Increasing the reply frame size by 16 bytes, to
be in sync with the other fusion drivers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.

The timeout selection should probably be done in a little helper instead
of duplicated in a few places.  Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Increase the port enable timeout only for SAS from 30 to 300 seconds.
A customer request for the handling large topologies.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch is for spi.  This issues bus reset when driver
loads. Handling cases when initator has negotiated for packetized,
and target negotiated for non-packetized; effectly this bus reset
is getting both target and initiator on the same sheet of music.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix the timer handling in aic79xx to use the SCSI-ML provided handling
instead of implementing our own.
It also fixes a deadlock in the command recovery code.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch updates the documentation for aic7xxx and aic79xx with fixes
from the adaptec driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch introduces the SLOWCRC handling for certain buggy chipsets.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch updates the aic79xx sequencer with latest fixes from adaptec.
The sequencer code now corresponds with adaptec version 2.0.15.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patchset updates aicasm code with the latest fixes from adaptec.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The prior fusion patches moved an invocation of a function,
mptscsih_TMHandler(), static to mptscsih.c into mptsas.c

Make the function unstatic, move the header to mptscsih.h and export it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This fix's problems with recent fc submission regarding
i/o being redirected to the wrong target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This moves code intented for SAS from
the generic mptscsih module over to the
mptsas module.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The issuing of the target reset
used in device hot removal case so the
firmware queue is flushed out off outstanding
commands.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

RAID event support.

This will hot add and remove raid volumes
when managment application creates and
deletes the volumes.  The driver is basically
responding to firmware asyn events, and reporting
the changes to the above layers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch displays the port identifier on
the folder attribute; located in the middle digit.

/sys/class/sas_rphy/rphy-%x:%x:%x

The port identifier is basically the unique identifier
for each sas domain.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch defines a new template to represent each type of
controllers (identified by the processor used). The template has
members that is set with appropriate values during driver
initialisation. This change is done to support new controllers with
minimal change to existing code. In future, for a new controller
support, a template will be declared and its members initialised
appropriately.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>

Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch (originally submitted by Christoph Hellwig) removes code
duplication in megasas_build_cmd.  It also defines
MEGASAS_IOC_FIRMWARE32 to allow 64 bit compiled applications to work.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>

Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Resetting the adapter causes the ServeRAID driver to exceed
the max time allowed by the softlock watchdog. Resetting the
hardware can easily require 30 or more seconds. To avoid the

    "BUG: soft lockup detected on CPU#0!"

result, this patch replaces the mdelay() calls in the
initialization/reset routines with msleep().
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Internal lun discovery has been removed since fc_transport
integration.  Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread.  Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT].  Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue.  If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport.  The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE
case. I put "fixes" in quotes because the real fix would be to completely
remove it, but that's beyond the scope of this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

New versions of the Power5 firmware can send a "re-enable" message to
the virtual scsi adapter.  This fix makes us handle the message
correctly.  Without it, the driver goes catatonic and the system crashes
unpleasantly.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Remove support for kernels older than 2.6.0.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

The compat layer timeout handling changes in:

9f72949f

are busted.  This is most easily seen with an X application
that uses sub-second select/poll timeout such as emacs.  You
hit a key and it takes a second or so before the app responds.

The two ROUND_UP() calls upon entry are using {tv,ts}_sec where it
should instead be using {tv_usec,ts_nsec}, which perfectly explains
the observed incorrect behavior.

Another bug shot down with git bisect.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Or else we break on ppc32 and other 32-bit platforms.

Based upon a patch from Harald Welte.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix an unnecessary softlockup watchdog warning in the ia64
uncached_build_memmap() that occurs occasionally at 256p and always at
512p.  The problem occurs at boot time.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Migrate perfmon from using an old semaphore to a completion handler.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Migrate arch/ia64/ia32/sys_ia32 to using a mutex for mmap protection.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

This also includes by necessity _TIF_RESTORE_SIGMASK support,
which actually resulted in a lot of cleanups.

The sparc signal handling code is quite a mess and I should
clean it up some day.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

some driver clean ups, and a re-posting of changes that are needed

to match the updated TPS.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>