Add a warning that the abort mechanism was triggered for device.
Also avoid going through the procedure if abort was already done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
dsa: mv88e6xxx: Fixes for port refactoring

The patches which refactored setting up the switch MACs introduced a
couple of regressions. The RGMII delays for a port can be set using
other mechanism than just phy-mode. Don't overwrite the delays unless
explicitly asked to. This broke my Armada 370 RD. Also, the mv88e6351
family supports setting RGMII delays, but is missing the necessary
entries in the ops structures to allow this.

These fixes are to patches currently in net-next. No need for stable
etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.

Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RGMII modes delays can be set via strapping pings or EEPROM.
Don't change them unless explicitly asked to change them.  The recent
refactoring of setting the MAC configuration changed this behaviours,
in that CPU and DSA ports have any pre-configured RGMII delays
removed. This breaks the Armada 370RD board. Restore the previous
behaviour, in that RGMII delays are only applied/removed when
explicitly asked for via an phy-mode being PHY_INTERFACE_MODE_RGMII*

Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

The previous implementation of set_settings was modifying
the value of advertising, but with the new API, it's not
possible. The structure ethtool_link_ksettings is defined
as const.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to stop ctlr if it was already stopped. It can cause timeout
warns. Steps:
- ifconfig eth0 down
- ethtool -l eth0 rx 8 tx 8
- ethtool -l eth0 rx 1 tx 1
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dma ctlr is reseted to 0 while cpdma soft reset, thus cpdma ctlr
cannot be configured after cpdma is stopped. So restoring content
of cpdma ctlr while off/on procedure is needed. The cpdma ctlr off/on
procedure is present while interface down/up and while changing number
of channels with ethtool. In order to not restore content in many
places, move it to cpdma_ctlr_start().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The field is 7bit long. Fix it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The idr_alloc(), idr_remove(), et al. routines all expect IDs to be
signed integers.  Therefore make the genl_family member 'id' signed
too.
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of remembering if the page was changed, just compare the current
page to the saved one. This is easier and has the advantage to save a
register write if the page was already restored.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2016-11-10

This patch series is targeted at adding support for a new PCI version
of the hardware. As part of the new PCI device, there is a new PCS/PHY
interaction, ECC support, I2C sideband communication, SFP+ support and
more.

The following updates and fixes are included in this driver update series:

- Hardware workaround for possible incorrectly generated interrupts
  during software reset
- Hardware workaround for Tx timestamp register access order
- Add support for a PCI version of the device
- Increase the Rx queue limit to take advantage of the increased number
  of DMA channels that might be available
- Add support for a new DMA channel interrupt mode
- Add ECC support for the device memory
- Add support for using the integrated I2C controller for sideband
  communication
- Expose the phylib phy_aneg_done() function so it can be called by the
  driver
- Add support for SFP+ modules
- Add support for MDIO attached PHYs
- Add support for KR re-driver between the PCS/SerDes and an external
  PHY

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides support for the presence of a KR redriver chip in
between the device PCS and an external PHY.  When a redriver chip is
present the device must perform clause 73 auto-negotiation in order to
set the redriver chip for the downstream connection.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the phylib support in the kernel to communicate with and control an
MDIO attached PHY. Use the hardware's MDIO communication mechanism to
communicate with the PHY.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for recognizing and using SFP+ modules directly. This includes
using the I2C support to read and interpret the information returned from
an SFP+ module and configuring things properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.

Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to initialize and use the I2C controller within the hardware
in order to perform sideband communication, e.g. determine the SFP media
type that is installed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some versions of the amd-xgbe device are capable of reporting ECC error
information back to the driver. Add support to process, track and report
on this information.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current per channel DMA interrupt support is based on an edge
triggered interrupt that is not maskable. This results in having to call
the disable_irq/enable_irq functions in order to prevent interrupts
during napi processing. The hardware now has a way to configure the per
channel DMA interrupt that will allow for masking the interrupt which
prevents calling disable_irq/enable_irq now. This patch makes use of
this support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the call to netif_get_num_default_rss_queues() and replace it
with num_online_cpus() to allow for the possibility of using all of
the hardware DMA channels available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for new PCI devices to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the reading of the Tx timestamp to account for a hardware issue
on how the fields and interrupt are cleared.  The "seconds" portion of
the timestamp should be read first, followed by the "nanoseconds" portion.
Reading the "nanoseconds" portion should clear the timestamp data and the
interrupt.  Because of an issue with the hardware this order is reversed
and reading the "seconds" portion actually clears the timestamp.  The code
currently follows this workaround, but to guard against future versions
where this is fixed add a field to the version data to indicate if the
workaround is required or not.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a hardware issue, it is possible for interrupt events to be
incorrectly generated when performing a soft reset.  To guard against
this, perform the soft reset twice.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Benc says:

====================
openvswitch: support for layer 3 encapsulated packets

At the core of this patch set is removing the assumption in Open vSwitch
datapath that all packets have Ethernet header.

The implementation relies on the presence of pop_eth and push_eth actions
in datapath flows to facilitate adding and removing Ethernet headers as
appropriate. The construction of such flows is left up to user-space.

This series is based on work by Simon Horman, Lorand Jakab, Thomas Morin and
others. I kept Lorand's and Simon's s-o-b in the patches that are derived
from v11 to record their authorship of parts of the code.

Changes from v12 to v13:

* Addressed Pravin's feedback.
* Removed the GRE vport conversion patch; L3 GRE ports should be created by
  rtnetlink instead.

Main changes from v11 to v12:

* The patches were restructured and split differently for easier review.
* They were rebased and adjusted to the current net-next. Especially MPLS
  handling is different (and easier) thanks to the recent MPLS GSO rework.
* Several bugs were discovered and fixed. The most notable is fragment
  handling: header adjustment for ARPHRD_NONE devices on tx needs to be done
  after refragmentation, not before it. This required significant changes in
  the patchset. Another one is stricter checking of attributes (match on L2
  vs. L3 packet) at the kernel level.
* Instead of is_layer3 bool, a mac_proto field is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow ARPHRD_NONE interfaces to be added to ovs bridge.

Based on previous versions by Lorand Jakab and Simon Horman.
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's not allowed to push Ethernet header in front of another Ethernet
header.

It's not allowed to pop Ethernet header if there's a vlan tag. This
preserves the invariant that L3 packet never has a vlan tag.

Based on previous versions by Lorand Jakab and Simon Horman.
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the ovs flow netlink protocol to support L3 packets. Packets without
OVS_KEY_ATTR_ETHERNET attribute specify L3 packets; for those, the
OVS_KEY_ATTR_ETHERTYPE attribute is mandatory.

Push/pop vlan actions are only supported for Ethernet packets.

Based on previous versions by Lorand Jakab and Simon Horman.
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support receiving, extracting flow key and sending of L3 packets (packets
without an Ethernet header).

Note that even after this patch, non-Ethernet interfaces are still not
allowed to be added to bridges. Similarly, netlink interface for sending and
receiving L3 packets to/from user space is not in place yet.

Based on previous versions by Lorand Jakab and Simon Horman.
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update Ethernet header only if there is one.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll need it to alter packets sent to ARPHRD_NONE interfaces.

Change do_output() to use the actual L2 header size of the packet when
deciding on the minimum cutlen. The assumption here is that what matters is
not the output interface hard_header_len but rather the L2 header of the
particular packet. For example, ARPHRD_NONE tunnels that encapsulate
Ethernet should get at least the Ethernet header.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a hole in the structure. We support only Ethernet so far and will add
a support for L2-less packets shortly. We could use a bool to indicate
whether the Ethernet header is present or not but the approach with the
mac_proto field is more generic and occupies the same number of bytes in the
struct, while allowing later extensibility. It also makes the code in the
next patches more self explaining.

It would be nice to use ARPHRD_ constants but those are u16 which would be
waste. Thus define our own constants.

Another upside of this is that we can overload this new field to also denote
whether the flow key is valid. This has the advantage that on
refragmentation, we don't have to reparse the packet but can rely on the
stored eth.type. This is especially important for the next patches in this
series - instead of adding another branch for L2-less packets before calling
ovs_fragment, we can just remove all those branches completely.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On tx, use hard_header_len while deciding whether to refragment or drop the
packet. That way, all combinations are calculated correctly:

* L2 packet going to L2 interface (the L2 header len is subtracted),
* L2 packet going to L3 interface (the L2 header is included in the packet
  lenght),
* L3 packet going to L3 interface.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 67f8b1dc ("net/mlx4_en: Refactor the XDP forwarding rings
scheme") added a bug in that the prog's reference count is not dropped
in the error path when mlx4_en_try_alloc_resources() is failing from
mlx4_xdp_set().

We previously took bpf_prog_add(prog, priv->rx_ring_num - 1), that we
need to release again. Earlier in the call path, dev_change_xdp_fd()
itself holds a reference to the prog as well (hence the '- 1' in the
bpf_prog_add()), so a simple atomic_sub() is safe to use here. When
an error is propagated, then bpf_prog_put() is called eventually from
dev_change_xdp_fd()

Fixes: 67f8b1dc ("net/mlx4_en: Refactor the XDP forwarding rings scheme")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While create/destroy channel operation memory is not freed. It was
supposed that memory is freed while driver remove. But a channel
can be created and destroyed many times while changing number of
channels with ethtool.

Based on net-next/master
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Bug fixes & Code improvements in HNS driver

This patch-set introduces some bug fixes and code improvements.
These have been identified during internal review or testing of
the driver by internal Hisilicon teams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support to add or remove the unicast entries
to the table and remove from the table.
Reported-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no clear operation before add a new multicast tcam table,
so the tcam table will be overflow when add more entries.
Reported-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The packets of wrong mac address(only the last bit is different) can be
received in Big-endian by current definition of mask_key. Thus it needs
to be modified to support Big-endian and ensure Big-endian normal.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current definition of mac_mc_entry is only suitable for
Little-endian. Thus it needs to modify tcam table of mac mc-entry
to support both Little-endian and Big-endian.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Little-endian is only supported by current tcam table to add
or delete mac mc-port. This patch makes it support both
Little-endian and Big-endian.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Big-endian is not supported by the current definition of table index to get
mac entry. It needs to be modified to support both Little-endian
and Big-endian.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>