Merge tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.5:
 - Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
   so that SPI NOR device can be probed.
 - Fix power button of E60K02 board by removing LDORTC2 regulator.
 - A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
   remove the boot regression caused by 8267ff89 ("ARM: imx: Add
   serial number support for i.MX6/7 SoCs").
 - A couple of fixes on LS1028A SoC TMU regarding to calibration data
   and reboot register configuration.
 - Fix a regression seen on imx6ul-evk board by marking always-on for
   the regulator that is shared by many peripherals.
 - Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.

* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: Fix boot crash if ocotp is not found
  ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
  ARM: dts: imx6ul-evk: Fix peripheral regulator
  arm64: dts: ls1028a: fix reboot node
  arm64: dts: ls1028a: fix typo in TMU calibration data
  ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
  ARM: dts: e60k02: fix power button
  ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing

Link: https://lore.kernel.org/r/20191212122427.GK15858@dragonSigned-off-by: Olof Johansson <olof@lixom.net>

The imx_soc_device_init functions tries to fetch the ocotp regmap in
order to soc serial number. If regmap fetch fails then a message is
printed but regmap_read is called anyway and the system crashes.

Failing to lookup ocotp regmap shouldn't be a fatal boot error so check
that the pointer is valid.

Only side-effect of ocotp lookup failure now is that serial number will
be reported as all-zeros which is acceptable.

Cc: stable@vger.kernel.org
Fixes: 8267ff89 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is currently off and that's not desirable: default imx config is
meant to be generally useful for development and debugging.

Running git bisect between v5.4 and v5.5-rc1 finds this started from
commit 0e4a459f ("tracing: Remove unnecessary DEBUG_FS dependency")

Explicit CONFIG_DEBUG_FS=y was earlier removed by
commit c29d541f ("ARM: imx_v6_v7_defconfig: Remove unneeded options")

A very similar fix was required before:
commit 7e9eb626 ("ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Many peripherals are affected by gpio5/2, not just sensors. One of those
is ethernet phy so network boot is current broken.

Fix by renaming reg_sensors and marking it as "always on". Also add a
comment asking for careful testing if this is to be made dynamic in the
future.

The "peri_3v3" naming is similar to imx6sx-sdb and regulator-name is
same string as in schematics (VPERI_3V3).

Fixes: 09e2b104 ("ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The reboot register isn't located inside the DCFG controller, but in its
own RST controller. Fix it.

Fixes: 8897f325 ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reset controller fixes for v5.5, part 2

Fix the example in the brcmstb-reset device tree bindings, remove a bogus
resource alignment check from the reset-brcmstb driver, fix the documented
return value type for the reset_control_array_get functions, and fix a
devres memory leak when requesting optional, not present reset controls.

* tag 'reset-fixes-for-v5.5-2' of git://git.pengutronix.de/git/pza/linux:
  reset: Do not register resource data for missing resets
  reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
  reset: brcmstb: Remove resource checks
  dt-bindings: reset: Fix brcmstb-reset example

Link: https://lore.kernel.org/r/bb59b9f83892aa3c876f5da87890b0496f2dc755.camel@pengutronix.deSigned-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
v5.5-rc1, please pull the following:

- Nicolas fixes the SoC's dma-range property to cover the full 1GB
  aperture

- Stefan fixes the critical temperature trip point to be set before the
  firmware performs thermal throttling

- Florian fixes the BCM5301X and Cygnus MDIO nodes to have corrected
  #address-cells and #size-cells properties

* tag 'arm-soc/for-5.5/devicetree-fixes' of https://github.com/Broadcom/stblinux:
  ARM: dts: bcm283x: Fix critical trip point
  ARM: dts: Cygnus: Fix MDIO node address/size cells
  ARM: dts: bcm2711: fix soc's node dma-ranges
  ARM: dts: BCM5301X: Fix MDIO node address/size cells

Link: https://lore.kernel.org/r/20191210205850.12442-1-f.fainelli@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

The file was moved, causing a build error:

In file included from /git/arm-soc/arch/arm/mach-mmp/pxa168.c:28:
arch/arm/mach-mmp/pxa168.h:22:10: fatal error: cputype.h: No such file or directory

Include it from the new location.

Link: https://lore.kernel.org/r/20191210203409.2875880-1-arnd@arndb.de
Fixes: 32adcaa0 ("ARM: mmp: move cputype.h to include/linux/soc/")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

The temperature sensor may jump backwards because there is a wrong
calibration value. Both values have to be monotonically increasing.
Fix it.

This was tested on a custom board.

Fixes: 571cebfe ("arm64: dts: ls1028a: Add Thermal Monitor Unit node")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

After the commit 8267ff89 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
the kernel doesn't start on i.MX6ULL/ULZ SoC.
Tested on next-20191205.

For i.MX6ULL/ULZ the variable "ocotp_compat" is set to "fsl,imx6ul-ocotp", but with commit
ffbc34bf ("nvmem: imx-ocotp: Implement i.MX6ULL/ULZ support") and commit
f243bc82 ("ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible") the value
"fsl,imx6ull-ocotp" is already defined and set in device tree...

By setting "ocotp_compat" to "fsl,imx6ull-ocotp" the kernel does boot.

Fixes: 8267ff89 ("ARM: imx: Add serial number support for i.MX6/7 SoCs")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher

So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).

Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.

Fixes: 0fe4d218 ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

When an optional reset is not present, __devm_reset_control_get() and
devm_reset_control_array_get() still register resource data to release
the non-existing reset on cleanup, which is futile.

Fix this by skipping NULL reset control pointers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

of_reset_control_array_get() and devm_reset_control_array_get() return
struct reset_control pointers, not internal struct reset_control_array
pointers, just like all other reset control API calls.

Correct the kerneldoc to match the code.

Fixes: 17c82e20 ("reset: Add APIs to manage array of resets")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The use of IS_ALIGNED() is incorrect, the typical resource we pass looks
like this: start: 0x8404318, size: 0x30. When using IS_ALIGNED() we will
get the following 0x8404318 & (0x18 - 1) = 0x10 which is definitively
not equal to 0, same goes with the size. These two checks would make the
driver fail probing.

Remove the resource checks, since there should be no constraint on the
base addresse or size.

Fixes: 77750bc0 ("reset: Add Broadcom STB SW_INIT reset controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The reset controller has a #reset-cells value of 1, so we should see a
phandle plus a register identifier, fix the example.

Fixes: 0807caf6 ("dt-bindings: reset: Add document for Broadcom STB reset controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The MDIO node on Cygnus had an reversed #address-cells and
 #size-cells properties, correct those.

Fixes: 40c26d3a ("ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY")
Reported-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Raspberry Pi's firmware has a feature to select how much memory to
reserve for its GPU called 'gpu_mem'. The possible values go from 16MB
to 944MB, with a default of 64MB. This memory resides in the topmost
part of the lower 1GB memory area and grows bigger expanding towards the
begging of memory.

It turns out that with low 'gpu_mem' values (16MB and 32MB) the size of
the memory available to the system in the lower 1GB area can outgrow the
interconnect's dma-range as its size was selected based on the maximum
system memory available given the default gpu_mem configuration. This
makes that memory slice unavailable for DMA. And may cause nasty kernel
warnings if CMA happens to include it.

Change soc's dma-ranges to really reflect it's HW limitation, which is
being able to only DMA to the lower 1GB area.

Fixes: 7dbe8c62 ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The MDIO node on BCM5301X had an reversed #address-cells and
 #size-cells properties, correct those, silencing checker warnings:

.../linux/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml: mdio@18003000: #address-cells:0:0: 1 was expected
Reported-by: Simon Horman <simon.horman@netronome.com>
Fixes: 23f1eca6 ("ARM: dts: BCM5301X: Specify MDIO bus in the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Merge tag 'vexpress-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes

ARMv7 Vexpress fixes for v5.5

Switching the cpumask from topology core to OPP sharing, as the topology
core cpumask can be modified during cpu hotplug to avoid setting up
wrong cpufreq policy cpumask.

* tag 'vexpress-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  cpufreq: vexpress-spc: Switch cpumask from topology core to OPP sharing
  ARM: vexpress: Set-up shared OPP table instead of individual for each CPU

Link: https://lore.kernel.org/r/20191209140037.GC25155@bogusSigned-off-by: Olof Johansson <olof@lixom.net>

Since commit ca74b316 ("arm: Use common cpu_topology structure and
functions.") the core cpumask has to be modified during cpu hotplug
operations. So using them to set up cpufreq policy cpumask may be
incorrect as it may contain only cpus that are online at that instance.

Instead, we can use the cpumask setup by OPP library that contains all
the cpus sharing OPP table using dev_pm_opp_get_sharing_cpus.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Currently we add individual copy of same OPP table for each CPU within
the cluster. This is redundant and doesn't reflect the reality.

We can't use core cpumask to set policy->cpus in ve_spc_cpufreq_init()
anymore as it gets called via cpuhp_cpufreq_online()->cpufreq_online()
->cpufreq_driver->init() and the cpumask gets updated upon CPU hotplug
operations. It also may cause issues when the vexpress_spc_cpufreq
driver is built as a module.

Since ve_spc_clk_init is built-in device initcall, we should be able to
use the same topology_core_cpumask to set the opp sharing cpumask via
dev_pm_opp_set_sharing_cpus and use the same later in the driver via
dev_pm_opp_get_sharing_cpus.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

The power button was only producing irqs, but no key events,
Forced power down with long key press works, so probably
only a short spike arrives at the SoC.
Further investigation shows that LDORTC2 is off after boot
of the vendor kernel. LDORTC2 is shared with a GPIO at the pmic
which probably transfers the button press to the SoC.
That regulator off at boot, so "regulator-boot-on" is definitively
wrong. So remove that.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: c100ea86 ("ARM: dts: add Netronix E60K02 board common file")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Without this "jedec,spi-nor" compatible property, probing of the SPI NOR
does not work on the NXP i.MX6ULL EVK. Fix this by adding this
compatible property to the DT.

Fixes: 7d77b850 ("ARM: dts: imx6ull: fix the imx6ull-14x14-evk configuration")
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID

Pull more input updates from Dmitry Torokhov:

 - fixups for Synaptics RMI4 driver

 - a quirk for Goodinx touchscreen on Teclast tablet

 - a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

 - updates to snvs_pwrkey driver

 - polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Pull iomap fixes from Darrick Wong:
 "Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Pull xfs fixes from Darrick Wong:
 "Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak

Pull orangefs update from Mike Marshall:
 "orangefs: posix open permission checking...

  Orangefs has no open, and orangefs checks file permissions on each
  file access. Posix requires that file permissions be checked on open
  and nowhere else. Orangefs-through-the-kernel needs to seem posix
  compliant.

  The VFS opens files, even if the filesystem provides no method. We can
  see if a file was successfully opened for read and or for write by
  looking at file->f_mode.

  When writes are flowing from the page cache, file is no longer
  available. We can trust the VFS to have checked file->f_mode before
  writing to the page cache.

  The mode of a file might change between when it is opened and IO
  commences, or it might be created with an arbitrary mode.

  We'll make sure we don't hit EACCES during the IO stage by using
  UID 0"

[ This is "posixish", but not a great solution in the long run, since a
  proper secure network server shouldn't really trust the client like this.
  But proper and secure POSIX behavior requires an open method and a
  resulting cookie for IO of some kind, or similar.    - Linus ]

* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: posix open permission checking...

Pull nfsd updates from Bruce Fields:
 "This is a relatively quiet cycle for nfsd, mainly various bugfixes.

  Possibly most interesting is Trond's fixes for some callback races
  that were due to my incomplete understanding of rpc client shutdown.
  Unfortunately at the last minute I've started noticing a new
  intermittent failure to send callbacks. As the logic seems basically
  correct, I'm leaving Trond's patches in for now, and hope to find a
  fix in the next week so I don't have to revert those patches"

* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: depend on CRYPTO_MD5 for legacy client tracking
  NFSD fixing possible null pointer derefering in copy offload
  nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
  nfsd: Ensure CLONE persists data and metadata changes to the target file
  SUNRPC: Fix backchannel latency metrics
  nfsd: restore NFSv3 ACL support
  nfsd: v4 support requires CRYPTO_SHA256
  nfsd: Fix cld_net->cn_tfm initialization
  lockd: remove __KERNEL__ ifdefs
  sunrpc: remove __KERNEL__ ifdefs
  race in exportfs_decode_fh()
  nfsd: Drop LIST_HEAD where the variable it declares is never used.
  nfsd: document callback_wq serialization of callback code
  nfsd: mark cb path down on unknown errors
  nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
  nfsd: minor 4.1 callback cleanup
  SUNRPC: Fix svcauth_gss_proxy_init()
  SUNRPC: Trace gssproxy upcall results
  sunrpc: fix crash when cache_head become valid before update
  nfsd: remove private bin2hex implementation
  ...

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

  Features:

   - NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
     copy of a file from one source server to a different target
     server).

   - New RDMA tracepoints for debugging congestion control and Local
     Invalidate WRs.

  Bugfixes and cleanups

   - Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
     layoutreturn

   - Handle bad/dead sessions correctly in nfs41_sequence_process()

   - Various bugfixes to the delegation return operation.

   - Various bugfixes pertaining to delegations that have been revoked.

   - Cleanups to the NFS timespec code to avoid unnecessary conversions
     between timespec and timespec64.

   - Fix unstable RDMA connections after a reconnect

   - Close race between waking an RDMA sender and posting a receive

   - Wake pending RDMA tasks if connection fails

   - Fix MR list corruption, and clean up MR usage

   - Fix another RPCSEC_GSS issue with MIC buffer space"

* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
  SUNRPC: Capture completion of all RPC tasks
  SUNRPC: Fix another issue with MIC buffer space
  NFS4: Trace lock reclaims
  NFS4: Trace state recovery operation
  NFSv4.2 fix memory leak in nfs42_ssc_open
  NFSv4.2 fix kfree in __nfs42_copy_file_range
  NFS: remove duplicated include from nfs4file.c
  NFSv4: Make _nfs42_proc_copy_notify() static
  NFS: Fallocate should use the nfs4_fattr_bitmap
  NFS: Return -ETXTBSY when attempting to write to a swapfile
  fs: nfs: sysfs: Remove NULL check before kfree
  NFS: remove unneeded semicolon
  NFSv4: add declaration of current_stateid
  NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
  NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
  nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
  SUNRPC: Avoid RPC delays when exiting suspend
  NFS: Add a tracepoint in nfs_fh_to_dentry()
  NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
  NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
  ...

We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.

Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

Pull VFIO updates from Alex Williamson:

 - Remove hugepage checks for reserved pfns (Ben Luo)

 - Fix irq-bypass unregister ordering (Jiang Yi)

* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
  vfio/pci: call irq_bypass_unregister_producer() before freeing irq
  vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()

Pull more xen updates from Juergen Gross:

 - a patch to fix a build warning

 - a cleanup of no longer needed code in the Xen event handling

 - a small series for the Xen grant driver avoiding high order
   allocations and replacing an insane global limit by a per-call one

 - a small series fixing Xen frontend/backend module referencing

* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkback: allow module to be cleanly unloaded
  xen/xenbus: reference count registered modules
  xen/gntdev: switch from kcalloc() to kvcalloc()
  xen/gntdev: replace global limit of mapped pages by limit per call
  xen/gntdev: remove redundant non-zero check on ret
  xen/events: remove event handling recursion detection

Merge misc Kconfig updates from Andrew Morton:
 "A number of changes to Kconfig files under lib/ from Changbin Du and
  Krzysztof Kozlowski"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/: fix Kconfig indentation
  kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
  kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
  kernel-hacking: create a submenu for scheduler debugging options
  kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
  kernel-hacking: move Oops into 'Lockups and Hangs'
  kernel-hacking: move kernel testing and coverage options to same submenu
  kernel-hacking: group kernel data structures debugging together
  kernel-hacking: create submenu for arch special debugging options
  kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>