From Shawn Guo:
mxs soc changes for 3.9

 - A couple of optimization on timer
 - Some updates on mxs_defconfig

* tag 'mxs-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
  ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
  ARM: mxs: use apbx bus clock to drive the timers on timrotv2
  ARM: mxs: Update mxs_defconfig

Add a couple of fixes sent via email (via Stephen/Hiroshi).

* tegra/t114:
  ARM: tegra: sort Kconfig selects for Tegra114
  ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
  ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
Signed-off-by: Olof Johansson <olof@lixom.net>

The Kconfig options selected by ARCH_TEGRA_*_SOC were recently sorted.
Update the newly added ARCH_TEGRA_114_SOC's select statements to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

CONFIG_ARCH_TEGRA_114_SOC doesn't currently enable gpiolib, which causes
numerous build problems building a Tegra kernel with only Tegra114
enabled, and not Tegra20 or Tegra30. Enable ARCH_REQUIRE_GPIOLIB to
solve this. However, all Tegra will use gpiolib, so select this option
from ARCH_TEGRA rather than each individual ARCH_TEGRA_*_SOC, to
prevent this problem for any future chips.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes the build error when ARCH_TEGRA_114_SOC is enabled
and ARCH_TEGRA_3x_SOC is disabled.

This provides Tegra114 with its own tegra114_init_early() instead of
making use of tegra30_init_early() so that T114 build doesn't depend
on T3x anymore.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-soc4-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Fourth round of Renesas ARM-based SoC changes for v3.9

Register ARM architected timer.

This is preparatory work by Magnus Damm for SoC(s) that use
the ARM architected timer.

* tag 'renesas-soc4-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: Register ARM architected timer

From Shawn Guo:
imx soc changes for 3.9

 - Sort out imx DEBUG_LL uart port selection
 - A couple of imx_v6_v7_defconfig updates

* tag 'imx-soc-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx_v6_v7_defconfig: enable anatop regulator and snvs rtc
  ARM: imx: support DEBUG_LL uart port selection for all i.MX SoCs
  ARM: imx: use separated debug uart symbol for imx31 and imx35
  ARM: imx_v6_v7_defconfig: Select IPUV3 driver

Merge tag 'omap-for-v3.9/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

From Tony Lindgren:
OMAP PM related updates via Paul Walmsley <paul@pwsan.com>:

Remove some dead OMAP clock and device integration code and data.
Also, clean up the way that the OMAP device integration code blocks
WFI/WFE to use a consistent mechanism, controlled by a data flag.

Several OMAP2+ power management fixes, optimizations, and cleanup.
This series is a prerequisite for the functional powerdomain
conversion series.

* tag 'omap-for-v3.9/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: powerdomain: fix whitespace, improve flag comments
  ARM: OMAP2+: clockdomain: convert existing atomic usecounts into spinlock-protected shorts/ints
  ARM: OMAP2+: clockdomain: work on wkdep/sleepdep functions
  ARM: OMAP2xxx: CM: remove autodep handling
  ARM: OMAP2+: powerdomain/clockdomain: add a per-powerdomain spinlock
  ARM: OMAP2+: PM/powerdomain: move omap_set_pwrdm_state() to powerdomain code
  ARM: OMAP2: PM/powerdomain: drop unnecessary pwrdm_wait_transition()
  ARM: OMAP2xxx: PM: clean up some crufty powerstate programming code
  ARM: OMAP2+: clockdomain: add pwrdm_state_switch() call to clkdm_sleep()
  ARM: OMAP2+: powerdomain: fix powerdomain trace integration
  ARM: OMAP4: MPUSS PM: remove unnecessary shim functions for powerdomain control
  ARM: OMAP3xxx: CPUIdle: optimize __omap3_enter_idle()
  ARM: OMAP2420: hwmod data/PM: use hwmod to block WFI when I2C active
  ARM: OMAP2+: hwmod: add support for blocking WFI when a device is active
  ARM: OMAP3xxx: CPUIdle: simplify the PER next-state code
  ARM: OMAP2xxx: powerdomain: core powerdomain missing logic retention states
  ARM: OMAP2xxx: clock data: clean up unused null clocks
  ARM: OMAP4: clock/hwmod data: remove MODULEMODE entries in mux + gate combos
  ARM: OMAP4: clock/hwmod data: start to remove some IP block control "clocks"
  ARM: OMAP2+: omap_device: remove obsolete pm_lats and early_device code

Fix build error in board-dt-tegra114.c(next-20130204)
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reported-by: Sami Liedes<sliedes@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Based on two separate cleanup branches, it's now empty and can be removed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>

Merge tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc

From Stepen Warren:
ARM: tegra: add Tegra114 SoC support

This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.

These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.

This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.

* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
  ARM: DT: tegra114: add pinmux DT entry
  ARM: DT: tegra114: add GPIO DT entry
  ARM: tegra114: select PINCTRL for Tegra114 SoC
  ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
  ARM: tegra: Add SMMU entry to Tegra114 DT
  ARM: tegra: add AHB entry to Tegra114 DT
  ARM: tegra: Add initial support for Tegra114 SoC.
  ARM: dt: tegra114: Add new board, Pluto
  ARM: dt: tegra114: Add new board, Dalmore
  ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
  ARM: tegra: fuse: Add chip ID Tegra114 0x35
  ARM: OMAP: Make use of available scu_a9_get_base() interface
  ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
  ARM: Add API to detect SCU base address from CP15
  ARM: tegra: Use DT /cpu node to detect number of CPU core
  ARM: tegra: Add CPU nodes to Tegra30 device tree
  ARM: tegra: Add CPU nodes to Tegra20 device tree
  ARM: perf: simplify __hw_perf_event_init err handling
  ARM: perf: remove unnecessary checks for idx < 0
  ARM: perf: handle armpmu_register failing
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit.  # # It looks like you may be
committing a merge.  # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.

Merge tag 'tegra-for-3.9-soc-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc

From Stephen Warren:
ARM: tegra: cpuidle enhancements

This pull request implements a new "LP2" cpuidle state for Tegra20,
which makes use of the couple cpuidle feature.

It is based on (most of) the previous pull request, with tag
tegra-for-3.9-soc-usb.

* tag 'tegra-for-3.9-soc-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
  ARM: tegra20: cpuidle: apply coupled cpuidle for powered-down mode
  ARM: tegra20: flowctrl: add support for cpu_suspend_enter/exit
  clk: tegra20: Implementing CPU low-power function for tegra_cpu_car_ops
  ARM: tegra20: cpuidle: add powered-down state for secondary CPU
  ARM: tegra: add pending SGI checking API
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc

From Stephen Warren:
ARM: tegra: USB driver cleanup

The Tegra USB driver has a number of issues:

1) The PHY driver isn't a true platform device, and doesn't implement
   the standard USB PHY API.

2) struct device instance numbers were used to make decisions in the
   driver, rather than being parameterized by DT or platform data.

This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.

This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.

* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
  usb: host: tegra: make use of PHY pointer of HCD
  ARM: tegra: Add reset GPIO information to PHY DT node
  usb: host: tegra: don't touch EMC clock
  usb: add APIs to access host registers from Tegra PHY
  USB: PHY: tegra: Get rid of instance number to differentiate PHY type
  USB: PHY: tegra: get rid of instance number to differentiate legacy controller
  ARM: tegra: add clocks properties to USB PHY nodes
  ARM: tegra: add DT nodes for Tegra USB PHY
  usb: phy: remove unused APIs from Tegra PHY.
  usb: host: tegra: Resetting PORT0 based on information received via DT.
  ARM: tegra: Add new DT property to USB node.
  usb: phy: use kzalloc to allocate struct tegra_usb_phy
  ARM: tegra: remove USB address related macros from iomap.h

Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc

From Stephen Warren:
ARM: tegra: Common Clock Framework rework

Tegra already supports the common clock framework, but had issues:

1) The clock driver was located in arch/arm/mach-tegra/ rather than
   drivers/clk/.

2) A single "Tegra clock" type was implemented, rather than separate
   clock types for PLL, mux, divider, ... type in HW.

3) Clock lookups by device drivers were still driven by device name
   and connection ID, rather than through device tree.

This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.

This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.

* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
  clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
  clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
  ARM: tegra30: remove auxdata
  ARM: tegra20: remove auxdata
  ASoC: tegra: remove auxdata
  staging: nvec: remove use of clk_get_sys
  ARM: tegra: paz00: add clock information to DT
  ARM: tegra: add clock properties to Tegra30 DT
  ARM: tegra: add clock properties to Tegra20 DT
  spi: tegra: do not use clock name to get clock
  ARM: tegra: remove legacy clock code
  ARM: tegra: migrate to new clock code
  clk: tegra: add clock support for Tegra30
  clk: tegra: add clock support for Tegra20
  clk: tegra: add Tegra specific clocks
  ARM: tegra: define Tegra30 CAR binding
  ARM: tegra: define Tegra20 CAR binding
  ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
  ARM: tegra: add function to read chipid
  ARM: tegra: fix compile error when disable CPU_IDLE
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Conflicts:
	arch/arm/mach-tegra/board-dt-tegra20.c
	arch/arm/mach-tegra/board-dt-tegra30.c
	arch/arm/mach-tegra/common.c
	arch/arm/mach-tegra/platsmp.c
	drivers/clocksource/Makefile

Merge tag 'renesas-soc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Third round of Renesas ARM-based SoC changes for v3.9

A fix for r8a7779 clocks.

* tag 'renesas-soc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7779: Correct TMU clock support

Register ARM architected timer by default for all mach-shmobile
systems using late timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

From Jason Cooper:
mvebu drivers for v3.9
 - use rtc-mv in mvebu armv7 SoCs
 - add pci-e hotplug for kirkwood

Depends on:
 - tags/mvebu_fixes_for_v3.8-rc6

* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
  cpuidle: kirkwood: Move out of mach directory
  rtc: Add support of rtc-mv for MVEBU SoCs
  ARM: Kirkwood: Support basic hotplug for PCI-E
  arm: mvebu: i2c come back in defconfig
  arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
  Dove: activate GPIO interrupts in DT

Linux 3.8-rc6

From Shawn Guo:
imx6q cpuidle support for 3.9

 - It's based on imx-cleanup-3.9 to avoid conflicts.

* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx6q: support WAIT mode using cpuidle
  ARM: imx: move imx6q_cpuidle_driver into a separate file
  ARM: imx: mask gpc interrupts initially
  ARM: imx: return zero in case next event gets a large increment
  ARM: imx: Remove mx508 support
  ARM: imx: Remove mach-mx51_3ds board
  ARM: imx: use debug_ll_io_init() for imx6q
  ARM: imx: remove unused imx6q_clock_map_io()
  ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>

Still, two delete/change conflicts caused by imx/cleanup:

	arch/arm/mach-imx/mach-mx50_rdp.c
	arch/arm/mach-imx/mach-mx51_3ds.c

Fix the issue:
tree:   git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git next/soc
head:   6ed05a2a
commit: af70fdc9 [4/8] Merge branch 'marco-timer-cleanup-rebase' of
git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/soc
config: make ARCH=arm prima2_defconfig

All error/warnings:

>> arch/arm/mach-prima2/platsmp.c:20:30: fatal error: asm/hardware/gic.h: No such file or directory
   compilation terminated.
--
>> arch/arm/mach-prima2/common.c:15:30: fatal error: asm/hardware/gic.h: No such file or directory
   compilation terminated.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Xie ChanglongX <changlongx.xie@intel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

During code review it was noticed that the clock value for
TMU01 was incorrect and the value for TMU02 was missing.

For reference: As of 3.8-rc6 there are no in-tree consumes of these clocks.
Reported-by: Denis Oliver Kropp <dok@directfb.org>
Reviewed-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Newer versions of udev (such as 182) requires CONFIG_DEVTMPFS_MOUNT to be
selected, otherwise we get a stuck console:

Starting udev
Starting Bootlog daemon: bootlogd: cannot deduce real console device
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

timer resolution of ~32us is pretty low.
v2 has 32bits resolution, so we have quite some headroom, and
can use the 24MHz clock.
v1 has only 16bits, so we only increase v2.

So we just exchange the timrot clock in imx28.
On imx23 we have timrotv1 and everything stays the same.
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Regenerate the mxs_defconfig to match recent kernel using the following
commands:

make mxs_defconfig
make savedefconfig
cp defconfig arch/arm/configs/mxs_defconfig

Then enable these features:
- MTD block access
- UBI and UBIFS
- JFFS2
- EXT2 and EXT4
- AT24 EEPROM support
- Support for most of the SPI flashes
- Support for ethernet PHYs that are usually used on mxs designs
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Eanble anatop regulator and snvs rtc support which are very useful
for imx6q build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Extend imx6q DEBUG_LL uart port selection support to cover all i.MX
SoCs.  The 'range' of the Kconfig option gets dropped, as users
looking at the option must know the uart number on his board.  The
bottom line is that the build system will report an error if an
invalid port number is picked for given SoC.

The header arch/arm/include/debug/imx-uart.h is created to accommodate
all the uart base addresses.  And the header will also be used for
other low-level debug facility later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It's improper to use combined symbol DEBUG_IMX31_IMX35_UART for
imx31 and imx35, because imx31 has 5 UARTs while imx35 only has 3.
So later when we add UART port selection for DEBUG_IMX31_IMX35_UART,
we will have problem.

Use separated Kconfig options for imx31 and imx35 debug uart selection.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Let IPUV3 driver be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Merge tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Second round of Renesas ARM-based SoC changes for v3.9

* Changes to allow unplugging of CPU0 by Ulrich Hecht.

* Changes to add reg and device_type properties to cpus
  device trees entries by Simon Horman.

* tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: mach-shmobile: sh73a0: allow unplugging of CPU0
  ARM: mach-shmobile: add shmobile_cpu_disable_any()
  ARM: mach-shmobile: emev2:  Add reg and device_type properties to cpus
  ARM: mach-shmobile: sh73a0:  Add reg and device_type properties to cpus
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull more device-mapper fixes from Alasdair G Kergon:
 "A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
  support."

* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm: fix write same requests counting
  dm thin: fix queue limits stacking

PullHID fixes from Jiri Kosina:

 - fix i2c-hid and hidraw interaction, by Benjamin Tissoires

 - a quirk to make a particular device (Formosa IR receiver) work
   properly, by Nicholas Santos

* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: i2c-hid: fix i2c_hid_output_raw_report
  HID: usbhid: quirk for Formosa IR receiver
  HID: remove x bit from sensor doc

Pull NFS client bugfixes from Trond Myklebust:

 - Error reporting in nfs_xdev_mount incorrectly maps all errors to
   ENOMEM

 - Fix an NFSv4 refcounting issue

 - Fix a mount failure when the server reboots during NFSv4 trunking
   discovery

 - NFSv4.1 mounts may need to run the lease recovery thread.

 - Don't silently fail setattr() requests on mountpoints

 - Fix a SUNRPC socket/transport livelock and priority queue issue

 - We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.

* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
  SUNRPC: When changing the queue priority, ensure that we change the owner
  NFS: Don't silently fail setattr() requests on mountpoints
  NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
  NFSv4: Fix NFSv4 trunking discovery
  NFSv4: Fix NFSv4 reference counting for trunked sessions
  NFS: Fix error reporting in nfs_xdev_mount

Pull MIPS updates from Ralf Baechle:
 "A number of fixes all across the MIPS tree.  No area is particularly
  standing out and things have cooled down quite nicely for a release."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Function tracer: Fix broken function tracing
  mips: Move __virt_addr_valid() to a place for MIPS 64
  MIPS: Netlogic: Fix UP compilation on XLR
  MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
  MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
  MIPS: Lantiq: Fix cp0_perfcount_irq mapping
  MIPS: DSP: Fix DSP mask for registers.
  MIPS: Fix build failure by adding definition of pfn_pmd().
  MIPS: Octeon: Fix warning.
  MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
  MIPS: PNX833x: Fix comment.
  MIPS: Add struct p_format to union mips_instruction.
  MIPS: Export <asm/break.h>.
  MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
  MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
  MIPS: vpe.c: Fix null pointer dereference in print arguments.

Move the Kirkwood cpuidle driver out of arch/arm/mach-kirkwood and
into drivers/cpuidle. Convert the driver into a platform driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.

Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.

MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.

The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.

Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning.  So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.

The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.

This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr".  When
disabled, there will be two nops.

This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.

When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.

[ralf@linux-mips.org: Folded in  Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.

Device-mapper WRITE SAME support was introduced by commit
23508a96 ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>