MT76x2/MT76x0 has somewhat unreliable tx status reporting, and for that
reason the driver currently does not report per-skb tx ack status at all.
This breaks things like client idle polling, which relies on the tx ack
status of a transmitted nullfunc frame.

This patch adds code to report skb-attached tx status if requested by
mac80211 or the rate control module. Since tx status is polled from a
simple FIFO register, the code needs to account for the possibility of
tx status events getting lost.

The code keeps a list of skbs for which tx status is required and passes
them to mac80211 once tx status has been filled in and the DMA queue is
done with it.
If a tx status event is not received after one second, the status rates
are cleared, and a succesful ACK is indicated to avoid spurious disassoc
during assoc or client polling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

control->sta is set to NULL early when encryption is turned on for the
station and info->control.hw_key is not set.
This code is missing a check for the 802.11 header protected flag, otherwise
it resets the station for other frames, e.g. client probing frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes a crash that could occur if a frame is sent to a station, but the
station's wcid was not used (e.g. for software encrypted mgmt tx)
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make functions static where possible
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce dfs support in mt76x0e driver and unlock radar channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x2 DFS support in mt76x02-lib module in order to
be reused by mt76x0 driver and unlock DFS frequencies
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Unify drv_bss_info_changed mac80211 callback and remove duplicated
code in mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_set_rts_threshold and mt76x02_mac_set_tx_protection
routines in mt76x02-lib module and remove duplicated code in mt76x0
and mt76x2 drivers. Remove pci_mac.c and mt76x0/mac.c since now are
empty files
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing VHT MT_TX_PROT register init values
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_set_tx_ackto and mt76x02_set_coverage_class routines
in mt76x02-lib module in order to be reused by mt76x0 driver.
This is a preliminary patch to unify drv_bss_info_changed mac80211
callback between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing mac80211 callbacks to mt76x0e_ops data structure
and add mt76x02_beacon utility routines in mt76x0_bss_info_changed
in order to enable/disable beacon transmission
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x02_init_beacon_config utility routine in mt76x02-lib
module in order to be reused by mt76x0 driver configuring
BSSID registers and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_sta_ps utility routine in mt76x02_util.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_tx beacon utility routines in mt76x02_mmio.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_beacon mac routines in mt76x02_mac.c in
order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add missing firmware declaration for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.

This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make previously exported functions static where possible
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mac workqueue support to mt76x2u driver in order
to compute device statistics and add mac stuck routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_debugfs in mt76x02-lib module in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_update_channel routine in mt76x02-lib module in
order to be reused by mt76x0 driver adding get_survey support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Improve initvals_phy.h code readability (there are no actual changes
of original values)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>