* remove netif_queue_stopped test, netif_wake_queue already does that
* move vlan stuff to top of file
* remove __dev markers
* update todo list at top of file
* remove pci_set_dma_mask argument casts; ULL suffixes preferred.

NAPI is turned on unconditionally for the RX path.  The hardware
supports interrupt mitigation, so that should be investigated too.

RX fragment handling removed.  We simply ensure that we alloc
buffers large enough to hold incoming packets.  Any stray RX
frags that occur (shouldn't be any) will be dropped.

(previously it was ifdef'd)

Also, bump version to 1.0.

Missing pieces for DMA-API on the Rx side:
- SiS190_init_ring: the global area for the received data is mapped.
  This area is persistent during the whole driver's life.
  It only needs to be unmapped in SiS190_close() as no other exit/error
  path exists.
- SiS190_rx_interrupt: no map/unmap for received data buffer. A single
  sync operation is done. Btw, there is no need to store the same value
  in RxDescArray[cur_rx].buf_addr over and over again.
- Remove driver dependancy on CONFIG_BROKEN.

* call pci_set_dma_mask
* remove erroneous call to unregister_netdev in _init_board()

I realized that I've had this patch in my tree for a while, and forgot
to send it to you and lkml.  The patch below fixes bug number 923:
	http://bugme.osdl.org/show_bug.cgi?id=923
(basically keeps us from calling pci_find_device from interrupt
context.)

It's been tested by a few people with this device, and they say it works
just fine for them.  Please forward it on up the food chain.

instead of homebrew MII bitbanging.

Driver does not need to enforce 256 byte alignment for data returned
from pci_alloc_consistent().
- {rx/tx}_dma_aligned and {rx/td}_dma_raw are both replaced by {rx/tx}_dma;
- {rx/tx}_desc_raw is replaced by direct use of {Rx/Tx}DescArray;
- SiS190_open()
  + fixup for a lack of kmalloc() failure handling;
  + (return status) there is no need for both retval/rc: merge them;
  + anonymous printk() fixup: the name of the guilty device is printed;
- define {RX/TX}_DESC_TOTAL_SIZE because I am too lazy to read twice the
  same lengthy arithmetic expression.

Also, export PCI bus id via ETHTOOL_GDRVINFO.

Drivers updated: fmvj18x_cs, ibmtr_cs, nmclan_cs, pcnet_cs,
xirc2ps_cs.

Until RX path is cleaned up to use PCI DMA API and
not virt_to_bus.

Also, minor changes:
* mark ->hard_start_xmit ETH_ZLEN test as unlikely()
* use cpu_to_le32() and le32_to_cpu() in TX path
* fix two leak in error path, in ->hard_start_xmit
* don't test netif_queue_stopped() in TX completion path,
  netif_wake_queue() already does that.

Looks like this driver wasn't tested on SMP :)

older gcc's do not support C99/C++ style of variable declarations.

sound/pcmcia/vx/vx_entry.c:

This patch removes the PCMCIA timer release functionality which is no
longer required. Without this the module does not compile.

Too much cut-and-paste, noticed by Dmitry Torokhov <dtor_core@ameritech.net>

into samba.org:/home/paulus/kernel/for-linus-ppc

On PPC32 we reorder the arguments so they fit into 6 registers.  Glibc will
need a two-line stub to change them from the standard order to the ordering
used by the system call: (fd, advice, offset, len).

into samba.org:/home/paulus/kernel/for-linus-ppc