This reverts commit dc9a1929.

3610 cards don't support UAPSD.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add one more 7265 series HW ID.
Edit one existing 7265 series HW ID.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The non-split wiphy state shouldn't be increased in size
so move the new set_qos_map command into the split if
statement.

Cc: stable@vger.kernel.org (3.14+)
Fixes: fa9ffc74 ("cfg80211: Add support for QoS mapping")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The current sched scan channel configuration code
configures all the supported channels for scanning.

However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.

Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.

While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

MAX_JIFFY_OFFSET has no meaning when calculating the
elapsed jiffies, as jiffies run out until ULONG_MAX.

This miscalculation results in erroneous values
in case of a wrap-around.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This reverts commit 8eca1fb6.

Felix notes that this broke regulatory, leaving channel 12 open for AP
operation in the US regulatory domain where it isn't permitted.

Link: http://mid.gmane.org/53A6C0FF.9090104@openwrt.orgReported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After skb allocation and call to ieee80211_wep_encrypt in ieee80211_send_auth
the flow fails with a warning in ieee80211_wep_add_iv on verification of
available head/tailroom needed for WEP_IV and WEP_ICV.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When pairing fails hci_conn refcnt drops below zero. This cause that
ACL link is not disconnected when disconnect timeout fires.

Probably this is because l2cap_conn_del calls l2cap_chan_del for each
channel, and inside l2cap_chan_del conn is dropped. After that loop
hci_chan_del is called which also drops conn.

Anyway, as it is desrcibed in hci_core.h, it is known that refcnt
drops below 0 sometimes and it should be fine. If so, let disconnect
link when hci_conn_timeout fires and refcnt is 0 or below. This patch
does it.

This affects PTS test SM_TC_JW_BV_05_C

Logs from scenario:

[69713.706227] [6515] pair_device:
[69713.706230] [6515] hci_conn_add: hci0 dst 00:1b:dc:06:06:22
[69713.706233] [6515] hci_dev_hold: hci0 orig refcnt 8
[69713.706235] [6515] hci_conn_init_sysfs: conn ffff88021f65a000
[69713.706239] [6515] hci_req_add_ev: hci0 opcode 0x200d plen 25
[69713.706242] [6515] hci_prepare_cmd: skb len 28
[69713.706243] [6515] hci_req_run: length 1
[69713.706248] [6515] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 0
[69713.706251] [6515] hci_dev_put: hci0 orig refcnt 9
[69713.706281] [8909] hci_cmd_work: hci0 cmd_cnt 1 cmd queued 1
[69713.706288] [8909] hci_send_frame: hci0 type 1 len 28
[69713.706290] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 28
[69713.706316] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.706382] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.711664] [8909] hci_rx_work: hci0
[69713.711668] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 6
[69713.711680] [8909] hci_rx_work: hci0 Event packet
[69713.711683] [8909] hci_cs_le_create_conn: hci0 status 0x00
[69713.711685] [8909] hci_sent_cmd_data: hci0 opcode 0x200d
[69713.711688] [8909] hci_req_cmd_complete: opcode 0x200d status 0x00
[69713.711690] [8909] hci_sent_cmd_data: hci0 opcode 0x200d
[69713.711695] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.711744] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.818875] [8909] hci_rx_work: hci0
[69713.818889] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 21
[69713.818913] [8909] hci_rx_work: hci0 Event packet
[69713.818917] [8909] hci_le_conn_complete_evt: hci0 status 0x00
[69713.818922] [8909] hci_send_to_control: len 19
[69713.818927] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.818938] [8909] hci_conn_add_sysfs: conn ffff88021f65a000
[69713.818975] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
[69713.818981] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
...
[69713.819021] [8909] hci_dev_hold: hci0 orig refcnt 10
[69713.819025] [8909] l2cap_connect_cfm: hcon ffff88021f65a000 bdaddr 00:1b:dc:06:06:22 status 0
[69713.819028] [8909] hci_chan_create: hci0 hcon ffff88021f65a000
[69713.819031] [8909] l2cap_conn_add: hcon ffff88021f65a000 conn ffff880221005c00 hchan ffff88020d60b1c0
[69713.819034] [8909] l2cap_conn_ready: conn ffff880221005c00
[69713.819036] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.819037] [8909] smp_conn_security: conn ffff880221005c00 hcon ffff88021f65a000 level 0x02
[69713.819039] [8909] smp_chan_create:
[69713.819041] [8909] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 1
[69713.819043] [8909] smp_send_cmd: code 0x01
[69713.819045] [8909] hci_send_acl: hci0 chan ffff88020d60b1c0 flags 0x0000
[69713.819046] [5949] hci_sock_recvmsg: sock ffff8800941a9900, sk ffff88012bf4e800
[69713.819049] [8909] hci_queue_acl: hci0 nonfrag skb ffff88005157c100 len 15
[69713.819055] [5949] hci_sock_recvmsg: sock ffff8800941a9900, sk ffff88012bf4e800
[69713.819057] [8909] l2cap_le_conn_ready:
[69713.819064] [8909] l2cap_chan_create: chan ffff88005ede2c00
[69713.819066] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 1
[69713.819069] [8909] l2cap_sock_init: sk ffff88005ede5800
[69713.819072] [8909] bt_accept_enqueue: parent ffff880160356000, sk ffff88005ede5800
[69713.819074] [8909] __l2cap_chan_add: conn ffff880221005c00, psm 0x00, dcid 0x0004
[69713.819076] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 2
[69713.819078] [8909] hci_conn_hold: hcon ffff88021f65a000 orig refcnt 2
[69713.819080] [8909] smp_conn_security: conn ffff880221005c00 hcon ffff88021f65a000 level 0x01
[69713.819082] [8909] l2cap_sock_ready_cb: sk ffff88005ede5800, parent ffff880160356000
[69713.819086] [8909] le_pairing_complete_cb: status 0
[69713.819091] [8909] hci_tx_work: hci0 acl 10 sco 8 le 0
[69713.819093] [8909] hci_sched_acl: hci0
[69713.819094] [8909] hci_sched_sco: hci0
[69713.819096] [8909] hci_sched_esco: hci0
[69713.819098] [8909] hci_sched_le: hci0
[69713.819099] [8909] hci_chan_sent: hci0
[69713.819101] [8909] hci_chan_sent: chan ffff88020d60b1c0 quote 10
[69713.819104] [8909] hci_sched_le: chan ffff88020d60b1c0 skb ffff88005157c100 len 15 priority 7
[69713.819106] [8909] hci_send_frame: hci0 type 2 len 15
[69713.819108] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 15
[69713.819119] [8909] hci_chan_sent: hci0
[69713.819121] [8909] hci_prio_recalculate: hci0
[69713.819123] [8909] process_pending_rx:
[69713.819226] [6450] hci_sock_recvmsg: sock ffff88005e758780, sk ffff88010323d400
...
[69713.822022] [6450] l2cap_sock_accept: sk ffff880160356000 timeo 0
[69713.822024] [6450] bt_accept_dequeue: parent ffff880160356000
[69713.822026] [6450] bt_accept_unlink: sk ffff88005ede5800 state 1
[69713.822028] [6450] l2cap_sock_accept: new socket ffff88005ede5800
[69713.822368] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.822375] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.822383] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.822414] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
...
[69713.823255] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.823259] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.824322] [6450] l2cap_sock_getname: sock ffff8800941ab700, sk ffff88005ede5800
[69713.824330] [6450] l2cap_sock_getsockopt: sk ffff88005ede5800
[69713.825029] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69713.825187] [6450] l2cap_sock_sendmsg: sock ffff8800941ab700, sk ffff88005ede5800
[69713.825189] [6450] bt_sock_wait_ready: sk ffff88005ede5800
[69713.825192] [6450] l2cap_create_basic_pdu: chan ffff88005ede2c00 len 3
[69713.825196] [6450] l2cap_do_send: chan ffff88005ede2c00, skb ffff880160b0b500 len 7 priority 0
[69713.825199] [6450] hci_send_acl: hci0 chan ffff88020d60b1c0 flags 0x0000
[69713.825201] [6450] hci_queue_acl: hci0 nonfrag skb ffff880160b0b500 len 11
[69713.825210] [8909] hci_tx_work: hci0 acl 9 sco 8 le 0
[69713.825213] [8909] hci_sched_acl: hci0
[69713.825214] [8909] hci_sched_sco: hci0
[69713.825216] [8909] hci_sched_esco: hci0
[69713.825217] [8909] hci_sched_le: hci0
[69713.825219] [8909] hci_chan_sent: hci0
[69713.825221] [8909] hci_chan_sent: chan ffff88020d60b1c0 quote 9
[69713.825223] [8909] hci_sched_le: chan ffff88020d60b1c0 skb ffff880160b0b500 len 11 priority 0
[69713.825225] [8909] hci_send_frame: hci0 type 2 len 11
[69713.825227] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 11
[69713.825242] [8909] hci_chan_sent: hci0
[69713.825253] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.825253] [8909] hci_prio_recalculate: hci0
[69713.825292] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.825768] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69713.866902] [8909] hci_rx_work: hci0
[69713.866921] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 7
[69713.866928] [8909] hci_rx_work: hci0 Event packet
[69713.866931] [8909] hci_num_comp_pkts_evt: hci0 num_hndl 1
[69713.866937] [8909] hci_tx_work: hci0 acl 9 sco 8 le 0
[69713.866939] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.866940] [8909] hci_sched_acl: hci0
...
[69713.866944] [8909] hci_sched_le: hci0
[69713.866953] [8909] hci_chan_sent: hci0
[69713.866997] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.867840] [28074] hci_rx_work: hci0
[69713.867844] [28074] hci_send_to_monitor: hdev ffff88021f0c7000 len 7
[69713.867850] [28074] hci_rx_work: hci0 Event packet
[69713.867853] [28074] hci_num_comp_pkts_evt: hci0 num_hndl 1
[69713.867857] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69713.867858] [28074] hci_tx_work: hci0 acl 10 sco 8 le 0
[69713.867860] [28074] hci_sched_acl: hci0
[69713.867861] [28074] hci_sched_sco: hci0
[69713.867862] [28074] hci_sched_esco: hci0
[69713.867863] [28074] hci_sched_le: hci0
[69713.867865] [28074] hci_chan_sent: hci0
[69713.867888] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145661] [8909] hci_rx_work: hci0
[69714.145666] [8909] hci_send_to_monitor: hdev ffff88021f0c7000 len 10
[69714.145676] [8909] hci_rx_work: hci0 ACL data packet
[69714.145679] [8909] hci_acldata_packet: hci0 len 6 handle 0x002d flags 0x0002
[69714.145681] [8909] hci_conn_enter_active_mode: hcon ffff88021f65a000 mode 0
[69714.145683] [8909] l2cap_recv_acldata: conn ffff880221005c00 len 6 flags 0x2
[69714.145693] [8909] l2cap_recv_frame: len 2, cid 0x0006
[69714.145696] [8909] hci_send_to_control: len 14
[69714.145710] [8909] smp_chan_destroy:
[69714.145713] [8909] pairing_complete: status 3
[69714.145714] [8909] cmd_complete: sock ffff88010323ac00
[69714.145717] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 3
[69714.145719] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145720] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
[69714.145722] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
[69714.145724] [6450] bt_sock_poll: sock ffff8801db6b4f00, sk ffff880160351c00
...
[69714.145735] [6515] hci_sock_recvmsg: sock ffff88005e75a080, sk ffff88010323ac00
[69714.145737] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 2
[69714.145739] [8909] l2cap_conn_del: hcon ffff88021f65a000 conn ffff880221005c00, err 13
[69714.145740] [6450] bt_sock_poll: sock ffff8801db6b5400, sk ffff88021e775000
[69714.145743] [6450] bt_sock_poll: sock ffff8801db6b5e00, sk ffff880160356000
[69714.145744] [8909] l2cap_chan_hold: chan ffff88005ede2c00 orig refcnt 3
[69714.145746] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
[69714.145748] [8909] l2cap_chan_del: chan ffff88005ede2c00, conn ffff880221005c00, err 13
[69714.145749] [8909] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 4
[69714.145751] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 1
[69714.145754] [6450] bt_sock_poll: sock ffff8800941ab700, sk ffff88005ede5800
[69714.145756] [8909] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 3
[69714.145759] [8909] hci_chan_del: hci0 hcon ffff88021f65a000 chan ffff88020d60b1c0
[69714.145766] [5949] hci_sock_recvmsg: sock ffff8800941a9680, sk ffff88012bf4d000
[69714.145787] [6515] hci_sock_release: sock ffff88005e75a080 sk ffff88010323ac00
[69714.146002] [6450] hci_sock_recvmsg: sock ffff88005e758780, sk ffff88010323d400
[69714.150795] [6450] l2cap_sock_release: sock ffff8800941ab700, sk ffff88005ede5800
[69714.150799] [6450] l2cap_sock_shutdown: sock ffff8800941ab700, sk ffff88005ede5800
[69714.150802] [6450] l2cap_chan_close: chan ffff88005ede2c00 state BT_CLOSED
[69714.150805] [6450] l2cap_sock_kill: sk ffff88005ede5800 state BT_CLOSED
[69714.150806] [6450] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 2
[69714.150808] [6450] l2cap_sock_destruct: sk ffff88005ede5800
[69714.150809] [6450] l2cap_chan_put: chan ffff88005ede2c00 orig refcnt 1
[69714.150811] [6450] l2cap_chan_destroy: chan ffff88005ede2c00
[69714.150970] [6450] bt_sock_poll: sock ffff88005e758500, sk ffff88010323b800
...
[69714.151991] [8909] hci_conn_drop: hcon ffff88021f65a000 orig refcnt 0
[69716.150339] [8909] hci_conn_timeout: hcon ffff88021f65a000 state BT_CONNECTED, refcnt -1
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If we need an MITM protected connection but the local and remote IO
capabilities cannot provide it we should reject the pairing attempt in
the appropriate way. This patch adds the missing checks for such a
situation to the smp_cmd_pairing_req() and smp_cmd_pairing_rsp()
functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We'll need to do authentication method lookups from more than one place,
so refactor the lookup into its own function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When we receive a pairing request or an internal request to start
pairing we shouldn't blindly overwrite the existing pending_sec_level
value as that may actually be higher than the new one. This patch fixes
the SMP code to only overwrite the value in case the new one is higher
than the old.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This reverts commit ca58e594.

For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.

The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cc is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Alexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x

As reported by Niels, starting rfkill polling during device probe
(commit e2bc7c5f, generally sane change) broke rfkill on rt2500pci
device. I considered that bug as some initalization issue, which
should be fixed on rt2500pci specific code. But after several
attempts (see bug report for details) we fail to find working solution.
Hence I decided to revert to old behaviour on rt2500pci to fix
regression.

Additionally patch also unregister rfkill on device remove instead
of ifconfig down, what was another issue introduced by bad commit.

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=73821

Fixes: e2bc7c5f ("rt2x00: Fix rfkill_polling register function.")
Cc: stable@vger.kernel.org
Bisected-by: Niels <nille0386@googlemail.com>
Reported-and-tested-by: Niels <nille0386@googlemail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Support for firmware rev 508+ was added years ago, but we never noticed
it reports channel in a different way for G-PHY devices. Instead of
offset from 2400 MHz it simply passes channel id (AKA hw_value).

So far it was (most probably) affecting monitor mode users only, but
the following recent commit made it noticeable for quite everybody:

commit 3afc2167
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Tue Mar 4 16:50:13 2014 +0200

    cfg80211/mac80211: ignore signal if the frame was heard on wrong channel
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) boots into a state that does
not actually require loading a firmware file. The vendors driver finds out
about this by checking a firmware state register, so this patch adds this here.

Finally, with this patch applied, my wifi dongle actually becomes
useful (scan + connect to wpa network works).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The device 057c:8501 (AVM Fritz! WLAN v2 rev. B) currently does not
load. One thing observed is that the vendors driver detects EFUSE mode
for this device, but rt2800usb does not. This is due to rt2800usb
lacking a check for the firmware mode present in the vendors driver,
that this patch adopts for rt2800usb.

With this patch applied, the 'RF chipset' detection does no longer fail.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On USB we can not get atomically TKIP key. We have to disable support
for TKIP acceleration on USB hardware to avoid bug as showed bellow.

[  860.827243] BUG: scheduling while atomic: hostapd/3397/0x00000002
<snip>
[  860.827280] Call Trace:
[  860.827282]  [<ffffffff81682ea6>] dump_stack+0x4d/0x66
[  860.827284]  [<ffffffff8167eb9b>] __schedule_bug+0x47/0x55
[  860.827285]  [<ffffffff81685bb3>] __schedule+0x733/0x7b0
[  860.827287]  [<ffffffff81685c59>] schedule+0x29/0x70
[  860.827289]  [<ffffffff81684f8a>] schedule_timeout+0x15a/0x2b0
[  860.827291]  [<ffffffff8105ac50>] ? ftrace_raw_event_tick_stop+0xc0/0xc0
[  860.827294]  [<ffffffff810c13c2>] ? __module_text_address+0x12/0x70
[  860.827296]  [<ffffffff81686823>] wait_for_completion_timeout+0xb3/0x140
[  860.827298]  [<ffffffff81080fc0>] ? wake_up_state+0x20/0x20
[  860.827301]  [<ffffffff814d5b3d>] usb_start_wait_urb+0x7d/0x150
[  860.827303]  [<ffffffff814d5cd5>] usb_control_msg+0xc5/0x110
[  860.827305]  [<ffffffffa02fb0c6>] rt2x00usb_vendor_request+0xc6/0x160  [rt2x00usb]
[  860.827307]  [<ffffffffa02fb215>] rt2x00usb_vendor_req_buff_lock+0x75/0x150 [rt2x00usb]
[  860.827309]  [<ffffffffa02fb393>] rt2x00usb_vendor_request_buff+0xa3/0xe0 [rt2x00usb]
[  860.827311]  [<ffffffffa023d1a3>] rt2x00usb_register_multiread+0x33/0x40 [rt2800usb]
[  860.827314]  [<ffffffffa05805f9>] rt2800_get_tkip_seq+0x39/0x50  [rt2800lib]
[  860.827321]  [<ffffffffa0480f88>] ieee80211_get_key+0x218/0x2a0  [mac80211]
[  860.827322]  [<ffffffff815cc68c>] ? __nlmsg_put+0x6c/0x80
[  860.827329]  [<ffffffffa051b02e>] nl80211_get_key+0x22e/0x360 [cfg80211]

Cc: stable@vger.kernel.org
Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com>
Reported-and-tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On PCIe Tx data path, network interface specific tx_info
parameters such as bss_num and bss_type are saved at
"skb->cb + sizeof(dma_addr_t)" (returned by MWIFIEX_SKB_TXCB).
Later mwifiex_map_pci_memory() called from
mwifiex_pcie_send_data() will memcpy
sizeof(struct mwifiex_dma_mapping) bytes to save PCIe DMA
address and length information at beginning of skb->cb.
This accidently overwrites bss_num and bss_type saved in skb->cb
previously because bss_num/bss_type and mwifiex_dma_mapping data
overlap.
Similarly, on PCIe Rx data path, rx_info parameters overlaps
with PCIe DMA address and length information too.

Fix it by defining mwifiex_cb structure and having
MWIFIEX_SKB_TXCB and MWIFIEX_SKB_RXCB return the correct address
of tx_info/rx_info using the structure members.

Also add a BUILD_BUG_ON to maks sure that mwifiex_cb structure
doesn't exceed the size of skb->cb.
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes regression introduced by adding some G-PHY devices to the
list of dual band devices. There is simply no support for 5 GHz on
G-PHY devices in b43. It results in:
WARNING: CPU: 0 PID: 79 at drivers/net/wireless/b43/phy_g.c:75 b43_gphy_channel_switch+0x125/0x130 [b43]()
b43-phy1 ERROR: PHY init: Channel switch to default failed

Regression was introduced by the following commit:

commit 773cfc50
Author: Rafał Miłecki <zajec5@gmail.com>
Date:   Mon May 19 23:18:55 2014 +0200

    b43: add more devices to the bands database
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more SCSI updates from James Bottomley:
 "This is just a couple of drivers (hpsa and lpfc) that got left out for
  further testing in linux-next.  We also have one fix to a prior
  submission (qla2xxx sparse)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
  qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
  lpfc: Update lpfc version to driver version 10.2.8001.0
  lpfc: Fix ExpressLane priority setup
  lpfc: mark old devices as obsolete
  lpfc: Fix for initializing RRQ bitmap
  lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
  lpfc: Update lpfc version to driver version 10.2.8000.0
  lpfc: Update Copyright on changed files from 8.3.45 patches
  lpfc: Update Copyright on changed files
  lpfc: Fixed locking for scsi task management commands
  lpfc: Convert runtime references to old xlane cfg param to fof cfg param
  lpfc: Fix FW dump using sysfs
  lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
  lpfc: Fixed kernel panic in lpfc_abort_handler
  lpfc: Fix locking for postbufq when freeing
  lpfc: Fix locking for lpfc_hba_down_post
  lpfc: Fix dynamic transitions of FirstBurst from on to off
  hpsa: fix handling of hpsa_volume_offline return value
  hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
  hpsa: remove messages about volume status VPD inquiry page not supported
  ...

Pull more btrfs updates from Chris Mason:
 "This has a few fixes since our last pull and a new ioctl for doing
  btree searches from userland.  It's very similar to the existing
  ioctl, but lets us return larger items back down to the app"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  btrfs: tree_search, search_ioctl: direct copy to userspace
  btrfs: new function read_extent_buffer_to_user
  btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
  btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
  btrfs: tree_search, search_ioctl: accept varying buffer
  btrfs: tree_search: eliminate redundant nr_items check

Pull aio fix and cleanups from Ben LaHaise:
 "This consists of a couple of code cleanups plus a minor bug fix"

* git://git.kvack.org/~bcrl/aio-next:
  aio: cleanup: flatten kill_ioctx()
  aio: report error from io_destroy() when threads race in io_destroy()
  fs/aio.c: Remove ctx parameter in kiocb_cancel

Tetsuo Handa wrote:
 "Commit 62a8067a ("bio_vec-backed iov_iter") introduced an unnamed
  union inside a struct which gcc-4.4.7 cannot handle.  Name the unnamed
   union as u in order to fix build failure"

Let's do this instead: there is only one place in the entire tree that
steps into this breakage.  Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h

What doesn't work is handling their initializers:

struct {
	int a;
	union {
		int b;
		char c;
	};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};

is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.

Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e.  x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace.  Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of .  and -> instead of doing the right thing.

The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>