The firmware API defined in the header files didn't match
the structure that are actually passed by the firmware.
The impact could be a decision for MIMO in Tx or Rx in
coex scenarios.

Fixes: 430a3bba ("iwlwifi: mvm: BT Coex - new API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.

Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi.  These references were inherited from a previous
project and are irrelevant here.  Additionally, remove some irrelevant
references to 5100 HW.  Remove all these.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Although nmi was triggered fine till now, it appears
that the driver didn't write the exact correct values
to the correct addresses for each HW.
Fix the nmi triggering by setting the correct addresses
and values.

Fixes: 4c9706dc ("iwlwifi: update nmi register")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.

Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.

Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Fix this issue if it is not supported by the firmware.

Fixes: 00f481bd ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code.  Also, export rate
decision logic to a separate function.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Getting the NVM data in a000 devices should be shared
across operation mode.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Add the smem configuration to the fw data dump, once
the firmware crashes. This is useful mainly for later
parsing of the smem.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

One of the defines has a wrong value.

Fixes: 1afb0ae4 ("iwlwifi: allow combining different phy images with mac images")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

There are a few places where we don't have a space between the * and
the @ in the parameter description.  Also, in one case, the @ had
trailing space before the parameter name.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Change iwl_set_ucode_api_flags(), iwl_set_ucode_capabilities() to be void.
No need to check returned values.
Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.

Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.

Fixes: 503ab8c5 ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Set RX_FLAG_DECRYPTED in case of MMIC failure so that
ieee80211_rx_h_decrypt() doesnt drop the frame before getting to
ieee80211_rx_h_michael_mic_verify().
Signed-off-by: Michael Skeffington <mike@astro.ai>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rate_control_ops structure is only passed as an argument to the
function ieee80211_rate_control_{register/unregister}. This argument
is of type const, so declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding arguments
are of type const, so declare the structure to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

After association, ping is not working when sweeping the channel at the
AP side. It is caused by having incorrect carrier state (OFF) for the STA
in successful roaming. This patch sets the carrier state ON for the case.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When the device/firmware supports multi-channel, it can have P2P
connection and regular connection with AP simultaneous. In this case,
the num_different_channels in wiphy info was not correct when firmware
supports multi-channel (The iw wiphy# info showed "#channels <= 1" in
interface combinations). It caused association failed and error message
"CTRL-EVENT-FREQ-CONFLICT error" in wpa_supplicant when P2P GO interface
was running at the same time.
The root cause is that the num_different_channels was always overridden
to 1 in brcmf_setup_ifmodes even multi-channel was enabled.
We correct the logic by moving num_different_channels setting forward.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When setting wpa_auth to WPA_AUTH_NONE(1) in AP mode with WEP security,
firmware will set privacy bit and add WPA OUI in VENDOR IE in beacon and
probe response. The security type in softAP beacons confuse the
supplicant in client side, and the user client will see [WPA-?] in
supplicant scan result. So we set WPA_AUTH_DISABLED in softAP mode with
OPEN security.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Per below statement about p2p device address in WFA P2P
spec $2.4.3:

The P2P Device Address of a P2P Device shall be its globally
administered MAC address, or its globally administered MAC
address with the locally administered bit set.

This patch follow above statement, using a separate device
address for p2p interface
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch wrapper wps ie in pass through tlv, so that
firmware could parse correctly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Commit 4d7ab36f ("mwifiex: Do not change bss_type in
change_virtual_intf") kept original bss_type unchanged. bss_num should
keep the same style, in this way. Unique tuple (bss_type, bss_num) will
be able to locate the right priv structure.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver is doing netif_carrier_off during suspend, which will set
the IFF_LOWER_UP flag to 0. As a result certain applications
will think this as a real carrier down and behave accordingly.
This will cause issues like loss of IP address, for example. To
fix this use netif_device_dettach during suspend.

Fixes: 0026b32d ('mwifiex: fix Tx timeout issue during suspend test')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

BUFFER_AVAILABLE interrupt is sent by firmware to indicate
change in buffer status. We should check buffer status while
handling this interrupt. Currently buffer status is checked
only while dequeueing packets. This patch fixes a data
traffic stuck problem observed occasionally.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We get buffer full event from firmware whenever Tx queue is full
Host should stop writing packets after this and resume after
buffer free event.
Buffer status checking is optimized for once in 4 times if
BUFF_FULL condition is not set, otherwise once for every
packet.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi_sdio_check_buffer_status would be the appropriate name
for this function as we are checking hardware buffers
availability status.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

TX command frame set_antenna is modified to use common
descriptor structure. Also it's subframe type is set.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch implements rfkill_poll handler. Also, necessary changes
are done in interface up and down handler to support rfkill
functionality.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch fixes the uninitialized descriptor pointer
issue in function rsi_send_internal_mgmt_frame().
Descriptor should point to start of the skb data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9a629faf ("rsi: immediate wakeup bit and priority for TX command packets")
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

No need to get into the submenu to disable all BCMA-related config entries.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>