This has been used by me and others for ages, let's stop calling it
experimental.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As none of the callers of bond_update_speed_duplex (need to) check its
return value, there is little point in it returning anything.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include the header to pickup the definitions of the global symbols.

Quiets the following sparse warnings:

warning: symbol 'crush_find_rule' was not declared. Should it be static?
warning: symbol 'crush_do_rule' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Sage Weil <sage@newdream.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the custom DIVA_{INIT,EXIT}_FUNCTION defines and use
the standard __init,__exit markup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quoting Tore Anderson from :
https://bugzilla.kernel.org/show_bug.cgi?id=42572

When RTAX_FEATURE_ALLFRAG is set on a route, the effective TCP segment
size does not take into account the size of the IPv6 Fragmentation
header that needs to be included in outbound packets, causing every
transmitted TCP segment to be fragmented across two IPv6 packets, the
latter of which will only contain 8 bytes of actual payload.

RTAX_FEATURE_ALLFRAG is typically set on a route in response to
receving a ICMPv6 Packet Too Big message indicating a Path MTU of less
than 1280 bytes. 1280 bytes is the minimum IPv6 MTU, however ICMPv6
PTBs with MTU < 1280 are still valid, in particular when an IPv6
packet is sent to an IPv4 destination through a stateless translator.
Any ICMPv4 Need To Fragment packets originated from the IPv4 part of
the path will be translated to ICMPv6 PTB which may then indicate an
MTU of less than 1280.

The Linux kernel refuses to reduce the effective MTU to anything below
1280 bytes, instead it sets it to exactly 1280 bytes, and
RTAX_FEATURE_ALLFRAG is also set. However, the TCP segment size appears
to be set to 1240 bytes (1280 Path MTU - 40 bytes of IPv6 header),
instead of 1232 (additionally taking into account the 8 bytes required
by the IPv6 Fragmentation extension header).

This in turn results in rather inefficient transmission, as every
transmitted TCP segment now is split in two fragments containing
1232+8 bytes of payload.

After this patch, all the outgoing packets that includes a
Fragmentation header all are "atomic" or "non-fragmented" fragments,
i.e., they both have Offset=0 and More Fragments=0.

With help from David S. Miller
Reported-by: Tore Anderson <tore@fud.no>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Tested-by: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-testmode.c

Don't pick __u8/__u16 values directly from raw pointers, but instead use
an array of structures of code:value pairs. This is OK, since the buffer
we take options from is not an skb memory, but a user-to-kernel one.

For those options which don't require any value now, require this to be
zero (for potential future extension of this API).

v2: Changed tcp_repair_opt to use two __u32-s as spotted by David Laight.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same macros is defined in 'include/net/af_ieee802154.h' and is called
IEEE802154_ADDR_LEN. No need another one, so remove it.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate frame allocation routine from data processing function.
This makes code more human readable and easier for understanding.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fragmentation is usefull if multiple devices are connected to an E1
interface. Each fragment will have a subset of the available timeslots.
These devices require a cascde connection or a multiplexer.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

LEDs will show RED if layer 1 is disabled or fails.
LEDs will show GREEN if layer 1 is active.
LEDs will blink if traffic on D-channel.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already have the flag for L1 active, so we should use it.
L2 will be solved in a later patch.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transmitted audio data was interrupted if a bridge was enabled or disabled.
Now transmission seamlessly continues during that action.
Fix in hfcmulti.ko
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

merge TXQ/RXQ/MAC start/enable code to one function as they
are started/enabled at the same time, just like stop/disable them
in the function of atl1c_stop_mac.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used for suspend of S1/S3/S4 and driver remove.
It sets MAC/PHY based on the WoL configuation to get lower power
consumption.
atl1c_phy_power_saving is renamed to atl1c_phy_to_ps_link, this
function is just make PHY enter a link/speed mode to eat less
power.
REG_MAC_CTRL register is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

it's unnecessary to reset/init phy when link down.
Only L1/L2 chip (supported by atlx) need such action.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many magic data are re-configured for PHY during its reset operation
based on chip type to get better compability and stability.
REG_PHY_CTRL register may be configured by BIOS before enter OS.
so, the driver can't directly write to it without any Read-Op.
this change also affect suspend and phy_disable routines.
PHY debug ports and extension registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY polling code for FPGA is considered in every MDIO R/W API.
no need to add additional code to atl1c_open.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bit 17/18 of reg1424 must be clear for l2cb 1.x, or it will cause
the write-reg operation fail without cable connected.
so, please do connect the cable when apply this patch to the driver
to make sure these 2bits are cleared by new driver.
The revised code is move to al1c_reset_mac.
SERDES register definition is refined as well.

when do reset MAC, speed/duplex control right should be transferred
to software before do PHY auto-neg -- by bit MASTER_CTRL_SPEED_MODE_SW.
SERDES register definition is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atl1c_reset_phy follows atl1c_reset_pcie in the whole driver,
so, it's unnecessary to add PHY control code in atl1c_reset_pcie.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy register is read/write via MDIO control module ---
that module will be affected by the hibernate status,
to access phy regs in hib stutus, slow frequency clk must
be selected.
To access phy extension register, the MDIO related
registers are refined/updated, a _core function is
re-wroted for both regular PHY regs and extension regs.
existing PHY r/w function is revised based on the _core.
PHY extension registers will be used for the comming
patches.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

this register is used for l1e(dev=1026)
l1c/l1d/l2cb don't use it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Skip flashing a FW component if that component is not present in a
particular FW UFI image.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCC Response CQEs are processed as part of NAPI poll routine and
also synchronously. If MCC completions are consumed by NAPI poll
routine, wrong status is returned to synchronously waiting routine.
Fix this by getting status of MCC command from command response
instead of response CQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix port num sent in command to get stats. Also skip unnecessary
parsing of stats for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EQ is getting armed wrongly in INTx mode as INTx interrupt is taking
some time to deassert. This can cause another interrupt while NAPI is
scheduled and scheduling a NAPI in interrupt does not take effect.
This causes interrupt to be missed and traffic stalls. Fixing this by
preventing wrong arming of EQ.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lancer does not support DDR self test. Fix ethtool self test by
skipping this test for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase time given by driver to adapter for completing FW download
to 30 seconds. Also return correct status when FW download times out.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN and multicast hardware filters are limited and can get
exhausted in adapters with many PCI functions. If setting
a VLAN or multicast filter fails due to lack of sufficient
hardware resources, these packets get dropped. Fix this by
switching to VLAN or multicast promiscous mode so that these
packets are not dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dsp_spl_jiffies need to be the same datatype as jiffies (which is ulong).
If not, on 64 bit systems it will fallback to schedule the DSP every jiffie
tic as soon jiffies become > 2^32.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If DTMF debug is set and tresh goes under 100, the printk will cause
a division by zero.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases the hardware bridging/conference (2-n parties) was selected,
but still pure software bridging/conference was used.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a bug (was introduced by a cut & paste error)
in cases when dsp->conf was NULL.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

read only, so change it to const.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some kfree_skb() calls should be replaced by consume_skb() to avoid
drop_monitor/dropwatch false positives.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds code to trigger CEE events when an APP change or setall
command is made from user space. This simplifies user space code
significantly by creating a single interface to listen on that
works with both firmware and userland agents.

And if we end up with multiple agents this keeps every thing in
sync userland agents, firmware agents, and kernel notifier consumers.

For an example agent that listens for these events see:

https://github.com/jrfastab/cgdcbxd

cgdcbxd is a daemon used to monitor DCB netlink events and manage
the net_prio control group sub-system.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>