We don't want to modify all source files the day the FSF moves.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Record the value returned by subdevs from s_stream(0) and handle stop
failures when an error occurs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The field order must match between the source and sink pads, or the sink
pad field order must be NONE. This allows connecting an interlaced
source to a bridge that has no hardware support for interlaced formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Enrico Butera <ebutera@users.sourceforge.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the V4L2_CID_TEST_PATTERN control. When the solid colour
mode is selected, additional controls become available for setting the
solid four solid colour components.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add numeric definitions for menu items used in the smiapp driver's test
pattern menu.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

In many cases the test pattern has selectable values for each colour
component. Implement controls for raw bayer components. Additional controls
should be defined for colour components that are not covered by these
controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Now that xc5000_set_params() is also called during resume,
move the code that checks for the firmware to happen there.

This way, the firmware will be loaded either for analog or
digital TV when .resume callback is called.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

When DVB is streaming and suspend is called, it will call
au0828_stop_transport(), with will clean the streaming flag.

Due to that, stop_urb_transfer() will be called twice,
causing an oops.

So, we need another flag to be used at resume, telling it
to restart DVB.

While here, add a logic at stop_urb_transfer() to prevent
it of being called twice, and convert the usb_streaming
flag into boolean.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

dev->dvb is always not null, as it is an area at the dev
memory. So, checking if (dev->dvb) is always true.

Instead of this stupid check, what the code wants to do is
to know if the DVB was successully registered.

Fix it by checking, instead, for dvb->frontend. It should
also be sure that this var will be NULL if the device was
not properly initialized.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

xc5000_set_params() is a bad name for a function that
handles only digital TV. Rename it to xc5000_set_digital_params(),
and proper name the generic function that works for both
digital and analog.

No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

If a device suspends/hibertates with a station tuned, restore
the tuner station at resume.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

As we need a function that reapply the last tuned radio,
in order to do resume, split the code that validates and
updates the internal priv struct from the ones that
actually set radio and TV.

A latter patch will add support for resume.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

As we'll be adding a code to resume tuner operation, we
need to move the code that actually sets DTV on a separate
function, to be called by the resume code.

No functional changes, just code got moved.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

After xc5000 stops working, it waits for 5 seconds, waiting
for a new usage. Only after that it goes to low power mode.

If a suspend event happens before that, a work queue will
remain active, with causes suspend to crash.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

While several tuners have some sort of suspend/resume
implementation, this is currently mangled with an optional
.sleep callback that it is also used to put the device on
low power mode.

Not all drivers implement it, as returning the driver from
low power may require to re-load the firmware, with takes
some time. Also, some drivers may delay it.

So, the more coherent is to add two new optional callbacks
that will let the tuners to directy implement suspend and
resume callbacks if they need.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Suspend/resume conditions can be very tricky. Add some info
printk's to help tracking what's happening there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Instead of using printk(KERN_foo, use pr_foo() macros.

No functional changes.

Note: we should do the same for dprintk(), but that would
require to remove the dprintk levels. So, for now, let's
not touch on it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

No timers should be enabled during suspend. So,
stop them. At resume time, we should do the proper
initialization for it to keep working.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The STREAM_ON state is used by s_format callback,
but the driver never sets it.

Fix it. This will also be needed in order to handle
suspend/resume ops.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The scheduled work should be cancelled during suspend.

At resume time, we need to set the frontend again. So,
add such logic to the driver.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

At resume, we should restore the register contents. So,
reenable the bridge and GPIO settings.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Trying to make au0828 to suspend can do very bad things, as
the polling Kthread is not handled. We should disable it
during suspend, only re-enabling it at resume.

Still, analog and digital TV won't work, as we don't reinit
the settings at resume, but at least it won't hang.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Remove CONFIG_VIDEO_AU0828_RC scope around au0828_rc_register()
and au0828_rc_unregister() calls in au0828-core
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Define au0828_rc_*() stubs to avoid compile errors when
VIDEO_AU0828_RC is disabled and avoid the need to enclose
au0828_rc_*() in ifdef CONFIG_VIDEO_AU0828_RC in .c files.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It doesn't make sense to handle an IR code given before
suspending after the device resume. So, turn off IR
int while suspending.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

As the RC kthread can re-enable IR int, we should first
cancel the kthread and then disable IR int.

While here, remove a temporary debug printk.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.

Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

HVR-850 also has a remote. Enable it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The IR code increases the power consumption of the device.
Allow to disable it via modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Linux 3.17-rc1

Pull x86 platform driver updates from Matthew Garrett:
 "A moderate number of changes, but nothing awfully significant.

  A lot of const cleanups, some reworking and additions to the rfkill
  quirks in the asus driver, a new driver for generating falling laptop
  events on Toshibas and some misc fixes.

  Maybe vendors have stopped inventing things"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
  platform/x86: Enable build support for toshiba_haps
  Documentation: Add file about toshiba_haps module
  platform/x86: Toshiba HDD Active Protection Sensor
  asus-nb-wmi: Add wapf4 quirk for the U32U
  alienware-wmi: make hdmi_mux enabled on case-by-case basis
  ideapad-laptop: Constify DMI table and other r/o variables
  asus-nb-wmi.c: Rename x401u quirk to wapf4
  compal-laptop: correct invalid hwmon name
  toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
  toshiba_acpi: Add extra check to backlight code
  Fix log message about future removal of interface
  ideapad-laptop: Disable touchpad interface on Yoga models
  asus-nb-wmi: Add wapf4 quirk for the X550CC
  intel_ips: Make ips_mcp_limits variables static
  thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
  fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
  hp-wmi: Add missing __init annotations to initialization code
  hp_accel: Constify ACPI and DMI tables
  fujitsu-tablet: Mark DMI callbacks as __init code
  dell-laptop: Mark dell_quirks[] DMI table as __initconst
  ...

Pull idle update from Len Brown:
 "Two Intel-platform-specific updates to intel_idle, and a cosmetic
  tweak to the turbostat utility"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: tweak whitespace in output format
  intel_idle: Broadwell support
  intel_idle: Disable Baytrail Core and Module C6 auto-demotion

Pull module fix from Rusty Russell:
 "Nasty potential bug if someone uses a known module param with an
  invalid value (we don't fail unknown module params any more, just
  warn)"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  module: Clean up ro/nx after early module load failures

Pull virtio-rng update from Amit Shah:
 "Add derating factor for use by hwrng core

  Sending directly to you with the commit log changes Ted Ts'o pointed
  out.  Not sure if Rusty's back after his travel, but this already has
  his s-o-b"

* 'rng-queue' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio:
  virtio: rng: add derating factor for use by hwrng core

Pull btrfs updates from Chris Mason:
 "These are all fixes I'd like to get out to a broader audience.

  The biggest of the bunch is Mark's quota fix, which is also in the
  SUSE kernel, and makes our subvolume quotas dramatically more
  accurate.

  I've been running xfstests with these against your current git
  overnight, but I'm queueing up longer tests as well"

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: disable strict file flushes for renames and truncates
  Btrfs: fix csum tree corruption, duplicate and outdated checksums
  Btrfs: Fix memory corruption by ulist_add_merge() on 32bit arch
  Btrfs: fix compressed write corruption on enospc
  btrfs: correctly handle return from ulist_add
  btrfs: qgroup: account shared subtrees during snapshot delete
  Btrfs: read lock extent buffer while walking backrefs
  Btrfs: __btrfs_mod_ref should always use no_quota
  btrfs: adjust statfs calculations according to raid profiles

Pull file locking bugfixes from Jeff Layton:
 "Most of these patches are to fix a long-standing regression that crept
  in when the BKL was removed from the file-locking code.  The code was
  converted to use a conventional spinlock, but some fl_release_private
  ops can block and you can end up sleeping inside the lock.

  There's also a patch to make /proc/locks show delegations as 'DELEG'"

* tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux:
  locks: update Locking documentation to clarify fl_release_private behavior
  locks: move locks_free_lock calls in do_fcntl_add_lease outside spinlock
  locks: defer freeing locks in locks_delete_lock until after i_lock has been dropped
  locks: don't reuse file_lock in __posix_lock_file
  locks: don't call locks_release_private from locks_copy_lock
  locks: show delegations as "DELEG" in /proc/locks

Pull aio updates from Ben LaHaise.

* git://git.kvack.org/~bcrl/aio-next:
  aio: use iovec array rather than the single one
  aio: fix some comments
  aio: use the macro rather than the inline magic number
  aio: remove the needless registration of ring file's private_data
  aio: remove no longer needed preempt_disable()
  aio: kill the misleading rcu read locks in ioctx_add_table() and kill_ioctx()
  aio: change exit_aio() to load mm->ioctx_table once and avoid rcu_read_lock()