- 09 Aug, 2011 21 commits
-
-
Alex Hacker authored
Signed-off-by: Alex Hacker <hacker@epn.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Add code to display driver version information in dmesg after loading the driver successfully. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Drake authored
The SDIO card is now fully powered down when the network interface is brought down. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Drake authored
Modify the driver so that it does not function when the interface is down, in preparation for runtime power management. No commands can be run while the interface is down, so the ndo_dev_stop routine now directly does all necessary work (including asking the device to disconnect from the network and disabling multicast functionality) directly. power_save and power_restore hooks are added meaning that card drivers can take steps to turn the device off when the interface is down. The MAC address can now only be changed when all interfaces are down; the new address will be programmed when an interface gets brought up. This matches mac80211 behaviour. Also, some small cleanups/simplifications were made in the surrounding device handling logic. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Some drivers (ath9k for example) are using skb->protocol to treat EAPOL frames somehow special (disallow aggregation for example). When running in AP mode hostapd injects the EAPOL frames through a monitor interface and thus skb->protocol isn't set at all. Hence, if the injected frame is a data frame and carries a rfc1042 headaer update the skb->protocol field accordingly. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Several uses were missing terminating newlines. Typo fix and macro neatening. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
The high_power tx gain table is changed to match the low_ob_db tx gain table for both 5G and 2G. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
No need to process RxDone and ds_info status again in case valid rx status is given. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
This patch cleanups virtual wiphy specific frametype structure Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k/modal_eeprom Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k/base_eeprom Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Hauke Mehrtens authored
This ieee80211 core was found on a Netgear wndr3400. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
They are SPROM specific, so all should be defined in ssb code. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 08 Aug, 2011 19 commits
-
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Currently ath9k presents the internal calibrated noise floor as channel noise measurement, however this results in highly chip specific values that are only useful as relative measurements but do not resemble any real channel noise values. In order to give a much better approximation of the real channel noise, add the difference between the measured noise floor and the nominal chip specific noise floor to the default minimum channel noise value, which is currently used to calculate the signal strength from the RSSI value. This may not be 100% accurate, but it's much better than what's there before. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Baruch Siach authored
Make mesh_preq_queue_lock locking consistent with mesh_queue_preq() using spin_lock_bh(). Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Drake authored
OLPC power management code has recently gone upstream. This piece completes the puzzle for libertas_usb, which now programs the OLPC EC for wlan wakeups when they have been requested. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
When testing for tx power, bypass the default limits. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Use the previously calculated maximum of all rates instead of just the one from the lowest rate of the selected PHY mode. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
It is always 0 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Remove unnecessary includes from base.h. Add includes to other files as necessary. Don't include base.h unless needed. Move declarations for functions in base.c from ath5k.h to base.h. Use a better named define to protect base.h against double inclusion. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01" as the third product ID. Those have Agere firmware. With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be assumed to have Intersil firmware. Cards with Agere firmware use "Version 01.01". Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
This is needed to match wireless cards with Intersil firmware that have ID 0x0156:0x0002 and the third ID "Version 01.02". Such cards are currently matched by orinoco_cs, which doesn't support WPA. They should be matched by hostap_cs. The first and the second product ID vary widely, so there are few users with some particular IDs. Of those, very few can submit a patch for hostap_cs or write a useful bugreport. It's still important to support their hardware properly. With PCMCIA_DEVICE_MANF_CARD_PROD_ID3, it should be possible to cover the remaining Intersil based designs that kept the numeric ID and the "version" of the reference design. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
According to 802.11-2007, 7.3.1.14 it is compliant to use a buf_size of 0 in ADDBA requests. But some devices (AVM Fritz Stick N) arn't able to handle that correctly and will reply with an ADDBA reponse with a buf_size of 0 which in turn will disallow BA sessions for these devices. To work around this problem, initialize hw.max_tx_aggregation_subframes to the maximum AMPDU buffer size 0x40. Using 0 as default for the bufsize was introduced in commit 5dd36bc9 (mac80211: allow advertising correct maximum aggregate size). Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
If we receive an ADDBA response with status code 0 and a buf_size of 0 we should stop the TX BA session as otherwise we'll end up queuing frames in ieee80211_tx_prep_agg forever instead of sending them out as non AMPDUs. This fixes a problem with AVM Fritz Stick N wireless devices where frames to this device are not transmitted anymore by mac80211. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Devices supported by b43legacy don't support 64-bit DMA. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Add support for v2 of enhanced sensitivity table for 2000 series products Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Update the default sensitivity value for both 5000 and 6000 series devices Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-