4262 ("tcp: add SACK compression")
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet is trapped and the corresponding SKB marked as
already-forwarded, it retains this marking even after it is forwarded
across veth links into another bridge. There, since it ingresses the
bridge over veth, which doesn't have offload_fwd_mark, it triggers a
warning in nbp_switchdev_frame_mark().

Then nbp_switchdev_allowed_egress() decides not to allow egress from
this bridge through another veth, because the SKB is already marked, and
the mark (of 0) of course matches. Thus the packet is incorrectly
blocked.

Solve by resetting offload_fwd_mark() in skb_scrub_packet(). That
function is called from tunnels and also from veth, and thus catches the
cases where traffic is forwarded between bridges and transformed in a
way that invalidates the marking.

Fixes: 6bc506b4 ("bridge: switchdev: Add forward mark support for stacked devices")
Fixes: abf4bb6b ("skbuff: Add the offload_mr_fwd_mark field")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

after 'police' configuration parameters were converted to use RCU instead
of spinlock, the state variables used to compute the traffic rate (namely
'tcfp_toks', 'tcfp_ptoks' and 'tcfp_t_c') are erroneously read/updated in
the traffic path without any protection.

Use a dedicated spinlock to avoid race conditions on these variables, and
ensure proper cache-line alignment. In this way, 'police' is still faster
than what we observed when 'tcf_lock' was used in the traffic path _ i.e.
reverting commit 2d550dba ("net/sched: act_police: don't use spinlock
in the data path"). Moreover, we preserve the throughput improvement that
was obtained after 'police' started using per-cpu counters, when 'avrate'
is used instead of 'rate'.

Changes since v1 (thanks to Eric Dumazet):
- call ktime_get_ns() before acquiring the lock in the traffic path
- use a dedicated spinlock instead of tcf_lock
- improve cache-line usage

Fixes: 2d550dba ("net/sched: act_police: don't use spinlock in the data path")
Reported-and-suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>

Meanwhile I know the driver quite well and I refactored bigger parts
of it. As a result people contact me already with r8169 questions.
Therefore I'd volunteer to become co-maintainer of the driver also
officially.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During tcp coalescing ensure that the skb hardware timestamp refers to the
highest sequence number data.
Previously only the software timestamp was updated during coalescing.
Signed-off-by: Stephen Mallon <stephen.mallon@sydney.edu.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-11-19

The following fixes are for mlx5 core and netdev driver.

For -stable v4.16
bc7fda7d4637 ('net/mlx5e: IPoIB, Reset QP after channels are closed')

For -stable v4.17
36917a270395 ('net/mlx5: IPSec, Fix the SA context hash key')

For -stable v4.18
6492a432be3a ('net/mlx5e: Always use the match level enum when parsing TC rule match')
c3f81be236b1 ('net/mlx5e: Removed unnecessary warnings in FEC caps query')
c5ce2e736b64 ('net/mlx5e: Fix selftest for small MTUs')

For -stable v4.19
effcd896b25e ('net/mlx5e: Adjust to max number of channles when re-attaching')
394cbc5acd68 ('net/mlx5e: RX, verify received packet size in Linear Striding RQ')
447cbb3613c8 ('net/mlx5e: Don't match on vlan non-existence if ethertype is wildcarded')
c223c1574612 ('net/mlx5e: Claim TC hw offloads support only under a proper build config')

Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.

Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Denis Bolotin says:

====================
qed: Fix Queue Manager getters

This patch series fixes various queue manager getter functions. It is
important to make sure the getter's caller will receive a valid queue even
in error case to prevent more serious bugs.
Please consider applying to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The getter callers doesn't know the valid Physical Queues (PQ) values.
This patch makes sure that a valid PQ will always be returned.

The patch consists of 3 fixes:

 - When qed_init_qm_get_idx_from_flags() receives a disabled flag, it
   returned PQ 0, which can potentially be another function's pq. Verify
   that flag is enabled, otherwise return default start_pq.

 - When qed_init_qm_get_idx_from_flags() receives an unknown flag, it
   returned NULL and could lead to a segmentation fault. Return default
   start_pq instead.

 - A modulo operation was added to MCOS/VFS PQ getters to make sure the
   PQ returned is in range of the required flag.

Fixes: b5a9ee7c ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the condition which verifies that only one flag is set. The API
bitmap_weight() should receive size in bits instead of bytes.

Fixes: b5a9ee7c ("qed: Revise QM cofiguration")
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If FEC caps query fails when executing 'ethtool <interface>'
the whole callback fails unnecessarily, fixed that by replacing the
error return code with debug logging only.

Fixes: 6cfa9460 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.

Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This bug would result in reading wrong FEC capabilities for 10G/40G.

Fixes: 2095b264 ("net/mlx5e: Add port FEC get/set functions")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Some speeds don't support turning FEC policy off. In case a requested
FEC policy is not supported for a speed (including current speed), its new
FEC policy would be:
	no FEC - if disabling FEC is supported for that speed
	unchanged - else

Fixes: 2095b264 ("net/mlx5e: Add port FEC get/set functions")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Arthur Kiyanovski says:

====================
net: ena: hibernation and rmmod bug fixes

This patchset includes 2 bug fixes:
1. A fix to a crash during resume from hibernation.
2. A fix to an illegal memory access during driver removal (e.g. during rmmod)
   which might cause a crash in certain systems.

The subminor number in the driver version is also promoted to indicate driver
was changed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update driver version due to critical bug fixes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ena_remove() we have the following stack call:
ena_remove()
  unregister_netdev()
  ena_destroy_device()
    netif_carrier_off()

Calling netif_carrier_off() causes linkwatch to try to handle the
link change event on the already unregistered netdev, which leads
to a read from an unreadable memory address.

This patch switches the order of the two functions, so that
netif_carrier_off() is called on a regiestered netdev.

To accomplish this fix we also had to:
1. Remove the set bit ENA_FLAG_TRIGGER_RESET
2. Add a sanitiy check in ena_close()
both to prevent double device reset (when calling unregister_netdev()
ena_close is called, but the device was already deleted in
ena_destroy_device()).
3. Set the admin_queue running state to false to avoid using it after
device was reset (for example when calling ena_destroy_all_io_queues()
right after ena_com_dev_reset() in ena_down)

Fixes: 944b28aa ("net: ena: fix missing lock during device destruction")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During resume from hibernation if ena_restore_device fails,
ena_com_dev_reset() is called, and uses the readless read mechanism,
which was already destroyed by the call to
ena_com_mmio_reg_read_request_destroy(). This causes a NULL pointer
reference.

In this commit we switch the call order of the above two functions
to avoid this crash.

Fixes: d7703ddb ("net: ena: fix rare bug when failed restart/resume is followed by driver removal")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different from processing the addstrm_out request, The receiver handles
an addstrm_in request by sending back an addstrm_out request to the
sender who will increase its stream's in and incnt later.

Now stream->incnt has been increased since it sent out the addstrm_in
request in sctp_send_add_streams(), with the wrong stream->incnt will
even cause crash when copying stream info from the old stream's in to
the new one's in sctp_process_strreset_addstrm_out().

This patch is to fix it by simply removing the stream->incnt change
from sctp_send_add_streams().

Fixes: 242bd2d5 ("sctp: implement sender-side procedures for Add Incoming/Outgoing Streams Request Parameter")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.

Fixes: d605d668 ("net/mlx5e: Add support for ethtool self diagnostics test")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In case of striding RQ, we use  MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU.  In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.

Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.

As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).

Fixes: 619a8f2a ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The mirror and not the output count is the one denoting a split.
Fix to condition the offload attempt on the mirror count being > 0
along the firmware to have the related capability.

Fixes: 592d3651 ("net/mlx5e: Parse mirroring action for offloaded TC eswitch flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Yossi Kuperman <yossiku@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When core driver enters deattach/attach flow after pci reset,
Number of logical CPUs may have changed.
As a result we need to update the cpu affiliated resource tables.
	1. indirect rqt list
	2. eq table

Reproduction (PowerPC):
	echo 1000 > /sys/kernel/debug/powerpc/eeh_max_freezes
	ppc64_cpu --smt=on
	# Restart driver
	modprobe -r ... ; modprobe ...
	# Link up
	ifconfig ...
	# Only physical CPUs
	ppc64_cpu --smt=off
	# Inject PCI errors so PCI will reset - calling the pci error handler
	echo 0x8000000000000000 > /sys/kernel/debug/powerpc/<PCI BUS>/err_injct_inboundA

Call trace when trying to add non-existing rqs to an indirect rqt:
	mlx5e_redirect_rqt+0x84/0x260 [mlx5_core] (unreliable)
	mlx5e_redirect_rqts+0x188/0x190 [mlx5_core]
	mlx5e_activate_priv_channels+0x488/0x570 [mlx5_core]
	mlx5e_open_locked+0xbc/0x140 [mlx5_core]
	mlx5e_open+0x50/0x130 [mlx5_core]
	mlx5e_nic_enable+0x174/0x1b0 [mlx5_core]
	mlx5e_attach_netdev+0x154/0x290 [mlx5_core]
	mlx5e_attach+0x88/0xd0 [mlx5_core]
	mlx5_attach_device+0x168/0x1e0 [mlx5_core]
	mlx5_load_one+0x1140/0x1210 [mlx5_core]
	mlx5_pci_resume+0x6c/0xf0 [mlx5_core]

Create cq will fail when trying to use non-existing EQ.

Fixes: 89d44f0a ("net/mlx5_core: Add pci error handlers to mlx5_core driver")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.

This worked accidentally b/c both enums have the same numerical values.

Fixes: d708f902 ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, we are only supporting tc hw offloads when the eswitch
support is compiled in, but we are not gating the adevertizment
of the NETIF_F_HW_TC feature on this config being set.

Fix it, and while doing that, also avoid dealing with the feature
on ethtool when the config is not set.

Fixes: e8f887ac ('net/mlx5e: Introduce tc offload support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

For the "all" ethertype we should not care whether the packet has
vlans. Besides being wrong, the way we did it caused FW error
for rules such as:

tc filter add dev eth0 protocol all parent ffff: \
	prio 1 flower skip_sw action drop

b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec)
wasn't set. Fix that by matching on vlan non-existence only if we were
also told to match on the ethertype.

Fixes: cee26487 ('net/mlx5e: Set vlan masks for all offloaded TC rules')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.

The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.

Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.

Fixes: dae37456 ("net/mlx5: Support for attaching multiple underlay QPs to root flow table")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.

This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.

Fixes: d6c4f029 ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This reverts commit 22d7be26.

The dst's mtu in transport can be updated by a non sctp place like
in xfrm where the MTU information didn't get synced between asoc,
transport and dst, so it is still needed to do the pmtu check
in sctp_packet_config.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As rfc7496#section4.5 says about SCTP_PR_SUPPORTED:

   This socket option allows the enabling or disabling of the
   negotiation of PR-SCTP support for future associations.  For existing
   associations, it allows one to query whether or not PR-SCTP support
   was negotiated on a particular association.

It means only sctp sock's prsctp_enable can be set.

Note that for the limitation of SCTP_{CURRENT|ALL}_ASSOC, we will
add it when introducing SCTP_{FUTURE|CURRENT|ALL}_ASSOC for linux
sctp in another patchset.

v1->v2:
  - drop the params.assoc_id check as Neil suggested.

Fixes: 28aa4c26 ("sctp: add SCTP_PR_SUPPORTED on sctp sockopt")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp increases sk_wmem_alloc by 1 when doing set_owner_w for the
skb allocked in sctp_packet_transmit and decreases by 1 when freeing
this skb.

But when this skb goes through networking stack, some subcomponents
might change skb->truesize and add the same amount on sk_wmem_alloc.
However sctp doesn't know the amount to decrease by, it would cause
a leak on sk->sk_wmem_alloc and the sock can never be freed.

Xiumei found this issue when it hit esp_output_head() by using sctp
over ipsec, where skb->truesize is added and so is sk->sk_wmem_alloc.

Since sctp has used sk_wmem_queued to count for writable space since
Commit cd305c74 ("sctp: use sk_wmem_queued to check for writable
space"), it's ok to fix it by counting sk_wmem_alloc by skb truesize
in sctp_packet_transmit.

Fixes: cac2661c ("esp4: Avoid skb_cow_data whenever possible")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myself as third phylib maintainer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix some potentially uninitialized variables and use-after-free in
    kvaser_usb can drier, from Jimmy Assarsson.

 2) Fix leaks in qed driver, from Denis Bolotin.

 3) Socket leak in l2tp, from Xin Long.

 4) RSS context allocation fix in bnxt_en from Michael Chan.

 5) Fix cxgb4 build errors, from Ganesh Goudar.

 6) Route leaks in ipv6 when removing exceptions, from Xin Long.

 7) Memory leak in IDR allocation handling of act_pedit, from Davide
    Caratti.

 8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.

 9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
    Sabrina Dubroca.

10) When NAPI cached skb is reused, we must set it to the proper initial
    state which includes skb->pkt_type. From Eric Dumazet.

11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.

12) Set RX queue properly in various tuntap receive paths, from Matthew
    Cover.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
  tuntap: fix multiqueue rx
  ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
  tipc: don't assume linear buffer when reading ancillary data
  tipc: fix lockdep warning when reinitilaizing sockets
  net-gro: reset skb->pkt_type in napi_reuse_skb()
  tc-testing: tdc.py: Guard against lack of returncode in executed command
  tc-testing: tdc.py: ignore errors when decoding stdout/stderr
  ip_tunnel: don't force DF when MTU is locked
  MAINTAINERS: Add entry for CAKE qdisc
  net: bridge: fix vlan stats use-after-free on destruction
  socket: do a generic_file_splice_read when proto_ops has no splice_read
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  net/sched: act_pedit: fix memory leak when IDR allocation fails
  net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
  ipv6: fix a dst leak when removing its exception
  net: mvneta: Don't advertise 2.5G modes
  drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
  net/mlx4: Fix UBSAN warning of signed integer overflow
  ...

When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.

Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.

The rx traffic can be generated by either of the following.
  1. a simple tap program which spins up multiple queues and writes packets
     to each of the file descriptors
  2. tx from a qemu vm with a tap multiqueue netdev

The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
  1. a simple netmap program which opens and reads from per-queue
     descriptors
  2. configuring RPS and doing per-cpu captures with rxtxcpu

Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.

Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "A small batch of fixes for v4.20-rc3.

  The overflow continuation fix addresses something that has been broken
  for several releases. Arguably it could wait even longer, but it's a
  one line fix and this finishes the last of the known address range
  scrub bug reports. The revert addresses a lockdep regression. The unit
  tests are not critical to fix, but no reason to hold this fix back.

  Summary:

   - Address Range Scrub overflow continuation handling has been broken
     since it was initially merged. It was only recently that error
     injection and platform-BIOS support enabled this corner case to be
     exercised.

   - The recent attempt to provide more isolation for the kernel Address
     Range Scrub state machine from userapace initiated sessions
     triggers a lockdep report. Revert and try again at the next merge
     window.

   - Fix a kasan reported buffer overflow in libnvdimm unit test
     infrastrucutre (nfit_test)"

* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  Revert "acpi, nfit: Further restrict userspace ARS start requests"
  acpi, nfit: Fix ARS overflow continuation
  tools/testing/nvdimm: Fix the array size for dimm devices.

Merge misc fixes from Andrew Morton:
 "16 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
  mm, page_alloc: check for max order in hot path
  scripts/spdxcheck.py: make python3 compliant
  tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
  lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
  mm/vmstat.c: fix NUMA statistics updates
  mm/gup.c: fix follow_page_mask() kerneldoc comment
  ocfs2: free up write context when direct IO failed
  scripts/faddr2line: fix location of start_kernel in comment
  mm: don't reclaim inodes with many attached pages
  mm, memory_hotplug: check zone_movable in has_unmovable_pages
  mm/swapfile.c: use kvzalloc for swap_info_struct allocation
  MAINTAINERS: update OMAP MMC entry
  hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
  kernel/sched/psi.c: simplify cgroup_move_task()
  z3fold: fix possible reclaim races

Pull scheduler fix from Ingo Molnar:
 "Fix an exec() related scalability/performance regression, which was
  caused by incorrectly calculating load and migrating tasks on exec()
  when they shouldn't be"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix cpu_util_wake() for 'execl' type workloads