This adds support for sbs-charger compilant chips as defined here:
http://sbs-forum.org/specs/sbc110.pdf

This was tested on a arm board connected to an LTC4100 battery charger
chip.
Signed-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Adds device tree documentation for SBS charger compilant devices as defined
here: http://sbs-forum.org/specs/sbc110.pdfSigned-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

So what if there is a status_gpio specified? bq24735_charger_is_present()
do have a working fallback for the case of no status_gpio.

Simplify this by not special casing setups w/o status_gpio, folding
two consecutive if-blocks in the process.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

During probe, it makes no sense to take care to first not issue any
i2c commands to verify if the connected part really is a bq24735, to
later simply fail the probe in the next step when trying to configure
the charger. So, delay configuration of the charging parameters until
the charger is accessible (i.e. when the AC adapter is present) as
part of enabling the charging.

This also fixes the rather serious issue that the charging parameters
are lost when the AC adapter is disconnected.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

bq24735_enable_charging() needs to call bq24735_config_charging(),
which is something to change later, this is just a preparatory patch.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

"tps65217-charger" is more appropriate name because the driver supports
not only AC but also USB charger.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Rename it as tps65217_charger_get_property().
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Replace 'ac_props' with 'charger_props'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Replace 'ac' of tps65217_charger structure with 'psy'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This driver supports AC and USB chargers. Generic name is preferred.
Replace 'ac_online' with 'online'.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

TPS65217 has two charger interrupts - AC and USB power status change.

Interrupt number in the TPS65217 driver data:
  IRQ number is only used on requesting the interrupt, so no need to keep
  it inside the driver data.

Interrupt handler:
  Check not only AC but also USB charger status.
  In both cases, enable charging operation.

Interrupt request:
  If an interrupt number is invalid, then use legacy polling thread.
  Otherwise, create IRQ threads to handle AC and USB charger event.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use the task_struct variable for running polling thread. If polling task
is activated, then use it to stop running thread.
This is a preceding step of supporting two interrupts of TPS65217 charger,
so checking single IRQ number is not appropriate when the module is removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch replaces the deprecated extcon API as following:
- extcon_set_cable_state_() -> extcon_set_state_sync()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Use managed resource function devm_power_supply_register instead of
power_supply_register to simplify the error path by allowing unregistering
to happen automatically on error and remove.
Removing max8997_battery_remove function also as it is now redundant.

Also removing out of memory printk message after kzalloc as there is
already enough information on failure.
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The X-Powers AXP223 shares most of its behaviour with the AXP221 PMIC
but allows the VBUS power supply max current to be set to 100mA (like
the AXP209 PMIC).

This basically adds a new compatible to the VBUS power supply driver and
adds a check on the compatible when setting current max limit.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This adds the "x-powers,axp223-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

AXP20X and AXP22X PMICs allow setting the min voltage and max current of
VBUS power supply. This adds entries in sysfs to allow to do so.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This replaces calls to of_device_is_compatible to check data field of
of_device_id matched when probing the driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

If the ac-detect gpio does not support interrupts, provide a fallback
to poll the gpio at a configurable interval.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

In order for the MSB -> LSB latching to work correctly we must read the
2 8 bit registers of a 12 bit value in one consecutive read.

This fixes voltage_ocv reporting inconsistent values on my tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

In order for the MSB -> LSB latching to work correctly we must read the
2 8 bit registers of a 15 bit value in one consecutive read.

This fixes charge_full reporting 3498768 on some reads and 3354624 one
other reads on my tablet (for the 3354624 value the raw LSB is 0x00).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

If reading the register fails, return the actual error code, instead
of the uninitialized val variable;
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The ACOK pin on the bq24735 is active-high, of course meaning that when
AC is OK the pin is high. However, all Tegra dts files have incorrectly
specified active-high even though the signal is inverted on the Tegra
boards. This has worked since the Linux driver has also inverted the
meaning of the GPIO. Fix this situation by simply specifying in the
bindings what everybody else agrees on; that the ti,ac-detect-gpios is
active on AC adapter absence.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Providing value bits outside of the mask is pointless.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

When the axp288_faul_gauge driver was originally merged, it was
merged with a dependency on some other driver providing platform
data for it.

However the battery-data-framework which should provide that data
never got merged, resulting in x86 tablets / laptops with an axp288
having no working battery monitor, as before this commit the driver
would simply return -ENODEV if there is no platform data.

This commit removes the dependency on the platform_data instead
checking that the firmware has initialized the fuel-gauge and
reading the info back from the pmic.

What is missing from the read-back info is the table to map raw adc
values to temperature, so this commit drops the temperature and
temperature limits properties. The min voltage, charge design and
model name info is also missing. Note that none of these are really
important for userspace to have.

All other functionality is preserved and actually made available
by this commit.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=88471Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

When the axp288_charger driver was originally merged, it was merged with
a dependency on some other driver providing platform data for it.

However the battery-data-framework which should provide that data never
got merged, so the axp288_charger as merged upstream has never worked,
its probe method simply always returns -ENODEV.

This commit removes the dependency on the platform_data instead reading
back the charging current and charging voltage that the firmware has set
and using those values as the maximum values the user may set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Make charger_init_hw_regs propagate i2c errors, instead of only warning
about them and then ignoring them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a338 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t

Pull SMP hotplug notifier removal from Thomas Gleixner:
 "This is the final cleanup of the hotplug notifier infrastructure. The
  series has been reintgrated in the last two days because there came a
  new driver using the old infrastructure via the SCSI tree.

  Summary:

   - convert the last leftover drivers utilizing notifiers

   - fixup for a completely broken hotplug user

   - prevent setup of already used states

   - removal of the notifiers

   - treewide cleanup of hotplug state names

   - consolidation of state space

  There is a sphinx based documentation pending, but that needs review
  from the documentation folks"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-xp: Consolidate hotplug state space
  irqchip/gic: Consolidate hotplug state space
  coresight/etm3/4x: Consolidate hotplug state space
  cpu/hotplug: Cleanup state names
  cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
  staging/lustre/libcfs: Convert to hotplug state machine
  scsi/bnx2i: Convert to hotplug state machine
  scsi/bnx2fc: Convert to hotplug state machine
  cpu/hotplug: Prevent overwriting of callbacks
  x86/msr: Remove bogus cleanup from the error path
  bus: arm-ccn: Prevent hotplug callback leak
  perf/x86/intel/cstate: Prevent hotplug callback leak
  ARM/imx/mmcd: Fix broken cpu hotplug handling
  scsi: qedi: Convert to hotplug state machine

Pull turbostat updates from Len Brown.

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: remove obsolete -M, -m, -C, -c options
  tools/power turbostat: Make extensible via the --add parameter
  tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
  tools/power turbostat: line up headers when -M is used
  tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
  tools/power turbostat: Support Knights Mill (KNM)
  tools/power turbostat: Display HWP OOB status
  tools/power turbostat: fix Denverton BCLK
  tools/power turbostat: use intel-family.h model strings
  tools/power/turbostat: Add Denverton RAPL support
  tools/power/turbostat: Add Denverton support
  tools/power/turbostat: split core MSR support into status + limit
  tools/power turbostat: fix error case overflow read of slm_freq_table[]
  tools/power turbostat: Allocate correct amount of fd and irq entries
  tools/power turbostat: switch to tab delimited output
  tools/power turbostat: Gracefully handle ACPI S3
  tools/power turbostat: tidy up output on Joule counter overflow

Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.

This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.

The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).

This improves the performance of page lock intensive microbenchmarks by
2-3%.

Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.

Get rid of the union and just keep ktime_t as simple typedef of type s64.

The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>