I'm handing over maintainership to Jeff Kirsher and moving on
to other Linux/Open Source work within Intel. Good luck to Jeff ;)
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Periodically check the MII PHY status to ensure that the
network layer's link status is updated and the user informed
of any changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

There was a missing newline in a dev_dbg() message.  Values read
from/written into PHY registers might be for interest too, so I added
new dbg messages there.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

There were missing __dev* annotations for the dm9000_probe()
and dm9000_drv_remove() functions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

noticed while browsing code, apparent thinko.  compile tested only.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add a set of self-tests accessible thorugh ethtool.
Add hardware loopback and TX disable control code to support them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

An RX_RESET event can be reported either as a global or as a driver event.
We were counting only global events.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fall-through is expected outside a switch statement.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The 10Xpress PHY supports flash upgrades through MDIO, but needs to be
put in upgrade mode at power-up.  This adds a module parameter and other
logic to support that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The SFC4000 controller does not have hardware support for TSO, and the
core GSO code incurs a high cost in allocating and freeing skbs.  This
TSO implementation uses lightweight packet header structures and is
substantially faster.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The eHEA driver uses the recently modified walk_memory_resource for powerpc
functionality to detect the memory layout. It further uses the memory hotplug
notifiers to catch memory hotplug events.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The new ehea memory hot plug implementation depends on MEMORY_HOTPLUG.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch introduces two exports to allow modules to use memory notifiers.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The loop that unmaps all of the TX Buffer Descriptors never actually
moves the txbd pointer, so we were just repeatedly unmapping the first one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Reset the chip when the PCI link goes down.
Preserve the napi structure when a sge qset's resources are freed.
Replay only HW initialization when the chip comes out of reset.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fix faiures path when ports are stopped and restarted
in EEH recovery.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fix a long-standing bug/misunderstanding between the
driver and the firmware.  The size of the interrupt
queue must be set to the number of rx slots (big + small),
and it should never have been a tunable.
Setting it too small results in chaos.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add myri10ge_get_firmware_capabilities() to retrieve TSO6 and
interrupt slots capabilities from the firmware.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

To prepare and simplify multislice rx support, add a single slice
structure and move some fields in there.
No functional change yet.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fix another potential for an infinite loop while looking for the
root port in myri10ge_enable_ecrc().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add some blank lines to uniformize the code and match
the upstream code.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add a barrier() in the usleep() loop in  myri10ge_send_cmd().
Without the barrier, some mips machine never notices that the
firmware has DMA'ed the response.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Make ethtool report FIBER for XFP based NIC's port type.
Don't bother to poke around and try to find out what is in
the XFP cage, since Linux does not have separate media types
for -SR -LR, etc.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Properly align scratch buffers when making boot commands.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Increase the handoff timeout to 512ms so as to give the aeluros based
NICs sufficient time to handoff without relying on the msleep() being
sloppy, and accidentally sleeping way longer than the 20ms we specified
in 20 separate 1ms sleeps.

Fix typo in the handoff sleep delay, which made it additive, not
exponential.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Remove useless linebreaks at the end of MODULE_PARM_DESC
and fix the description of myri10ge_lro_max_pkts.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Update myri10ge firmware headers.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

atl1-2.1.3.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add a shutdown callback that points to atl1_suspend().  This, along
with a working suspend function, fixes wake-on-lan.
Tested-by: Per Olofsson <pelle@dsv.su.se>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fix atl1_suspend() and atl1_resume() so they actually work.  We'll use
the suspend function for wake-on-lan in addition to just suspending.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Using vendor-provided magic, add code to enter power save mode
on the PHY.  We'll need this for suspend and wake-on-lan.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the bug that the I/O buffer is not freed at the driver removal.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some APs refuse association if the supported rates contained in the
association request do not match its own supported rates. This patch
introduces a new function which builds the intersection between the AP's
supported rates and the client's supported rates to work around such
problems. The same approach is already used in ipw2200 for example.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug in RX path, the frequency was wrongly set in the
ieee80211_rx_status. This bug led to an empty scan list in A band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>