Resources are not freed in the reverse order of the allocation.
Labels are also mixed-up.

Fix it and reorder code and labels in the error handling path of
'mlxsw_core_bus_device_register()'

Fixes: ef3116e5 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Debabrata Banerjee says:

====================
bonding: bug fixes and regressions

Fixes to bonding driver for balance-alb mode, suitable for stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a regression at some point from the intended functionality of
commit f60c3704 ("bonding: Fix alb mode to only use first level
vlans.")

Given the return value vlan_get_encap_level() we need to store the nest
level of the bond device, and then compare the vlan's encap level to
this. Without this, this check always fails and learning packets are
never sent.

In addition, this same commit caused a regression in the behavior of
balance_alb, which requires learning packets be sent for all interfaces
using the slave's mac in order to load balance properly. For vlan's
that have not set a user mac, we can send after checking one bit.
Otherwise we need send the set mac, albeit defeating rx load balancing
for that vlan.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure multicast, broadcast, and zero mac's cannot be the output of rlb
updates, which should all be directed arps. Receive load balancing will be
collapsed if any of these happen, as the switch will broadcast.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.17-20180510' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
this is a pull request for net/master consisting of 2 patches.

Both patches are from Lukas Wunner and fix two problems found in the
hi311x CAN driver under high load situations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in DP_VERBOSE message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Commit 1f45f78f ("sctp: allow GSO frags to access the chunk too"),
it held the chunk in sctp_ulpevent_make_rcvmsg to access it safely later
in recvmsg. However, it also added sctp_chunk_put in fail_mark err path,
which is only triggered before holding the chunk.

syzbot reported a use-after-free crash happened on this err path, where
it shouldn't call sctp_chunk_put.

This patch simply removes this call.

Fixes: 1f45f78f ("sctp: allow GSO frags to access the chunk too")
Reported-by: syzbot+141d898c5f24489db4aa@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an error occurs, 'mlx4_en_destroy_netdev()' is called.
It then calls 'mlx4_en_free_resources()' which does the needed resources
cleanup.

So, doing some explicit kfree in the error handling path would lead to
some double kfree.

Simplify code to avoid such a case.

Fixes: 67f8b1dc ("net/mlx4_en: Refactor the XDP forwarding rings scheme")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hyper-v transparent bonding should have used master_dev_link.
The netvsc device should look like a master bond device not
like the upper side of a tunnel.

This makes the semantics the same so that userspace applications
looking at network devices see the correct master relationshipship.

Fixes: 0c195567 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
We only have a few fixes this time:
 * WMM element validation
 * SAE timeout
 * add-BA timeout
 * docbook parsing
 * a few memory leaks in error paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sysbot/KMSAN reported an uninit-value in recvmsg() that
I tracked down to tipc_sk_set_orig_addr(), missing
srcaddr->member.scope initialization.

This patches moves srcaddr->sock.scope init to follow
fields order and ease future verifications.

BUG: KMSAN: uninit-value in copy_to_user include/linux/uaccess.h:184 [inline]
BUG: KMSAN: uninit-value in move_addr_to_user+0x32e/0x530 net/socket.c:226
CPU: 0 PID: 4549 Comm: syz-executor287 Not tainted 4.17.0-rc3+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x185/0x1d0 lib/dump_stack.c:113
 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
 kmsan_internal_check_memory+0x135/0x1e0 mm/kmsan/kmsan.c:1157
 kmsan_copy_to_user+0x69/0x160 mm/kmsan/kmsan.c:1199
 copy_to_user include/linux/uaccess.h:184 [inline]
 move_addr_to_user+0x32e/0x530 net/socket.c:226
 ___sys_recvmsg+0x4e2/0x810 net/socket.c:2285
 __sys_recvmsg net/socket.c:2328 [inline]
 __do_sys_recvmsg net/socket.c:2338 [inline]
 __se_sys_recvmsg net/socket.c:2335 [inline]
 __x64_sys_recvmsg+0x325/0x460 net/socket.c:2335
 do_syscall_64+0x154/0x220 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x4455e9
RSP: 002b:00007fe3bd36ddb8 EFLAGS: 00000246 ORIG_RAX: 000000000000002f
RAX: ffffffffffffffda RBX: 00000000006dac24 RCX: 00000000004455e9
RDX: 0000000000002002 RSI: 0000000020000400 RDI: 0000000000000003
RBP: 00000000006dac20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff98ce4b6f R14: 00007fe3bd36e9c0 R15: 0000000000000003

Local variable description: ----addr@___sys_recvmsg
Variable was created at:
 ___sys_recvmsg+0xd5/0x810 net/socket.c:2246
 __sys_recvmsg net/socket.c:2328 [inline]
 __do_sys_recvmsg net/socket.c:2338 [inline]
 __se_sys_recvmsg net/socket.c:2335 [inline]
 __x64_sys_recvmsg+0x325/0x460 net/socket.c:2335

Byte 19 of 32 is uninitialized

Fixes: 31c82a2d ("tipc: add second source address to recvmsg()/recvfrom()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- correct a typo in the value of 'matchPattern' of test 282d, potentially
 causing false negative
- allow errors when 'teardown' executes '$TC action flush action bpf' in
 test 282d, to fix false positive when it is run with act_bpf unloaded
- correct the value of 'matchPattern' in test e939, causing false positive
 in case the BPF JIT is enabled

Fixes: 440ea4ae ("tc-testing: add selftests for 'bpf' action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx4 modify cq limits the coalescing time parameter and
coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
Change type of sample-interval and adaptive_rx_coal parameters in mlx4
driver to u32 as the ethtool holds them as u32 and these parameters are
not limited due to mlx4 HW.

Fixes: c27a02cd ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

copy mbox size to adapter instances of PF0-3 to avoid
mbox log overflow. This fixes the possible protection
fault.

Fixes: baf50868 ("cxgb4: restructure VF mgmt code")
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

firmware expects HMA memory to be zeroed, use __GFP_ZERO
for HMA memory allocation.

Fixes: 8b4e6b3c ("cxgb4: Add HMA support")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Damir reported a breakage of SO_BINDTODEVICE for UDP sockets.
In absence of VRF devices, after commit fb74c277 ("net:
ipv4: add second dif to udp socket lookups") the dif mismatch
isn't fatal anymore for UDP socket lookup with non null
sk_bound_dev_if, breaking SO_BINDTODEVICE semantics.

This changeset addresses the issue making the dif match mandatory
again in the above scenario.
Reported-by: Damir Mansurov <dnman@oktetlabs.ru>
Fixes: fb74c277 ("net: ipv4: add second dif to udp socket lookups")
Fixes: 1801b570 ("net: ipv6: add second dif to udp socket lookups")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After route cache is flushed via ipv4_sysctl_rtcache_flush(), we forget
to reset fnhe_mtu_locked in rt_bind_exception(). When pmtu is updated
in __ip_rt_update_pmtu(), it will return directly since the pmtu is
still locked. e.g.

+ ip netns exec client ping 10.10.1.1 -c 1 -s 1400 -M do
PING 10.10.1.1 (10.10.1.1) 1400(1428) bytes of data.
>From 10.10.0.254 icmp_seq=1 Frag needed and DF set (mtu = 0)
Signed-off-by: David S. Miller <davem@davemloft.net>

On older windows hosts the net_device instance is returned to
the caller of rndis_filter_device_add() without having the presence
bit set first. This would cause any subsequent calls to network device
operations (e.g. MTU change, channel change) to fail after the device
is detached once, returning -ENODEV.

Instead of returning the device instabce, we take the exit path where
we call netif_device_attach()

Fixes: 7b2ee50c ("hv_netvsc: common detach logic")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 29a5dcae ("nfp: flower: offload phys port MTU change") we
take encapsulation headroom into account when calculating the max allowed
MTU.  This is unnecessary as the max MTU advertised by firmware should have
already accounted for encap headroom.

Subtracting headroom twice brings the max MTU below what's necessary for
some deployments.

Fixes: 29a5dcae ("nfp: flower: offload phys port MTU change")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in dev_warn message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in error string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in res_strings string array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed*: Rdma fixes

This patch series include two fixes for bugs related to rdma.
The first has to do with loading the driver over an iWARP
device.
The second fixes a previous commit that added proper link
indication for iWARP / RoCE.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>

A previous commit 4609adc2 ("qede: Fix qedr link update")
added a flow that could allocate rdma event objects from an
interrupt path (link notification). Therefore the kzalloc call
should be done with GFP_ATOMIC.

fixes: 4609adc2 ("qede: Fix qedr link update")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If qede driver was loaded on a device configured for iWARP
the l2 mutex wouldn't be allocated, and some l2 related
resources wouldn't be freed.

fixes: c851a9dc ("qed: Introduce iWARP personality")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending packets as fast as possible using "cangen -g 0 -i -x", the
HI-3110 occasionally latches the interrupt pin high on completion of a
packet, but doesn't set the TXCPLT bit in the INTF register.  The INTF
register contains 0x00 as if no interrupt has occurred.  Even waiting
for a few milliseconds after the interrupt doesn't help.

Work around this apparent erratum by instead checking the TXMTY bit in
the STATF register ("TX FIFO empty").  We know that we've queued up a
packet for transmission if priv->tx_len is nonzero.  If the TX FIFO is
empty, transmission of that packet must have completed.

Note that this is congruent with our handling of received packets, which
likewise gleans from the STATF register whether a packet is waiting in
the RX FIFO, instead of looking at the INTF register.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

hi3110_get_berr_counter() may run concurrently to the rest of the driver
but neglects to acquire the lock protecting access to the SPI device.
As a result, it and the rest of the driver may clobber each other's tx
and rx buffers.

We became aware of this issue because transmission of packets with
"cangen -g 0 -i -x" frequently hung.  It turns out that agetty executes
->do_get_berr_counter every few seconds via the following call stack:

    CPU: 2 PID: 1605 Comm: agetty
    [<7f3f7500>] (hi3110_get_berr_counter [hi311x])
    [<7f130204>] (can_fill_info [can_dev])
    [<80693bc0>] (rtnl_fill_ifinfo)
    [<806949ec>] (rtnl_dump_ifinfo)
    [<806b4834>] (netlink_dump)
    [<806b4bc8>] (netlink_recvmsg)
    [<8065f180>] (sock_recvmsg)
    [<80660f90>] (___sys_recvmsg)
    [<80661e7c>] (__sys_recvmsg)
    [<80661ec0>] (SyS_recvmsg)
    [<80108b20>] (ret_fast_syscall+0x0/0x1c)

agetty listens to netlink messages in order to update the login prompt
when IP addresses change (if /etc/issue contains \4 or \6 escape codes):
https://git.kernel.org/pub/scm/utils/util-linux/util-linux.git/commit/?id=e36deb6424e8

It's a useful feature, though it seems questionable that it causes CAN
bit error statistics to be queried.

Be that as it may, if hi3110_get_berr_counter() is invoked while a frame
is sent by hi3110_hw_tx(), bogus SPI transfers like the following may
occur:

    => 12 00             (hi3110_get_berr_counter() wanted to transmit
                          EC 00 to query the transmit error counter,
                          but the first byte was overwritten by
                          hi3110_hw_tx_frame())

    => EA 00 3E 80 01 FB (hi3110_hw_tx_frame() wanted to transmit a
                          frame, but the first byte was overwritten by
                          hi3110_get_berr_counter() because it wanted
                          to query the receive error counter)

This sequence hangs the transmission because the driver believes it has
sent a frame and waits for the interrupt signaling completion, but in
reality the chip has never sent away the frame since the commands it
received were malformed.

Fix by acquiring the SPI lock in hi3110_get_berr_counter().

I've scrutinized the entire driver for further unlocked SPI accesses but
found no others.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: Stef Walter <stefw@redhat.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When we get link properties through netlink interface with
tipc_nl_node_get_link(), we don't validate TIPC_NLA_LINK_NAME
attribute at all, instead we directly use it. As a consequence,
KMSAN detected the TIPC_NLA_LINK_NAME attribute was an uninitialized
value, and then posted the following complaint:

==================================================================
BUG: KMSAN: uninit-value in strcmp+0xf7/0x160 lib/string.c:329
CPU: 1 PID: 4527 Comm: syz-executor655 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:17 [inline]
  dump_stack+0x185/0x1d0 lib/dump_stack.c:53
  kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
  __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
  strcmp+0xf7/0x160 lib/string.c:329
  tipc_nl_node_get_link+0x220/0x6f0 net/tipc/node.c:1881
  genl_family_rcv_msg net/netlink/genetlink.c:599 [inline]
  genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624
  netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447
  genl_rcv+0x63/0x80 net/netlink/genetlink.c:635
  netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline]
  netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337
  netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
  __sys_sendmsg net/socket.c:2080 [inline]
  SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
  SyS_sendmsg+0x54/0x80 net/socket.c:2087
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x445589
RSP: 002b:00007fb7ee66cdb8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000006dac24 RCX: 0000000000445589
RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003
RBP: 00000000006dac20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffa2bf3f3f R14: 00007fb7ee66d9c0 R15: 0000000000000001

Uninit was created at:
  kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
  kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
  kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
  kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
  slab_post_alloc_hook mm/slab.h:445 [inline]
  slab_alloc_node mm/slub.c:2737 [inline]
  __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
  __kmalloc_reserve net/core/skbuff.c:138 [inline]
  __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
  alloc_skb include/linux/skbuff.h:984 [inline]
  netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline]
  netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
  __sys_sendmsg net/socket.c:2080 [inline]
  SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
  SyS_sendmsg+0x54/0x80 net/socket.c:2087
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
==================================================================

To quiet the complaint, TIPC_NLA_LINK_NAME attribute has been
validated in tipc_nl_node_get_link() before it's used.

Reported-by: syzbot+df0257c92ffd4fcc58cd@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are follow comment errors:
1 The function name is wrong in p9_release_pages() comment.
2 The function name and variable name is wrong in p9_poll_workfn() comment.
3 There is no variable dm_mr and lkey in struct p9_trans_rdma.
4 The function name is wrong in rdma_create_trans() comment.
5 There is no variable initialized in struct virtio_chan.
6 The variable name is wrong in p9_virtio_zc_request() comment.
Signed-off-by: Sun Lianwen <sunlw.fnst@cn.fujitsu.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit a92a0849 "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549

The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.

This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru>
Tested-by: Slava Kardakov <ojab@ojab.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.17-20180508' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2018-05-08

this is a pull request for 7 patches for net/master.

The first patch is by Jakob Unterwurzacher and increases the severity of
bus-off messages in the generic CAN device infrastructure. The next two patches
are by Uwe Kleine-König and fix the endianess detection in the flexcan driver.
Jimmy Assarsson's patch for the kvaser driver corrects the stats counter for
dropped tx-messages. Geert Uytterhoeven provides one patch and Sergei Shtylyov
two patches for the rcan_canfd device tree binding description.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'ieee802154-for-davem-2018-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 2018-05-08

An update from ieee802154 for your *net* tree.

Two fixes for the mcr20a driver, which was being added in the 4.17 merge window,
by Gustavo and myself.
The atusb driver got a change to GFP_KERNEL where no GFP_ATOMIC is needed by
Jia-Ju.

The last and most important fix is from Alex to get IPv6 reassembly working
again for the ieee802154 6lowpan adaptation. This got broken in 4.16 so please
queue this one also up for the 4.16 stable tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the R-Car V3H (R8A77980) SoC support in the R-Car CAN-FD bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Document the R-Car V3M (R8A77970) SoC support in the R-Car CAN-FD bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

R8A7796 is R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Increase rx_dropped, if alloc_can_skb() fails, not tx_dropped.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Commit d50f4630 ("arm: dts: Remove p1010-flexcan compatible from imx
series dts") removed the fallback compatible "fsl,p1010-flexcan" from
the imx device trees. As the flexcan cores on i.MX25, i.MX35 and i.MX53
are identical, introduce the first as fallback for the two latter ones.

Fixes: d50f4630 ("arm: dts: Remove p1010-flexcan compatible from imx series dts")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In commit 88462d2a ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:

	if the dt property "big-endian" is given or
	   the device is compatible to "fsl,p1010-flexcan":
		use big-endian mode;
	else
		use little-endian mode;

This relies on commit d50f4630 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.

Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match

Fixes: 88462d2a ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

bus-off is usually caused by hardware malfunction or configuration error
(baud rate mismatch) and causes a complete loss of communication.

Increase the "bus-off" message's severity from netdev_dbg() to
netdev_info() to make it visible to the user.

A can interface going into bus-off is similar in severity to ethernet's
"Link is Down" message, which is also printed at info level.

It is debatable whether the the "restarted" message should also be
changed to netdev_info() to make the interface state changes
comprehensible from the kernel log. I have chosen to keep the
"restarted" message at dbg for now as the "bus-off" message should be
enough for the user to notice and investigate the problem.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: linux-can@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

syzbot loves to set very small mtu on devices, since it brings joy.
We must make llc_ui_sendmsg() fool proof.

usercopy: Kernel memory overwrite attempt detected to wrapped address (offset 0, size 18446612139802320068)!

kernel BUG at mm/usercopy.c:100!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 17464 Comm: syz-executor1 Not tainted 4.17.0-rc3+ #36
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:usercopy_abort+0xbb/0xbd mm/usercopy.c:88
RSP: 0018:ffff8801868bf800 EFLAGS: 00010282
RAX: 000000000000006c RBX: ffffffff87d2fb00 RCX: 0000000000000000
RDX: 000000000000006c RSI: ffffffff81610731 RDI: ffffed0030d17ef6
RBP: ffff8801868bf858 R08: ffff88018daa4200 R09: ffffed003b5c4fb0
R10: ffffed003b5c4fb0 R11: ffff8801dae27d87 R12: ffffffff87d2f8e0
R13: ffffffff87d2f7a0 R14: ffffffff87d2f7a0 R15: ffffffff87d2f7a0
FS:  00007f56a14ac700(0000) GS:ffff8801dae00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2bc21000 CR3: 00000001abeb1000 CR4: 00000000001426f0
DR0: 0000000020000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000030602
Call Trace:
 check_bogus_address mm/usercopy.c:153 [inline]
 __check_object_size+0x5d9/0x5d9 mm/usercopy.c:256
 check_object_size include/linux/thread_info.h:108 [inline]
 check_copy_size include/linux/thread_info.h:139 [inline]
 copy_from_iter_full include/linux/uio.h:121 [inline]
 memcpy_from_msg include/linux/skbuff.h:3305 [inline]
 llc_ui_sendmsg+0x4b1/0x1530 net/llc/af_llc.c:941
 sock_sendmsg_nosec net/socket.c:629 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:639
 __sys_sendto+0x3d7/0x670 net/socket.c:1789
 __do_sys_sendto net/socket.c:1801 [inline]
 __se_sys_sendto net/socket.c:1797 [inline]
 __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1797
 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x455979
RSP: 002b:00007f56a14abc68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007f56a14ac6d4 RCX: 0000000000455979
RDX: 0000000000000000 RSI: 0000000020000000 RDI: 0000000000000018
RBP: 000000000072bea0 R08: 00000000200012c0 R09: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000548 R14: 00000000006fbf60 R15: 0000000000000000
Code: 55 c0 e8 c0 55 bb ff ff 75 c8 48 8b 55 c0 4d 89 f9 ff 75 d0 4d 89 e8 48 89 d9 4c 89 e6 41 56 48 c7 c7 80 fa d2 87 e8 a0 0b a3 ff <0f> 0b e8 95 55 bb ff e8 c0 a8 f7 ff 8b 95 14 ff ff ff 4d 89 e8
RIP: usercopy_abort+0xbb/0xbd mm/usercopy.c:88 RSP: ffff8801868bf800

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>