The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These drivers share one header file, but nothing else.  Worse, both
drivers use the rtl8225 part with different register settings.  The
results has been some ugly naming -- let's simplify that.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>

create_workqueue is deprecated.  The workqueue usage does not seem to
demand any special treatment, so do not set any flags either.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Tejun Heo <tj@kernel.org>

Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A previous conversion from semaphoreto mutexes missed the fact that one
of the semaphores was used in interrupt code. Fixed by changing to
a spinlock.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>

The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4.  If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).

The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft.  See
section 7.1.3.6.3 in current draft (8.0).

Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats.  But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Export the information which antennas are available for configuration as TX or
RX antennas via nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME.  Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative.  Also in the same patch, allow userspace to add
information elements to mesh beacons.  This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old survey implementation was broken and returned nonsense data.

Clear cycle counters and survey data on reset. Since the cycle counters easily
overflow it's better to keep a local version of collected survey data (in ms
resolution, instead of clockrate) and update this every time survey is
retrieved. If survey is retrieved often enough to avoid cycle counter overflows
this works fine, otherwise we could update survey more often, like ath9k does.
Still only the survey for the current channel is kept.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After merge of the rtl8192ce driver, a powerpc build fails with:

drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_init_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: error: implicit declaration of function 'vmalloc'
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: warning: cast to pointer from integer of different size
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_deinit_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:91: error: implicit declaration of function 'vfree'

The problem is fixed by explicitly including the appropriate header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The reg_notifier() was recently updated as being capable of
having the request passed as NULL, fix ath to follow this API
change. Without this we end up oopsing:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath]
PGD b4c4c067 PUD b4c4d067 PMD 0
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:00/0000:00:1b.0/uevent
CPU 1
Modules linked in: <etc>
Pid: 436, comm: modprobe Not tainted 2.6.37-rc5-wl+ #36 6460DWU/6460DWU
RIP: 0010:[<ffffffffa02fb8cb>]  [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath]
RSP: 0018:ffff8800b6f6baa8  EFLAGS: 00010246
RAX: ffff8800b527b254 RBX: ffff8800b532c180 RCX: 0000000000000018
RDX: ffff8800b530c108 RSI: 0000000000000000 RDI: ffff8800b532c180
RBP: ffff8800b6f6baa8 R08: ffff8800b532f268 R09: 0000000000000235
R10: 00000000000016ad R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000016 R14: ffff8800b532f268 R15: 0000000000000011
FS:  00007f0c53104700(0000) GS:ffff8800bed00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000004 CR3: 00000000b6531000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 436, threadinfo ffff8800b6f6a000, task ffff8800b404dc40)
Stack:
 ffff8800b6f6bac8 ffffffffa03ea651 ffff8800b532c180 ffff8800b527b254
 ffff8800b6f6bb38 ffffffffa01835ca ffffffffa019ed00 00000000a019ed80
 0000000000000002 ffff880000000002 ffffffffa0366140 0000000010aee572
Call Trace:
 [<ffffffffa03ea651>] ath9k_reg_notifier+0x41/0x50 [ath9k]
 [<ffffffffa01835ca>] wiphy_update_regulatory+0x4ba/0x5a0 [cfg80211]
 [<ffffffffa0366140>] ? ieee80211_register_hw+0xa0/0x5b0 [mac80211]
 [<ffffffffa0366140>] ? ieee80211_register_hw+0xa0/0x5b0 [mac80211]
 [<ffffffffa017f994>] wiphy_register+0x1d4/0x360 [cfg80211]
 [<ffffffff8114b918>] ? __kmalloc+0x108/0x1c0
 [<ffffffffa0366223>] ieee80211_register_hw+0x183/0x5b0 [mac80211]
 [<ffffffffa03eb49b>] ath9k_init_device+0x66b/0x850 [ath9k]
 [<ffffffffa03f9dd6>] ath_pci_probe+0x2f6/0x3c0 [ath9k]
 [<ffffffff81037529>] ? default_spin_lock_flags+0x9/0x10
 [<ffffffff812e19cf>] local_pci_probe+0x5f/0xd0
 [<ffffffff812e2bf1>] pci_device_probe+0x101/0x120
 [<ffffffff81390aca>] ? driver_sysfs_add+0x7a/0xb0
 [<ffffffff81390c26>] driver_probe_device+0x96/0x1c0
 [<ffffffff81390deb>] __driver_attach+0x9b/0xa0
 [<ffffffff81390d50>] ? __driver_attach+0x0/0xa0
 [<ffffffff81390008>] bus_for_each_dev+0x68/0x90
 [<ffffffff81390a4e>] driver_attach+0x1e/0x20
 [<ffffffff81390309>] bus_add_driver+0xe9/0x290
 [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k]
 [<ffffffff81391130>] driver_register+0x80/0x150
 [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k]
 [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k]
 [<ffffffff812e2e76>] __pci_register_driver+0x56/0xd0
 [<ffffffffa03f9ec3>] ath_pci_init+0x23/0x30 [ath9k]
 [<ffffffffa040702b>] ath9k_init+0x2b/0x4d [ath9k]
 [<ffffffff81002053>] do_one_initcall+0x43/0x190
 [<ffffffff8109fb5b>] sys_init_module+0xbb/0x200
 [<ffffffff8100c042>] system_call_fastpath+0x16/0x1b
Code: <who even reads this anyway? haha, ok you do>
RIP  [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath]
 RSP <ffff8800b6f6baa8>
CR2: 0000000000000004
---[ end trace 6d03d3c7eda9f06b ]---
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Once we moved the core regulatory request to the queue and let
the scheduler process it last_request will have been left NULL
until the schedular decides to process the first request. When
this happens and we are loading a driver with a custom regulatory
request like all Atheros drivers we end up with a NULL pointer
dereference. We fix this by checking if the request was a
custom one.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
PGD 71f91067 PUD 712b2067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/firmware/2-1/loading
CPU 0
Modules linked in: ath9k_htc(+) ath9k_common ath9k_hw ath <etc>
Pid: 3094, comm: insmod Tainted: G        W   2.6.37-rc5-wl #16 INVALID/28427ZQ
RIP: 0010:[<ffffffffa016de87>]  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
RSP: 0018:ffff88007045db78  EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffffa047d9a0 RCX: ffff88007045dbd0
RDX: 0000000000004e20 RSI: 000000000024cde0 RDI: ffff8800700483e0
RBP: ffff88007045db98 R08: ffffffffa02f5b40 R09: 0000000000000001
R10: 000000000000000e R11: 0000000000000001 R12: 0000000000000000
R13: ffff88007004e3b0 R14: 0000000000000000 R15: ffff880070048340
FS:  00007f635a707700(0000) GS:ffff880077400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000004 CR3: 00000000708a9000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process insmod (pid: 3094, threadinfo ffff88007045c000, task ffff8800713e3ec0)
Stack:
 ffffffffa047d9a0 0000000000000000 ffff88007004e3b0 0000000000000000
 ffff88007045dc08 ffffffffa016e147 000000007045dc08 0000000000000002
 ffff8800700483e0 ffffffffa02f5b40 ffff88007045dbd8 0000000000000000
Call Trace:
 [<ffffffffa016e147>] wiphy_apply_custom_regulatory+0x137/0x1d0 [cfg80211]
 [<ffffffffa047a690>] ? ath9k_reg_notifier+0x0/0x50 [ath9k_htc]
 [<ffffffffa02f47f7>] ath_regd_init+0x347/0x430 [ath]
 [<ffffffffa047b1f5>] ath9k_htc_probe_device+0x6c5/0x960 [ath9k_htc]
 [<ffffffffa0472a2c>] ath9k_htc_hw_init+0xc/0x30 [ath9k_htc]
 [<ffffffffa04747e6>] ath9k_hif_usb_probe+0x216/0x3b0 [ath9k_htc]
 [<ffffffffa03bb6bc>] usb_probe_interface+0x10c/0x210 [usbcore]
 [<ffffffff812aec26>] driver_probe_device+0x96/0x1c0
 [<ffffffff812aedf3>] __driver_attach+0xa3/0xb0
 [<ffffffff812aed50>] ? __driver_attach+0x0/0xb0
 [<ffffffff812adaae>] bus_for_each_dev+0x5e/0x90
 [<ffffffff812ae8c9>] driver_attach+0x19/0x20
 [<ffffffff812ae438>] bus_add_driver+0x168/0x320
 [<ffffffff812af071>] driver_register+0x71/0x140
 [<ffffffff811fc4a8>] ? __raw_spin_lock_init+0x38/0x70
 [<ffffffffa03ba39c>] usb_register_driver+0xdc/0x190 [usbcore]
 [<ffffffffa03a2000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc]
 [<ffffffffa047499e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc]
 [<ffffffffa03a202b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc]
 [<ffffffff8100212f>] do_one_initcall+0x3f/0x180
 [<ffffffff8109ef5b>] sys_init_module+0xbb/0x200
 [<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b
Code: <etc, who cares>
RIP  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
 RSP <ffff88007045db78>
CR2: 0000000000000004
---[ end trace 79e4193601c8b713 ]---
Reported-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is not needed for AR9003.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.

This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’

dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:

[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
 #ifdef CONFIG_MAC80211_DEBUGFS
       struct dentry *rs_sta_dbgfs_scale_table_file;
       struct dentry *rs_sta_dbgfs_stats_table_file;
       struct dentry *rs_sta_dbgfs_rate_scale_data_file;
       struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
       u32 dbg_fixed_rate;
 #endif

The issue was introduced by commit a1da077b:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use "__packed" instead of "__attribute__ ((packed))"...
Signed-off-by: John W. Linville <linville@tuxdriver.com>