Bring in second round of updates for 3.11.

Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

* Fix version recognition in elantech_set_properties

  The new hardware reports itself as v7 but the packets'
  structure is unaltered.

* Fix packet type recognition in elantech_packet_check_v4

  The bitmask used for v6 is too wide, only the last three bits of
  the third byte in a packet (packet[3] & 0x03) are actually used to
  distinguish between packet types.
  Starting from v7, additional information (to be interpreted) is
  stored in the remaining bits (packets[3] & 0x1c).
  In addition, the value stored in (packet[0] & 0x0c) is no longer
  a constant but contains additional information yet to be deciphered.
  This change should be backwards compatible with v6 hardware.

Additional-author: Giovanni Frigione <gio.frigione@gmail.com>
Signed-off-by: Matteo Delfino <kendatsuba@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In TSG4, register map is 512bytes long and to access all of it,
one bit from address byte is used (which bit to use differs for
I2C and SPI);

Since common code used for TSG3 and TSG4 for I2C, this parameter
wrongly used as u8. TSG3 does not access beyond 255 bytes
but TSG4 may.

Tested-on:TMA3XX DVB && TMA4XX DVB
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If probe() fails after cd->xfer_buf allocated, it will not freed.
Added kfree(cd->xfer_buf) with and error label.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since the driver was converted to polled device infrastructure we need
to make sure it is enabled.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's declare platform data a const pointer so that we don't accitentally
change it. Also fetch it with dev_get_platdata().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The June 2013 Macbook Air (13'') has a new trackpad protocol; four new
values are inserted in the header, and the mode switch is no longer
needed. This patch adds support for the new devices.

Cc: stable@vger.kernel.org
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds keyboard support for MacbookAir6,2 as WELLSPRING8
(0x0291, 0x0292, 0x0293). The touchpad is handled in a separate
bcm5974 patch, as usual.

Cc: stable@vger.kernel.org
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We leak "cd" if the cd->xfer_buf allocation fails.  It was weird to
"goto error_gpio_irq" so I changed the label name.  (Label names should
reflect the label location not the goto location otherwise you get an
"all roads lead to Rome problem").
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If "cd" were NULL then we would dereference it when we print the error
message.  Fortunately enough, it can't ever be NULL so we can remove
those lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

"*max" is a size_t (long) type but "1" is an int so static checkers
complain that the shift could wrap.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare first set of updates for 3.11 merge window.

There is no need to roll our own polling scheme when we already have
one implemented by the core.
Tested-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The vref field was not used by the driver and was removed from the
platform data structure.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Cypress TrueTouch(tm) Standard Product controllers,
Generation4 devices, SPI adapter module.

This driver adds communication support with TTSP controller
using SPI bus.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Cypress TrueTouch(tm) Standard Product controllers,
Generation4 devices, I2C adapter module.

This driver adds communication support with TTSP controller
using I2C bus.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Cypress TrueTouch(tm) Standard Product controllers,
Generetion4 devices, Core driver.

Core driver is interface between host and TTSP controller and processes
data sent by controller.

Responsibilities of module are IRQ handling, reading system information
registers and sending multi-touch protocol type B events.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Existing I2C code is for TrueTouch Gen3 devices

TrueTouch Gen4 device is using same protocol, will split driver into
two pieces to use common code with both drivers.

Read/Write functions parameter list modified, since shared code will
be used by two separate drivers and these drivers are not sharing same
structs, parameters updated to use common structures.
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The OLPC XO-1.75 and XO-4 laptops include a PS/2 touchpad and an AT
keyboard, yet they do not have a hardware PS/2 controller. Instead, a
firmware runs on a dedicated core ("Security Processor", part of the SoC)
that acts as a PS/2 controller through bit-banging.

Communication between the main cpu (Application Processor) and the
Security Processor happens via a standard command mechanism implemented
by the SoC. Add a driver for this interface to enable keyboard/mouse
input on this platform.

Original author: Saadia Baloch
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull in changes from Henrik: "a trivial MT documentation fix".

Although defined in platform data, vref is not used anywhere.

Also remove model, irq, and clear_penirq as they are not used either.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

tsc->polling is write only and the poll local is meaningless
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Added MAP_TRIGGERS_TO_BUTTONS for Mad Catz Street Fighter IV FightPad
device. This controller model was already supported by the xpad
driver, but none of the buttons work correctly without this change.

Tested on kernel version 3.9.5.
Signed-off-by: Shawn Joseph <jms.576@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Although BTN_TOOL_PEN and BTN_TOOL_RUBBER functioned properly, the driver
didn't have hover functionality, so it's been added.

Also, "WACOM_RETRY_CNT" was not used, so it was removed.
Signed-off-by: Tatsunosuke Tobita <tobita.tatsunosuke@wacom.co.jp>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It should not be changed by the driver, so let's make it const pointer.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

pxa27x-keypad includes matrix keys. Make use of matrix_keymap
for the matrix keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This is effectively already in force through input_mt_init_slots, and uinput
too ignores the actual minimum.

Since slots are a kernel-genenerated axis only, non-zero minimums make
little sense and are likely to cause errors. Better to treat a non-zero
minimum as kernel bug if it ever happens.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>

Several drivers don't build on s390 with CONFIG_PCI disabled as
they require MMIO functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If userspace requests current KEY-state, they very likely assume that no
such events are pending in the output queue of the evdev device.
Otherwise, they will parse events which they already handled via
EVIOCGKEY(). For XKB applications this can cause irreversible keyboard
states if a modifier is locked multiple times because a CTRL-DOWN event is
handled once via EVIOCGKEY() and once from the queue via read(), even
though it should handle it only once.

Therefore, lets do the only logical thing and flush the evdev queue
atomically during this ioctl. We only flush events that are affected by
the given ioctl.

This only affects boolean events like KEY, SND, SW and LED. ABS, REL and
others are not affected as duplicate events can be handled gracefully by
user-space.

Note: This actually breaks semantics of the evdev ABI. However,
investigations showed that userspace already expects the new semantics and
we end up fixing at least all XKB applications.
All applications that are aware of this race-condition mirror the KEY
state for each open-file and detect/drop duplicate events. Hence, they do
not care whether duplicates are posted or not and work fine with this fix.

Also note that we need proper locking to guarantee atomicity and avoid
dead-locks. event_lock must be locked before queue_lock (see input-core).
However, we can safely release event_lock while flushing the queue. This
allows the input-core to proceed with pending events and only stop if it
needs our queue_lock to post new events.
This should guarantee that we don't block event-dispatching for too long
while flushing a single event queue.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch fixes warnings due to missing lock on write error path.

  WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
  Hardware name: empty
  Pid: 26563, comm: dd Tainted: P           O 3.9.4 #12
  Call Trace:
    hpfs_truncate+0x75/0x80 [hpfs]
    hpfs_write_begin+0x84/0x90 [hpfs]
    _hpfs_bmap+0x10/0x10 [hpfs]
    generic_file_buffered_write+0x121/0x2c0
    __generic_file_aio_write+0x1c7/0x3f0
    generic_file_aio_write+0x7c/0x100
    do_sync_write+0x98/0xd0
    hpfs_file_write+0xd/0x50 [hpfs]
    vfs_write+0xa2/0x160
    sys_write+0x51/0xa0
    page_fault+0x22/0x30
    system_call_fastpath+0x1a/0x1f
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org  # 2.6.39+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:

 - Trivial: unused variable removal

 - Posix-timers: Add the clock ID to the new proc interface to make it
   useful.  The interface is new and should be functional when we reach
   the final 3.10 release.

 - Cure a false positive warning in the tick code introduced by the
   overhaul in 3.10

 - Fix for a persistent clock detection regression introduced in this
   cycle

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Correct run-time detection of persistent_clock.
  ntp: Remove unused variable flags in __hardpps
  posix-timers: Show clock ID in proc file
  tick: Cure broadcast false positive pending bit warning