It has been tested with a 802.11 frame generator and by checking the FCS field
of each received frame with the value reported by the Atheros hardware. This
patch is useful if you are trying to analyze non standard 802.11 frame going
over the air.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

At present, the results of an SSB core scan are only logged when
CONFIG_SSB_DEBUG is "y". As this may not be set in a distro kernel,
it is difficult interpret many problems posted in bug reports or in
help forums.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200 is able to detect when it's been hard-killed, but doesn't update
the core rfkill state or update userspace. Ensure that the state is updated,
allowing the rfkill core to notify userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libipw unconditionally calls wiphy_unregister, but it's up to the driver
to register it in the first place. ipw2100 fails to do so. Add the necessary
glue code, and also ensure that rfkill statuses get set up appropriately.

(Augmented for proper wiphy_unregister placement. -- JWL)
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Initiate the conversion of libipw to the new cfg80211 configuration API.

For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone.  Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.

(v2: Fix unconditional wiphy_unregister in libipw which was causing
     problems for ipw2100, somewhat based on prior attempted fix
     by Zhu Yi <yi.zhu@intel.com>.  Previously both original version of
     this patch and Zhu Yi's fix attempt were reverted due to
     discovery of regressions. -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is sometimes useful to debug HT issues
as it shows what exactly the stack thinks
the peer supports.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With WEXT, it happens frequently that the SME
requests an authentication but then deauthenticates
right away because some new parameters came along.
Every time this happens we print a deauth message
and send a deauth frame, but both of that is rather
confusing. Avoid it by aborting the authentication
process silently, and telling cfg80211 about that.

The patch looks larger than it really is:
__cfg80211_auth_remove() is split out from
cfg80211_send_auth_timeout(), there's no new code
except __cfg80211_auth_canceled() (a one-liner) and
the mac80211 bits (7 new lines of code).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.

The rate control algorithms also need TX status, but
they don't require it.

Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.

This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
 * transmitter, which must be equal to the sender (origin)
 * receiver (on the wireless medium), which is the AP in
   the case of managed mode
 * the recipient (destination), which is on the APs local
   network segment

In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.

To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.

Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enforce all device constraints on the descriptor memory region.

There are several constraints on the descriptor memory, as documented
in the specification. The current code does not enforce them and/or
incorrectly enforces them.

Those constraints are:
- The address limitations on 30/32bit engines, that also apply to
  the skbs.
- The 4k alignment requirement on 30/32bit engines.
- The 8k alignment requirement on 64bit engines.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It's enough code to have its own file, I think.
Especially since I'm going to add to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Janakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Janakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_esbq_exec’:
drivers/net/wireless/wl3501_cs.c:387: warning: ‘tmp’ is used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:384: note: ‘tmp’ was declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When going from/to a WEP protected IBSS, we need to
leave this one and join a new one to take care of
the changed capability.

Cc: Hong Zhang <henryzhang62@yahoo.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Not assigning the vif pointer causes an oops.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 rejects all association requests when in associated state. This
prevents clean roaming within an ESS since one would first need to
disassociate before being able to request reassociation.

Accept the reassociation request and let the old association to be
dropped when the new one is completed. This fixes nl80211-based
roaming with the current snapshot version of wpa_supplicant (that has
code for requesting reassociation explicitly withthe previous BSSID
attribute).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.

It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.

kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: David-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes warnings:

drivers/net/wireless/wl12xx/wl1251_rx.c: In function 'wl1251_rx_status':
drivers/net/wireless/wl12xx/wl1251_rx.c:75:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
  warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to IEEE80211 standard all the data packets have to be sent with
TODS bit set. This patch fixes the null data packet format which was sent
without TODS bit set. This should fix many problems associated with
power save. Janne Ylalehto also found this fix in the same time as mine,
for a different bug he was working on.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In some cases, the IRQ loop handler could acknowledge an interrupt to
the chipset, but not service it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Filter out unwanted events to reduce wakeups.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for IRQ looping. Helps in the case that we have e.g. multiple
packets coming from the network when we wake up from the ELP.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch increases the number of beacons to be missed before generating
SYNC TIMEOUT event. It increases the beacon timeout period to 500
microseconds, which gives enough time for the firmware to receive probe
response or beacon. Also handled the regain event from firmware once it
receives a probe response or beacon.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch sets the dtim period obtained from the mac80211 to firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The dtim period obtained from the mac80211 is not set to the firmware.
This patch implements the acx command to set correct tbtt and dtim value
to the firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In ps-poll template aid bits 14 and 15 were not masked as required by the
standard. Mask them so that aid is sent in correct format.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Earlier firmware was stored to a memory area allocated with kmalloc()
but finding a a contiguous area of memory long enough for the firmware is
very difficult in certain cases. better to allocate the memory for firmware
with vmalloc() instead and use a small buffer for DMA transfers.

Thanks to Eero Tamminen for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement (slightly) delayed entry into ELP. This will cure several
problems:
  - It works around a firmware race condition if ELP is entered too fast
    after commands (resulting in ELP timeout -traces)
  - It will reduce the number of sleep-wake cycles between already
    scheduled events such as interrupts and tx, hence improving
    performance (less delay in switching between RX and TX)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable beacon filtering when PSM is enabled
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable beacon filtering with the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

At least two revisions of the D-Link DWA 160 exist, called A1 and A2. A1
(USB-ID 07d1:3c10) is already listed in usb.c as D-Link DWA 160A. A2
(USB-ID 07d1:3a09) works if added to ar9170_usb_ids. I didn't do much
testing until now, but I was able to connect to APs using WPA or WEP and
transmit data.

Summary:

* Add model revision number to the comment for D-Link DWA 160 A1 (07d1:3c10)
* Add support for D-Link DWA 160 A2 (07d1:3a09)
Signed-off-by: Thomas Klute <thomas2.klute@uni-dortmund.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>