Add support for retrieving port level statistics from device.
Hook is added for ethtool's stats functionality. For example,

$ ethtool -S eth3
NIC statistics:
     rx_packets: 12
     rx_bytes: 2790
     rx_dropped: 0
     rx_errors: 0
     tx_packets: 8
     tx_bytes: 728
     tx_dropped: 0
     tx_errors: 0
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
switchdev offload flags

This patch series introduces new offload flags for switchdev.
Kernel network subsystems can use this flag to accelerate
network functions by offloading to hw.

I expect that there will be need for subsystem specific feature
flag in the future.

This patch series currently only addresses bridge driver link
attribute offloads to hardware.

Looking at the current state of bridge l2 offload in the kernel,
    - flag 'self' is the way to directly manage the bridge device in hw via
      the ndo_bridge_setlink/ndo_bridge_getlink calls

    - flag 'master' is always used to manage the in kernel bridge devices
      via the same ndo_bridge_setlink/ndo_bridge_getlink calls

Today these are used separately. The nic offloads use hwmode "vepa/veb" to go
directly to hw with the "self" flag.

At this point i am trying not to introduce any new user facing flags/attributes.
In the model where we want the kernel bridging to be accelerated with
hardware, we very much want the bridge driver to be involved.

In this proposal,
- The offload flag/bit helps switch asic drivers to indicate that they
  accelerate the kernel networking objects/functions
- The user does not have to specify a new flag to do so. A bridge created with
  switch asic ports will be accelerated if the switch driver supports it.
- The user can continue to directly manage l2 in nics (ixgbe) using the
  existing hwmode/self flags
- It also does not stop users from using the 'self' flag to talk to the
  switch asic driver directly
- Involving the bridge driver makes sure the add/del notifications to user
  space go out after both kernel and hardware are programmed

(To selectively offload bridge port attributes,
example learning in hw only etc, we can introduce offload bits for
per bridge port flag attribute as in my previous patch
https://patchwork.ozlabs.org/patch/413211/. I have not included that in this
series)

v2
   - try a different name for the offload flag/bit
   - tries to solve the stacked netdev case by traversing the lowerdev
     list to reach the switch port

v3 -
    - Tested with bond as bridge port for the stacked device case.
      Includes a bond_fix_features change to not ignore the
      NETIF_F_HW_NETFUNC_OFFLOAD flag
    - Some checkpatch fixes

v4 -
    - rename flag to NETIF_F_HW_SWITCH_OFFLOAD
    - add ndo_bridge_setlink/dellink handlers in bond and team drivers as
      suggested by jiri.
    - introduce default ndo_dflt_netdev_switch_port_bridge_setlink/dellink
    handlers that masters can use to call offload api on lowerdevs.
====================
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>

Currently ndo_bridge_setlink and ndo_bridge_dellink handlers point
to the default switchdev handlers

This follows my bonding driver changes.

I have only compile tested this patch. However similar
bonding code has been tested.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want bond to pick up the offload flag if any of its slaves have it.

NETIF_F_HW_SWITCH_OFFLOAD flag is added to the mask, so that
netdev_increment_features does not ignore it.

This also adds ndo_bridge_setlink and ndo_bridge_dellink handlers.
These currently point to the default handlers provided by the
switchdev api.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets the NETIF_F_HW_SWITCH_OFFLOAD feature flag on rocker ports
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to set/del bridge port attributes in hardware from
the bridge driver.

With this, when the user sends a bridge setlink message with no flags or
master flags set,
   - the bridge driver ndo_bridge_setlink handler sets settings in the kernel
   - calls the swicthdev api to propagate the attrs to the switchdev
	hardware

   You can still use the self flag to go to the switch hw or switch port
   driver directly.

With this, it also makes sure a notification goes out only after the
attributes are set both in the kernel and hw.

The patch calls switchdev api only if BRIDGE_FLAGS_SELF is not set.
This is because the offload cases with BRIDGE_FLAGS_SELF are handled in
the caller (in rtnetlink.c).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port

(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).

The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers

This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a high level feature flag for all switch asic offloads

switch drivers set this flag on switch ports. Logical devices like
bridge, bonds, vxlans can inherit this flag from their slaves/ports.

The patch also adds the flag to NETIF_F_ONE_FOR_ALL, so that it gets
propagated to the upperdevices (bridges and bonds).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- In tx_hard_error_bump_tc interrupt, tc should be bumped only when current
device instance is in DMA threshold mode. Check per device xstats.threshold
other than global tc.

- Set per device xstats.threshold to SF_DMA_MODE when current device
instance is set to SF mode.

v2-changes:
- fix ident style
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit dc9daab2 ("cxgb4: Added support in debugfs to dump
sge_qinfo") a preprocessor check for CONFIG_CXGB4_DCB got added, which should
have been CONFIG_CHELSIO_T4_DCB. After adding the right preprocessor, build
fails due to missing function ethqset2pinfo. Fixing that as well.

V2: Updated description since the patch also fixes build failure
Reported-by: Paul Bolle <pebolle@tiscal.nl>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Olivier Sobrie says:

====================
hso: fix some problems in the disconnect path

These patches attempt to fix some problems I observed when the hso
device is disconnected.
Several patches of this serie are fixing crashes or memleaks when a
hso device is disconnected.
This serie of patches is based on v3.18.

changes in v2:
 - Last patch of the serie dropped since another patch fix the issue.
   See http://marc.info/?l=linux-usb&m=142186699418489 for more info.

 - Added an extra patch avoiding name conflicts for the rfkill interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

By using only the usb interface number for the rfkill name, we might
have a name conflicts in case two similar hso devices are connected.

In this patch, the name of the hso rfkill interface embed the value
of a counter that is incremented each time a new rfkill interface is
added.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.

 - hso_disconnect() is called for usb interface "x". Because the serial
   port was open and because the cleanup method of the tty_port hasn't
   been called yet, hso_serial_ref_free() is not run.
 - hso_probe() is called and fails for a new hso serial usb interface
   "y". The function hso_free_interface() is called and iterates
   over the element of serial_table to find the device associated to
   the usb interface context.
   If the usb interface context of usb interface "y" has been created
   at the same place as for usb interface "x", then the cleanup
   functions are called for usb interfaces "x" and "y" and
   hso_serial_ref_free() is called for both interfaces.
 - release_tty() is called for serial port linked to usb interface "x"
   and possibly crash because the tty_port structure contained in the
   hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.

Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G        W      3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply remove the useless extra tab.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.

To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.

For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.

In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of nr_cpu_ids and use modern percpu allocation.

Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NetCP on Keystone has cpsw ale function similar to other TI SoCs
and this driver is re-used. To allow both ti cpsw and keystone netcp
to re-use the driver, convert the cpsw ale to a module and configure
it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically
linked to both TI CPSW and NetCP and this causes issues when the above
drivers are built as dynamic modules. This patch addresses this issue

While at it, fix the Makefile and code to build both netcp_core and
netcp_ethss as dynamic modules. This is needed to support arm allmodconfig.
This also requires exporting of API calls provided by netcp_core so that
both the above can be dynamic modules.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current behavior only passes RTTs from sequentially acked data to CC.

If sender gets a combined ACK for segment 1 and SACK for segment 3, then the
computed RTT for CC is the time between sending segment 1 and receiving SACK
for segment 3.

Pass the minimum computed RTT from any acked data to CC, i.e. time between
sending segment 3 and receiving SACK for segment 3.
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is only an API consolidation and should make things more readable
it replaces  var * HZ / 1000  constructs by  msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the selftest on the resizable hash table to be built modular, just
like all other tests that do not depend on DEBUG_KERNEL.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Lindgren says:

====================
Changes to cpsw and davinci_emac for getting MAC address

Here are a few patches to add common code for cpsw and davinci_emac for
getting the MAC address. Looks like we can also now add code to get the
MAC address on 3517 but in a slightly different way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.

Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.

Let's also use ether_addr_copy() for davinci_emac while at it.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.

At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-3.20-20150128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2015-28-01

this is a pull request of 12 patches for net-next/master.

There are 3 patches by Ahmed S. Darwish, which update the kvaser_usb
driver and add support for the USBcan-II based adapters. Stéphane
Grosjean contributes 7 patches for the peak_usb driver, which add
support for the CANFD USB adapters. I contribute 2 patches which clean
up the peak_usb driver structure a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cd1e6504 ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.

The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).

Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).

Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TIME_WAIT sockets are not owning any skb.

ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.

We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.

Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.

This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sock_iocb structure is allocate on stack for each read/write-like
operation on sockets, and contains various fields of which only the
embedded msghdr and sometimes a pointer to the scm_cookie is ever used.
Get rid of the sock_iocb and put a msghdr directly on the stack and pass
the scm_cookie explicitly to netlink_mmap_sendmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>