- 26 Feb, 2010 40 commits
-
-
Guennadi Liakhovetski authored
Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Use soc_camera_apply_sensor_flags() in mt9v022 to account for any inverters in video signal paths. Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/dvb/dvb-usb/az6027.c:759: warning: ‘az6027_read_mac_addr’ defined but not used While there's some code that uses it, it is currently commented. So, comment also the function itself. CC: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: -
Mauro Carvalho Chehab authored
drivers/media/dvb/dvb-usb/az6027.c:390: warning: excess elements in struct initializer drivers/media/dvb/dvb-usb/az6027.c:390: warning: (near initialization for ‘az6027_rc_keys[0]’) drivers/media/dvb/dvb-usb/az6027.c:391: warning: excess elements in struct initializer drivers/media/dvb/dvb-usb/az6027.c:391: warning: (near initialization for ‘az6027_rc_keys[1]’) CC: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: -
Manu Abraham authored
Signed-off-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
-
Adams Xu authored
Signed-off-by:
-
Huang Shijie authored
video : use the V4L2_STD macros to select the proper audio setting. radio : add preemphasis ctr. test it by the command: v4l2-ctl -d /dev/radio0 --set-ctrl=pre_emphasis_settings=1 [mchehab@redhat.com: folded documentation patch] Signed-off-by:
Huang Shijie <shijie8@gmail.com> Signed-off-by:
-
Huang Shijie authored
pd-common.h contains the common data structures, while vendorcmds.h contains the vendor commands for firmware. [mchehab@redhat.com: Folded the 10 patches with the driver] Signed-off-by:
-
Franklin Meng authored
Adds remote support for the Kworld 315U device I have added the change for the IR_TYPE_NEC that Mauro suggested. Note: I believe I got most of the mappings correct. Though the source and shutdown button probably could be mapped to something better. [mchehab@redhat.com: Fix CodingStyle] Signed-off-by:
Franklin Meng <fmeng2002@yahoo.com> Signed-off-by:
-
Darren Jenkins authored
In si470x_usb_driver_disconnect() radio->disconnect_lock is accessed after it is freed. This fixes the problem. Coverity CID: 2530 Signed-off-by:
Darren Jenkins <darrenrjenkins@gmail.com> Signed-off-by:
-
Antti Palosaari authored
There is no driver for new NXP TDA18218 tuner which is used by few recent af9015 designs. af9015 uses number 179 as ID for that tuner. Inform this tuner is not supported when device using that tuner is meet. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Autodetect MYGICTV U718 from eeprom hash and select remote automatically. Remove old iManufacturer string compare based remote selection logic. Signed-off-by:
-
Antti Palosaari authored
Autodetect A-Link DTU(m) based eeprom hash and select correct remote. Signed-off-by:
-
Antti Palosaari authored
Add USB ID 0413:6a04 for Leadtek WinFast DTV2000DS. Thanks to Gavin Ramm <gavin_ramm@hotmail.com> for reporting this. Signed-off-by:
-
Antti Palosaari authored
Add USB ID 1b80:e402 for DigitalNow TinyTwin version 2. Thanks to Trevor Phillips <trevor.phillips@gmail.com> for reporting this. Signed-off-by:
-
Jiri Slaby authored
Switch second and third memset parameter to stamp the length buffer bytes by 0xff's, not 255 bytes by low 8 bits of Length. Cc: linux-media@vger.kernel.org, linux-kernel@vger.kernel.org, jirislaby@gmail.com, Matthias Benesch <twoof7@freenet.de>, Ralph Metzler <rjkm@metzlerbros.de>, Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Matthias Benesch <twoof7@freenet.de> Cc: Ralph Metzler <rjkm@metzlerbros.de> Cc: Oliver Endriss <o.endriss@gmx.de> Cc: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
-
Andrea.Amorosi76@gmail.com authored
Adds digital and analogue tv support for Dikom DK300 hybrid usb card. Not working: remote controller To be done: it seems that with the proposed patch the digital demodulator remains activated if the tuner is switched from digital to analogue mode. Workaround is to unplug and replug the device when switching from digital to analogue. If someone can explain how to verify the gpio settings using the usbsnoop, the above issue perhaps can be resolved. Signed-off-by:
Andrea Amorosi <Andrea.Amorosi76@gmail.com> Signed-off-by:
-
Julia Lawall authored
In each case, the NULL test has been performed already. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ expression *x; expression e; identifier l; @@ if (x == NULL || ...) { ... when forall return ...; } ... when != goto l; when != x = e when != &x *x == NULL // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Klaas de Waal authored
Remove check "state->dst_type == DST_DTYPE_IS_CABLE" in function dst_get_tuna (around line 1352) to select the correct checksum computation Fill in the .caps field in struct dst_dvbc_ops (around line 1824) with all the supported QAM modulation methods to match the capabilities of the card as implemented in function dst_set_modulation (around line 502). Note that beginning with linux kernel version 2.6.32 the modulation method is checked (by function dvb_frontend_check_parameters in file drivers/media/dvb/dvb-core/dvb_frontend.c) and thus tuning fails if you use a modulation method that is not present in the .caps field. This patch has been tested on a Twinhan VP2031A DVB-C card with the 2.6.32.2 kernel. Signed-off-by:
Klaas de Waal <klaas.de.waal@gmail.com> Signed-off-by:
-
Sean Young authored
When capturing NTSC, the saa7134 can capture 720x480. While doing Laserdisc captures using this card, I noticed that right side was truncated/cropped. The highest geometry the driver allows is 704x480, even though in Windows XP it is 720x480. This results in no cropping and the same results as in Windows. Tested on an AverMedia GO 007 FM Plus. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Abylay Ospan authored
if the AGC2 > 1400 then no signal on this frequency for STV0900 Cut 3.0. For Cut 2.0 this value is 700. Signed-off-by:
Abylay Ospan <aospan@netup.ru> Signed-off-by:
-
Douglas Schilling Landgraf authored
As pointed by Magnus Alm <magnus.alm@gmail.com>, commit 99dbd128bb applied a hunk at the wrong place. This patch moves the code to the right place. Signed-off-by: -
Oliver Endriss authored
Commiter: Oliver Endriss <o.endriss@gmx.de> Fix typo. Sort list of components for better readability. Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Oliver Endriss authored
Commiter: Oliver Endriss <o.endriss@gmx.de> Use 'get_dvb_firmware ngene' to download 'ngene_15.fw' and 'ngene_17.fw'. Signed-off-by:
-
Stephen Rothwell authored
After merging the scsi-post-merge tree, today's linux-next build (powerpc allyesconfig) failed like this: drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_release_buffers': drivers/media/dvb/ngene/ngene-core.c:1443: error: implicit declaration of function 'vfree' drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_get_buffers': drivers/media/dvb/ngene/ngene-core.c:1454: error: implicit declaration of function 'vmalloc' drivers/media/dvb/ngene/ngene-core.c:1454: warning: assignment makes pointer from integer without a cast drivers/media/dvb/ngene/ngene-core.c:1461: warning: assignment makes pointer from integer without a cast drivers/media/dvb/ngene/ngene-core.c:1467: warning: assignment makes pointer from integer without a cast drivers/media/dvb/ngene/ngene-core.c: In function 'ngene_probe': drivers/media/dvb/ngene/ngene-core.c:1836: warning: assignment makes pointer from integer without a cast Caused by commit b54c755d6263efe376f3dfc8c72c8e7b4fb4f4c1 ("V4L/DVB: ngene: Initial check-in"). Signed-off-by:Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Richard Röjfors authored
The timberdale FPGA is found on the Intel in-Vehicle Infotainment reference board russelville. The driver is a PCI driver which chunks up the I/O memory and distributes interrupts to a number of platform devices for each IP inside the FPGA. Signed-off-by:
Richard Röjfors <richard.rojfors@pelagicore.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Richard Röjfors authored
This patch add supports for the radio system on the Intel Russellville board. It's a In-Vehicle Infotainment board with a radio tuner and DSP. This umbrella driver has the DSP and tuner as V4L2 subdevs and calls them when needed. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Oliver Endriss authored
Use I2C_CLASS_TV_DIGITAL, not I2C_ADAP_CLASS_TV_DIGITAL. Remove initialisation of bus_lock mutex. Thanks to Mauro for pointing out. Signed-off-by:
-
Oliver Endriss authored
Make checkpatch.pl happy. Signed-off-by:
-
Oliver Endriss authored
Cards 18c3:abc3/18c3:abc4 should be displayed as 'Linux4Media cineS2'. Signed-off-by:
-
Oliver Endriss authored
Request might already have been processed when the interrupt arrives. Signed-off-by:
-
Oliver Endriss authored
Implement workaround for comamnd timeout. Use FW15 and avoid switching DMA on and off. Signed-off-by:
-
Oliver Endriss authored
Set ADC1 and ADC2 range of the stv0900 to 1Vpp. Signed-off-by:
-
Oliver Endriss authored
Adapt to current stv090x + stv6110 drivers. [mchehab@redhat.com: removed compilation hack added by me on a prev patch] Signed-off-by:
-
Matthias Benesch authored
Identify card 18c3:db01 as 'Mystique SaTiX-S2 Dual'. Signed-off-by:
Matthias Benesch <twoof7@freenet.de> Signed-off-by:
-
Manu Abraham authored
Trivial I2C related fixes/cleanups - Remove Unused I2C ID - point the I2C device to the physical device Signed-off-by:
-
Oliver Endriss authored
Remove/comment-out unused code, make some functions/declarations static. Signed-off-by:
-
