- 18 May, 2018 1 commit
-
-
Kieran Bingham authored
The Salvator boards use an ADV7482 receiver for HDMI and CVBS inputs. Provide ADV7482 node on the i2c4 bus, along with connectors for the hdmi and cvbs inputs, and link to the csi20 and csi40 nodes as outputs. Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
- 16 May, 2018 39 commits
-
-
Niklas Söderlund authored
Signed-off-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Niklas Söderlund authored
Renesas H3 ES1.0 have one extra CSI-2 node, CSI21 which is not present for later ES versions of H3. Signed-off-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Yoshihiro Shimoda authored
This patch enables EthernetAVB for r8a77990 Ebisu board. Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This patch adds EthernetAVB node for r8a77990 (R-Car E3). Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This patch adds GPIO nodes for r8a77990 (R-Car E3). Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This patch adds PFC device node for r8a77990 (R-Car E3). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Sergei Shtylyov authored
Add the initial device tree for the V3H Starter Kit board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by:
Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Sergei Shtylyov authored
When adding the R8A77980 EtherAVB device I failed to notice that it does not have the usual "status" property disabling the described devices in anticipation that the board device trees enable the devices according to their needs. This causes the EtherAVB driver to successfully probe despite e.g. the needed pins not having been configured -- luckily, "eth<n>" device can't be opened anyway... Fixes: bf6f9083 ("arm64: dts: renesas: r8a77980: add EtherAVB support") Signed-off-by:
-
Sergei Shtylyov authored
When adding the R8A77970 EtherAVB device I failed to notice that it does not have the usual "status" property disabling the described devices in anticipation that the board device trees enable the devices according to their needs. This causes the EtherAVB driver to successfully probe despite e.g. the needed pins not having been configured -- luckily, "eth<n>" device can't be opened anyway... Fixes: bea2ab13 ("arm64: dts: renesas: r8a77970: add EtherAVB support") Signed-off-by:
-
Jacopo Mondi authored
Describe VIN4 interface for R-Car D3 R8A77995 SoC. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by:
-
Simon Horman authored
Add resets property to CAN-FD node to describe it in the reset topology of on-SoC devices. This allows to reset the CAN-FD device using the Reset Controller API. Signed-off-by:
-
Geert Uytterhoeven authored
Enable the performance monitor unit for the Cortex-A53 cores on the R-Car V3M (r8a77970) SoC. Signed-off-by:
-
Geert Uytterhoeven authored
Add a device node for the second Cortex-A53 CPU core on the Renesas R-Car V3M (r8a77970) SoC, and adjust the interrupt delivery masks for ARM Generic Interrupt Controller and Architectured Timer. Signed-off-by:
-
Takeshi Kihara authored
Add SDHI nodes to the DT of the r8a77965 SoC. Based on several similar patches of the R8A7796 device tree by Simon Horman <horms+renesas@verge.net.au>. Signed-off-by:
Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by:
Yoshihiro Kaneko <ykaneko0929@gmail.com> Reviewed-by:
-
Geert Uytterhoeven authored
On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and DDR1C power rails need to be kept powered when backup mode is enabled. Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node. The accessory power switch (SW8) is a momentary switch, hense specify "rohm,rstbmode-pulse". Signed-off-by:
-
Geert Uytterhoeven authored
On Salvator-X(S), all of the DDR0, DDR1, DDR0C, and DDR1C power rails need to be kept powered when backup mode is enabled. Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node. The accessory power switch (SW23) is a toggle switch, hence specify "rohm,rstbmode-level". Signed-off-by:
-
Geert Uytterhoeven authored
Add a device node for the ROHM BD9571MWV PMIC. This was based on the example in the DT binding documentation, but using IRQ0 instead of a GPIO interrupt, as that matches the schematics, and because INTC-EX is a simpler block. Signed-off-by:
-
Geert Uytterhoeven authored
Add missing space after comma. Signed-off-by:
-
Geert Uytterhoeven authored
Add missing spaces after commas. Signed-off-by:
-
Geert Uytterhoeven authored
Add missing spaces after commas. Replace 8 consecutive spaces by a TAB. Signed-off-by:
-
Yoshihiro Shimoda authored
This patch enables USB2.0 host channel 3 for r8a7795 with Salvator-XS. Signed-off-by:
-
Yoshihiro Shimoda authored
This patch enables HS-USB channel3 node for r8a7795 with Salvator-XS. Signed-off-by:
-
Yoshihiro Shimoda authored
This patch enables usb2_phy3 node for r8a7795 with Salvator-XS. You must change the SW31 to OFF-OFF-ON-ON-ON-ON on the board. Signed-off-by:
-
Wolfram Sang authored
Add the EEPROM found on Salvator-X and -XS boards for H3, M3-W, and M3-N on the IIC_DVFS bus. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Sergei Shtylyov authored
Define the Condor board dependent part of the CAN-FD device node. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by:
-
Sergei Shtylyov authored
Define the generic R8A77980 part of the CAN-FD device node. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by:
-
Sergei Shtylyov authored
Define the Eagle board dependent part of the CAN-FD device node. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by:
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by:
-
Sergei Shtylyov authored
Define the generic R8A77970 part of the CAN-FD device node. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by:
-
Niklas Söderlund authored
Based on previous work by Ryo Kataoka <ryo.kataoka.wt@renesas.com>. Signed-off-by:
-
Niklas Söderlund authored
Replace the hardcoded power domain indices by R8A77965_PD_* symbols. Signed-off-by:
Jacopo Mondi <jacopo@jmondi.org> [simon: dropped hunk to include r8a77965-sysc.h which is already present] Signed-off-by:
-
Sergei Shtylyov authored
Now that the commit 7755b40d ("dt-bindings: power: add R8A77980 SYSC power domain definitions") has hit Linus' tree, we can replace the bare numbers (we had to use to avoid a cross tree dependency) with these macro definitions... Signed-off-by:
-
Sergei Shtylyov authored
Now that the commit 35b3c462 ("dt-bindings: clock: add R8A77980 CPG core clock definitions") has hit Linus' tree, we can replace the bare numbers (we had to use to avoid a cross tree dependency) with these macro definitions... Signed-off-by:
-
Simon Horman authored
The rcar_sound port nodes have unit names and thus should have register properties. This is flagged by dtc as follows: # make dtbs W=1 ... DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property DTC arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property Prior to this patch the port nodes only defined in board DTS files. As the register properties are common this patch defines the port nodes and provides register properties in the SoC DTS file. Signed-off-by:
-
Simon Horman authored
The rcar_sound port nodes have unit names and thus should have register properties. This is flagged by dtc as follows: # make dtbs W=1 ... DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property ... DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property Prior to this patch the port nodes only defined in board DTS files. As the register properties are common this patch defines the port nodes and provides register properties in the SoC DTS file. Signed-off-by:
-
