- 04 Sep, 2019 40 commits
-
-
Chunyan Zhang authored
When calling sprd_console_setup(), sprd_uart_port probably is NULL, we should check that first instead of checking its items directly. Also we should check membase to avoid accessing uart device before its initialization finished. Signed-off-by:
Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by:
Chunyan Zhang <zhang.lyra@gmail.com> Reviewed-by:
Baolin Wang <baolin.wang@linaro.org> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Genoud authored
Since commit 18dfef9c ("serial: atmel: convert to irq handling provided mctrl-gpio"), the GPIOs interrupts are handled by mctrl_gpio_irq_handle(). So, atmel_get_lines_status() can be completely killed and replaced by : atmel_uart_readl(port, ATMEL_US_CSR); Suggested-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by:
Richard Genoud <richard.genoud@gmail.com> Link: https://lore.kernel.org/r/20190826071752.30396-1-richard.genoud@gmail.comSigned-off-by:
-
Sergey Organov authored
This should help to avoid unnecessary gaps in transmission while adding little overhead due to low default Tx threshold level (2 bytes). Signed-off-by:
Sergey Organov <sorganov@gmail.com> Link: https://lore.kernel.org/r/1567017475-11919-6-git-send-email-sorganov@gmail.comSigned-off-by:
-
Sergey Organov authored
imx_set_termios(): avoid writing baud rate divider registers when the values to be written are the same as current. Any writing seems to restart transmission/receiving logic in the hardware, that leads to data breakage even when rate doesn't in fact change. E.g., user switches RTS/CTS handshake and suddenly gets broken bytes. Signed-off-by:
-
Sergey Organov authored
imx_set_termios(): disabling individual interrupt requests in UART for duration of the routine is pointless. Get rid of it. Signed-off-by:
-
Sergey Organov authored
imx_set_termios(): stopping receiver and transmitter does harm when something that doesn't touch transmission format/rate changes, such as RTS/CTS handshake. OTOH, it does no good on baud rate or format change, as synchronization on upper-level protocols is still required to do it right. Therefore, just stop doing it. Signed-off-by:
-
Sergey Organov authored
imx_set_termios(): remove busy-waiting "drain Tx FIFO" loop. Worse yet, it was potentially unbounded wait due to RTS/CTS (hardware) handshake. Let user space ensure draining is done before termios change, if draining is needed in the first place. Signed-off-by:
-
Jan Kundrát authored
A recent change split the insertion loop into two parts. The first part accessed bytes 0, 1, ... (rxlen - 2), and the second part by mistake took offset `rxlen` instead of the correct `rxlen - 1`. So one byte was not stored, and the final access wrote past the end of the rx_buf. Fixes: 9c12d739 (tty: max310x: Split uart characters insertion loop) Signed-off-by:
Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by:
Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/13ea227620aaad8a7231d42ed03a8508297d4eb3.1567027079.git.jan.kundrat@cesnet.czSigned-off-by:
-
Wei Yongjun authored
spinlock can be initialized automatically with DEFINE_SPINLOCK() rather than explicitly calling spin_lock_init(). Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20190827114614.102037-1-weiyongjun1@huawei.comSigned-off-by:
-
Ralf Ramsauer authored
There may be setups, where legacy interrupts are not available. This is the caese, e.g., when Linux runs as guest (aka. non-root cell) of the partitioning hypervisor Jailhouse. There, only MSI(-X) interrupts are available for guests. But the 8250_pci driver currently only supports legacy ints. So let's enable MSI(-X) interrupts. Nevertheless, this needs to handled with care: while many 8250 devices actually claim to support MSI(-X) interrupts it should not be enabled be default. I had at least one device in my hands with broken MSI implementation. So better introduce a whitelist with devices that are known to support MSI(-X) interrupts. I tested all devices mentioned in the patch. Signed-off-by:
Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de> Link: https://lore.kernel.org/r/20190812112152.693622-1-ralf.ramsauer@oth-regensburg.deSigned-off-by:
-
Ji-Ze Hong (Peter Hong) authored
Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is only support IO. Signed-off-by:
Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Link: https://lore.kernel.org/r/1565933249-23076-1-git-send-email-hpeter+linux_kernel@gmail.comSigned-off-by:
-
Andy Shevchenko authored
Description of the modem line control GPIOs contain a boolean type to set direction of the line. Since GPIO library provides an enumerator type of flags, we may utilize it and allow a bit more flexibility on the choice of the type of the line parameters. It also removes an additional layer of value conversion. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Stefan Roese <sr@denx.de> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20190814140759.17486-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Mao Wenan authored
When CONFIG_SERIAL_FSL_LINFLEXUART=y and CONFIG_PRINTK is not set, one compilation error is found as below: drivers/tty/serial/fsl_linflexuart.c: In function linflex_earlycon_putchar: drivers/tty/serial/fsl_linflexuart.c:608:31: error: CONFIG_LOG_BUF_SHIFT undeclared (first use in this function); did you mean CONFIG_ISA_BUS_API? if (earlycon_buf.len >= 1 << CONFIG_LOG_BUF_SHIFT) ^~~~~~~~~~~~~~~~~~~~ CONFIG_ISA_BUS_API This because CONFIG_LOG_BUF_SHIFT is depended on CONFIG_PRINTK, fix this by adding dependence for CONFIG_SERIAL_FSL_LINFLEXUART. Fixes: b953815b819b ("tty: serial: Add linflexuart driver for S32V234") Signed-off-by:Mao Wenan <maowenan@huawei.com> Link: https://lore.kernel.org/r/20190820124015.28409-1-maowenan@huawei.comSigned-off-by:
-
Martin Hundebøll authored
Guessing the first tty for a gsm0710 multiplexed serial device is not currently possible, which makes it racy to use with multiple modems. Add a way to map the physical serial tty to its related mux devices using an ioctl. Signed-off-by:
Martin Hundebøll <martin@geanix.com> Link: https://lore.kernel.org/r/20190812211243.98686-1-martin@geanix.comSigned-off-by:
-
Kai-Heng Feng authored
Moxa serial boards only need a special setup function, we can use generic 8250 framework for other parts. So let's merge 8250_moxa to 8250_pci. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20190816165124.16942-1-kai.heng.feng@canonical.comSigned-off-by:
-
Baolin Wang authored
Add loopback function support for Spreadtrum serial controller. Signed-off-by:
-
Geert Uytterhoeven authored
Since commit 1d267ea6 ("serial: mctrl-gpio: simplify init routine"), mctrl_gpio_init() returns failure if the assignment to any member of the gpio array results in an error pointer. Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the !CONFIG_GPIOLIB case. Hence there is no longer a need to check for mctrl_gpio_to_gpiod() returning an error value. A simple NULL check is sufficient. This follows the spirit of commit 445df7ff ("serial: mctrl-gpio: drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core. Signed-off-by:
-
Geert Uytterhoeven authored
Since commit 1d267ea6 ("serial: mctrl-gpio: simplify init routine"), mctrl_gpio_init() returns failure if the assignment to any member of the gpio array results in an error pointer. Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the !CONFIG_GPIOLIB case. Hence there is no longer a need to check for mctrl_gpio_to_gpiod() returning an error value. A simple NULL check is sufficient. This follows the spirit of commit 445df7ff ("serial: mctrl-gpio: drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core. Signed-off-by:
-
Ahung Cheng authored
The IER and DLH registers occupy the same address space, selected by the LCR.DLAB bit. Hence, add port lock to protect IER when LCR.DLAB bit is set. Signed-off-by:
Ahung Cheng <ahcheng@nvidia.com> Signed-off-by:
Krishna Yarlagadda <kyarlagadda@nvidia.com> Acked-by:
Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/1565609303-27000-5-git-send-email-kyarlagadda@nvidia.comSigned-off-by:
-
Andreas Abel authored
Add the internal loopback functionality that can be enabled with TIOCM_LOOP. Signed-off-by:
Andreas Abel <aabel@nvidia.com> Signed-off-by:
-
Razvan Stefanescu authored
When half-duplex RS485 communication is used, after RX is started, TX tasklet still needs to be scheduled tasklet. This avoids console freezing when more data is to be transmitted, if the serial communication is not closed. Fixes: 69646d7a ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped") Signed-off-by:
Razvan Stefanescu <razvan.stefanescu@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190813074025.16218-1-razvan.stefanescu@microchip.comSigned-off-by:
-
Stefan-gabriel Mirea authored
Introduce support for LINFlex driver, based on: - the version of Freescale LPUART driver after commit b3e3bf2e ("Merge 4.0-rc7 into tty-next"); - commit abf1e0a9 ("tty: serial: fsl_lpuart: lock port on console write"). In this basic version, the driver can be tested using initramfs and relies on the clocks and pin muxing set up by U-Boot. Remarks concerning the earlycon support: - LinFlexD does not allow character transmissions in the INIT mode (see section 47.4.2.1 in the reference manual[1]). Therefore, a mutual exclusion between the first linflex_setup_watermark/linflex_set_termios executions and linflex_earlycon_putchar was employed and the characters normally sent to earlycon during initialization are kept in a buffer and sent afterwards. - Empirically, character transmission is also forbidden within the last 1-2 ms before entering the INIT mode, so we use an explicit timeout (PREINIT_DELAY) between linflex_earlycon_putchar and the first call to linflex_setup_watermark. - U-Boot currently uses the UART FIFO mode, while this driver makes the transition to the buffer mode. Therefore, the earlycon putchar function matches the U-Boot behavior before initializations and the Linux behavior after. [1] https://www.nxp.com/webapp/Download?colCode=S32V234RMSigned-off-by:
Stoica Cosmin-Stefan <cosmin.stoica@nxp.com> Signed-off-by:
Adrian.Nitu <adrian.nitu@freescale.com> Signed-off-by:
Larisa Grigore <Larisa.Grigore@nxp.com> Signed-off-by:
Ana Nedelcu <B56683@freescale.com> Signed-off-by:
Mihaela Martinas <Mihaela.Martinas@freescale.com> Signed-off-by:
Matthew Nunez <matthew.nunez@nxp.com> [stefan-gabriel.mirea@nxp.com: Reduced for upstreaming and implemented earlycon support] Signed-off-by:
Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com> Link: https://lore.kernel.org/r/20190809112853.15846-6-stefan-gabriel.mirea@nxp.comSigned-off-by:
-
Colin Ian King authored
Variable ret is initialized to a value that is never read and it is re-assigned later. The initialization is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20190809174042.6276-1-colin.king@canonical.comSigned-off-by:
-
Kai-Heng Feng authored
Sunix Multi I/O boards are different to Timedia's. This patch adds proper support for Sunix MIO boards with 1 parallel and up to 4 serial ports. Cc: Morris Ku <morris_ku@sunix.com> Cc: Debbie Liu <debbie_liu@sunix.com> Signed-off-by:
-
Kai-Heng Feng authored
Add support to Sunix serial boards with up to 16 ports. Sunix board need its own setup callback instead of using Timedia's, to properly support more than 4 ports. Cc: Morris Ku <morris_ku@sunix.com> Cc: Debbie Liu <debbie_liu@sunix.com> Signed-off-by:
-
Arnd Bergmann authored
The platform is getting removed, so there are no more users of this driver. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190809202749.742267-3-arnd@arndb.deSigned-off-by:
-
Rahul Tanwar authored
This patch adds IRQ & ISR support in the driver for Lightning Mountain SoC. Signed-off-by:
Rahul Tanwar <rahul.tanwar@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@intel.com> Link: https://lore.kernel.org/r/0df20f6e4bbf9de09c85a5c92c92e642f62f441f.1565257887.git.rahul.tanwar@linux.intel.comSigned-off-by:
-
Rahul Tanwar authored
This driver/IP is reused across multiple SoCs. Older SoCs supported three separate IRQs for tx, rx & err interrupts. Newer Lightning Mountain SoC supports single IRQ for all of tx/rx/err interrupts. This patch modifies the driver design to support dynamic assignment of IRQ resources & ISRs based on devicetree node compatible entries. Suggested-by:
-
Rahul Tanwar authored
Use explicit string instead of a macro for devicetree compatible string. This series of patches is to add support for multiple SoCs which reuse the same serial controller IP. The following patches will add another compatible string to support new Lightning Mountain(LGM) SoC. So it makes sense to have the compatible strings explicitly mentioned instead of a fixed macro. Suggested-by:
-
Andy Shevchenko authored
Intel Elkhart Lake may use High Speed UART from OSE IP block. This is different to what we have in main LPSS, though compatible with older version of it, which is handled by this driver. Enable OSE HS UART on Intel Elkhart Lake by adding PCI IDs. Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20190806094322.64987-9-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Andy Shevchenko authored
Since PCI core provides a generic PCI_DEVICE_DATA() macro, replace LPSS_DEVICE() with former one. No functional change intended. Signed-off-by:
-
Andy Shevchenko authored
It is really useful not only for debugging to have an DMA IRQ line and pool being mapped to the corresponding IP by using its instance ID. Provide PCI device and function as instance ID for Intel Quark UART DMA. Signed-off-by:
-
Andy Shevchenko authored
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a valid divisor latch fraction register. Now the preparation is done, it's easy to add the feature support. This patch firstly tries to get the fractional divisor width during probe, then setups specific get_divisor() and set_divisor() hook. Among other changes the FIFO size is now retrieved from the hardware. Signed-off-by:
-
Andy Shevchenko authored
Since we have a common library module for Synopsys DesignWare UART, let us use it. Signed-off-by:
-
Andy Shevchenko authored
Since we have a common library module for Synopsys DesignWare UART, let us use it. Signed-off-by:
-
Andy Shevchenko authored
We would like to use same functions in the couple of drivers for Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand library module which users will select explicitly. Signed-off-by:
-
Andy Shevchenko authored
The use of pointer will simplify enabling runtime PM for the driver. Signed-off-by:
-
Andy Shevchenko authored
The commit 2cb78eab ("serial: 8250_dw: Use a unified new dev variable in probe") introduced a local dev variable in ->probe(). Do the same in ->remove() in order to prepare for sequential patches. Signed-off-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Link: https://lore.kernel.org/r/20190806094322.64987-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Rahul Tanwar authored
The existing driver can only support single core SoC. But new multicore platforms which reuse the same driver/IP need SMP support. This patch adds multicore support in the driver. Signed-off-by:
-
Andrey Smirnov authored
In a mixed DMA/IRQ use-case (e.g.: DMA for TX, IRQ for RX), interrupt handler might try to handle Rx/Tx condition it shouldn't. Change the code to only handle TX/RX event if corresponding path isn't being handled by DMA. Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-7-andrew.smirnov@gmail.comSigned-off-by:
-
