Provide default activate function to set the state of the led
when the led becomes bound to the trigger
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow the rfkill driver to specify led trigger name.
By default it still defaults to the name of rfkill switch.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Every time a new input device that is capable of one of the
rfkill EV_SW events (currently only SW_RFKILL_ALL) is connected to
rfkill-input, we must check the states of the input EV_SW switches
and take action.  Otherwise, we will ignore the initial switch state.

We also need to re-check the states of the EV_SW switches after
a device that was under an exclusive grab is released back to us,
since we got no input events from that device while it was grabbed.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Enable I/Q calibration each time we have correction results (we
   were only enabling calibration during reset). If we don't we commit
   the same results each time calibration routine is called.
 * Add some documentation and a TODO on nf calibration
 * Return -EAGAIN on noise floor timeout/failure

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Add channel function for RF2425 (got this from decompiling binary
   HAL, i have no idea why there is a 5GHz section but i'm looking
   into it)
 * Update RF5112 channel function (also got this from decompiling binary HAL)
 * Set JAPAN setting for channel 14 on all PHY chips

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Add initial RF gain settings for RF2425

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Update ath5k_hw_reset and add some more documentation about PHY calibration
 * Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
 * Preserve sleep duration field while setting AR5K_SLEEP_CTL
   and reduce delays & checks for register's status (got this from
   decompiling & dumps, it works for me but it needs testing)

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Do an ADC test during reset to match recent regdumps

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Update hw_reset to calculate some of the values we were using as static
 * Increase activation to rx delay

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Correctly attach RF2425
 * Update SREV values for Radio chips
 * Update hw_attach to use new SPENDING values
 * Write a bit after POST for some chips

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * Restore saved initial value after POST

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c

Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported by Stefanos Harhalakis; although 2.6.27-rc1 talks to itself using IPv6
TCP MD5 packets just fine, Stefanos noted that tcpdump claimed that the
signatures were invalid.

I broke this in 49a72dfb ("tcp: Fix MD5
signatures for non-linear skbs"), it was just a typo.

Note that tcpdump will still sometimes claim that the signatures are incorrect.
A patch to tcpdump has been submitted for this[1].

[1] http://tinyurl.com/6a4fl2Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing kernel-doc notation to sk_buff:

Warning(linux-2.6.27-rc1-git2//include/linux/skbuff.h:345): No description found for parameter 'do_not_encrypt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix:

net/ipv4/route.c: In function 'ip_static_sysctl_init':
net/ipv4/route.c:3225: error: 'ipv4_route_path' undeclared (first use in this function)
net/ipv4/route.c:3225: error: (Each undeclared identifier is reported only once
net/ipv4/route.c:3225: error: for each function it appears in.)
net/ipv4/route.c:3225: error: 'ipv4_route_table' undeclared (first use in this function)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

I noticed, looking at tcpdumps, that timewait ACKs were getting sent
with an incorrect MD5 signature when signatures were enabled.

I broke this in 49a72dfb ("tcp: Fix
MD5 signatures for non-linear skbs"). I didn't take into account that
the skb passed to tcp_*_send_ack was the inbound packet, thus the
source and dest addresses need to be swapped when calculating the MD5
pseudoheader.
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP used ip6_xmit() to send fragments after received ICMP packet too
big message. But while send packet used ip6_xmit, the skb->local_df is
not initialized. So when skb if enter ip6_fragment(), the following
code will discard the skb.

ip6_fragment(...)
{
    if (!skb->local_df) {
        ...
        return -EMSGSIZE;
    }
    ...
}

SCTP do the following step:
1. send packet ip6_xmit(skb, ipfragok=0)
2. received ICMP packet too big message
3. if PMTUD_ENABLE: ip6_xmit(skb, ipfragok=1)

This patch fixed the problem by set local_df if ipfragok is true.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current versions of ipvsadm include "/usr/src/linux/include/net/ip_vs.h"
directly. This file also contains kernel-only definitions. Normally, public
definitions should live in include/linux, so this patch moves the
definitions shared with userspace to a new file, "include/linux/ip_vs.h".

This also removes the unused NFC_IPVS_PROPERTY bitmask, which was once
used to point into skb->nfcache.

To make old ipvsadms still compile with this, the old header file includes
the new one.

Thanks to Dave Miller and Horms for noting/adding the missing Kbuild entry
for the new header file.
Signed-off-by: Julius Volz <juliusv@google.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.

This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.

So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>

Deleting a timer with del_timer doesn't guarantee, that the
timer function is not running at the moment of deletion. Thus
in the xt_hashlimit case we can get into a ticklish situation
when the htable_gc rearms the timer back and we'll actually
delete an entry with a pending timer.

Fix it with using del_timer_sync().

AFAIK del_timer_sync checks for the timer to be pending by
itself, so I remove the check.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The thing is that recent_mt_destroy first flushes the entries
from table with the recent_table_flush and only *after* this
removes the proc file, corresponding to that table.

Thus, if we manage to write to this file the '+XXX' command we
will leak some entries. If we manage to write there a 'clean'
command we'll race in two recent_table_flush flows, since the
recent_mt_destroy calls this outside the recent_lock.

The proper solution as I see it is to remove the proc file first
and then go on with flushing the table. This flushing becomes
safe w/o the lock, since the table is already inaccessible from
the outside.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to time out dead connections quicker, keep track of outstanding data
and cap the timeout.

Suggested by Herbert Xu.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is necessary to set the dongle type on the nsc driver in order to get
it to work correctly.  Thinkpads all appear to use dongle type 9.  This
patch defaults nsc devices with an IBM PnP descriptor to use type 9.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Preface: The "Broadcom" device is on unreleased hardware, so I can't
disclose the actual model.

When the Dell 370 and 410 BT adapters are put into BT radio mode, they
need to be prepared like many other Broadcom adapters.

Also, add quirk Broadcom 2046 devices with HCI_RESET.  Reference for this
bug: https://launchpad.net/bugs/249448Signed-off-by: Michael Frey <michael.frey@canonical.com>
Signed-off-by: Mario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the packed attribute from PofTimStamp_tag in the hysdn driver as the
thing being packed is just an array of chars and so is unpackable.

This deals with a compiler warning:

In file included from drivers/isdn/hysdn/hysdn_boot.c:19:
drivers/isdn/hysdn/hysdn_pof.h:63: warning: 'packed' attribute ignored for field of type 'unsigned char[40]'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix direct casts of pointers to u32 in the InterPhase ATM driver.  These are
all arguments being passed to printk() calls.  So drop the cast and change the
%x to a %p.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix const assignment/discard warnings in the ATM networking driver.

The lane2_assoc_ind() function needed its arguments changing to match changes
in the lane2_ops struct (patch 61c33e01
"atm: use const where reasonable").
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rationale is:
   * use u32 consistently
   * no need to do LCG on values from (better) get_random_bytes
   * use more data from get_random_bytes for secondary seeding
   * don't reduce state space on srandom32()
   * enforce state variable initialization restrictions

Note: the second paper has a version of random32() with even longer period
and a version of random64() if needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

When bridging interfaces with different MTUs, the bridge correctly chooses
the minimum of the MTUs of the physical devices as the bridges MTU.  But
when a frame is passed which fits through the incoming, but not through
the outgoing interface, a "Fragmentation Needed" packet is generated.

However, the propagated MTU is hardcoded to 1500, which is wrong in this
situation.  The sender will repeat the packet again with the same frame
size, and the same problem will occur again.

Instead of sending 1500, the (correct) MTU value of the bridge is now sent
via PMTU.  To achieve this, the corresponding rtable structure is stored
in its net_bridge structure.

Modified to get rid of fake_net_device as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Trying to build with CONFIG_NE2000=m fails with:

  scripts/mod/modpost   -o /tmp/tmp/linux-2.6.27-rc1/Module.symvers    -S     -s
ERROR: "NS8390_init" [drivers/net/ne.ko] undefined!

This is because the split of 8390 into pausing and non-pausing
versions was incompletely propagated to ne.c. This fixes it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Use a menuconfig directive to make all of networking support one-click
deselectable from the top-level menu.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This call is no longer needed, sockstat6 is per namespace so it is
removed at the namespace subsystem destruction.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From a report by Matti Aarnio, and preliminary patch by Adam Langley.
Signed-off-by: David S. Miller <davem@davemloft.net>