Fix wrong reading of upper pages for SFP EEPROM. According to "Memory
Organization" figure in SFF-8472 spec: When reading upper pages 1, 2 and
3 the offset should be set relative to zero and I2C high address 0x51
[1010001X (A2h)] is to be used.

Fixes: a45bfb5a ("mlxsw: core: Extend QSFP EEPROM size for ethtool")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.

Fixes: bcf3440c ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch disables PTP on AQC111 and AQC112 due to a known HW issue,
which can cause datapath issues.

Ideally PTP block should have been disabled via PHY provisioning, but
unfortunately many units have been shipped with enabled PTP block.
Thus, we have to work around this in the driver.

Fixes: dbcd6806 ("net: aquantia: add support for Phy access")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When nfc_register_device fails in nci_register_device,
destroy_workqueue() shouled be called to destroy ndev->tx_wq.

Fixes: 3c1c0f5d ("NFC: NCI: Fix nci_register_device init sequence")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Doug Berger says:

====================
net: bcmgenet: fix WAKE_FILTER resume from deep sleep

The WAKE_FILTER logic can only wake the system from the standby
power state. However, some systems that include the GENET IP
support deeper power saving states and the driver should suspend
and resume correctly from those states as well.

This commit set squashes a few issues uncovered while testing
suspend and resume from these deep sleep states.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.

This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.

Fixes: f50932cc ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.

This commit adds a check of the RBUF_ACPI_EN flag when Wake
on Filter is enabled. A clear flag indicates that the GENET
hardware must have been reset so the remainder of the
hardware programming is bypassed.

Fixes: f50932cc ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.

This commit adds a check of the MPD_EN flag when Wake on
Magic Packet is enabled. A clear flag indicates that the
GENET hardware must have been reset so the remainder of the
hardware programming is bypassed.

Fixes: 1a1d5106 ("net: bcmgenet: move clk_wol management to bcmgenet_wol")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix ip_defrag.sh when CONFIG_NF_DEFRAG_IPV6=m:

$ sudo ./ip_defrag.sh
+ set -e
+ mktemp -u XXXXXX
+ readonly NETNS=ns-rGlXcw
+ trap cleanup EXIT
+ setup
+ ip netns add ns-rGlXcw
+ ip -netns ns-rGlXcw link set lo up
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_high_thresh=9000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_low_thresh=7000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_time=1
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_high_thresh=9000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_low_thresh=7000000
+ ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_time=1
+ ip netns exec ns-rGlXcw sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000
+ cleanup
+ ip netns del ns-rGlXcw

$ ls -la /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh
ls: cannot access '/proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh': No such file or directory

$ sudo modprobe nf_defrag_ipv6
$ ls -la /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh
-rw-r--r-- 1 root root 0 Jul 14 12:34 /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If try_toggle_control_gpio() failed in smc_drv_probe(), free_netdev(ndev)
should be called to free the ndev created earlier. Otherwise, a memleak
will occur.

Fixes: 7d2911c4 ("net: smc91x: Fix gpios for device tree based booting")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vlan_newlink call register_vlan_dev fails, it might return error
with dev->reg_state = NETREG_UNREGISTERED. The rtnl_newlink should
free the memory. But currently rtnl_newlink only free the memory which
state is NETREG_UNINITIALIZED.

BUG: memory leak
unreferenced object 0xffff8881051de000 (size 4096):
  comm "syz-executor139", pid 560, jiffies 4294745346 (age 32.445s)
  hex dump (first 32 bytes):
    76 6c 61 6e 32 00 00 00 00 00 00 00 00 00 00 00  vlan2...........
    00 45 28 03 81 88 ff ff 00 00 00 00 00 00 00 00  .E(.............
  backtrace:
    [<0000000047527e31>] kmalloc_node include/linux/slab.h:578 [inline]
    [<0000000047527e31>] kvmalloc_node+0x33/0xd0 mm/util.c:574
    [<000000002b59e3bc>] kvmalloc include/linux/mm.h:753 [inline]
    [<000000002b59e3bc>] kvzalloc include/linux/mm.h:761 [inline]
    [<000000002b59e3bc>] alloc_netdev_mqs+0x83/0xd90 net/core/dev.c:9929
    [<000000006076752a>] rtnl_create_link+0x2c0/0xa20 net/core/rtnetlink.c:3067
    [<00000000572b3be5>] __rtnl_newlink+0xc9c/0x1330 net/core/rtnetlink.c:3329
    [<00000000e84ea553>] rtnl_newlink+0x66/0x90 net/core/rtnetlink.c:3397
    [<0000000052c7c0a9>] rtnetlink_rcv_msg+0x540/0x990 net/core/rtnetlink.c:5460
    [<000000004b5cb379>] netlink_rcv_skb+0x12b/0x3a0 net/netlink/af_netlink.c:2469
    [<00000000c71c20d3>] netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
    [<00000000c71c20d3>] netlink_unicast+0x4c6/0x690 net/netlink/af_netlink.c:1329
    [<00000000cca72fa9>] netlink_sendmsg+0x735/0xcc0 net/netlink/af_netlink.c:1918
    [<000000009221ebf7>] sock_sendmsg_nosec net/socket.c:652 [inline]
    [<000000009221ebf7>] sock_sendmsg+0x109/0x140 net/socket.c:672
    [<000000001c30ffe4>] ____sys_sendmsg+0x5f5/0x780 net/socket.c:2352
    [<00000000b71ca6f3>] ___sys_sendmsg+0x11d/0x1a0 net/socket.c:2406
    [<0000000007297384>] __sys_sendmsg+0xeb/0x1b0 net/socket.c:2439
    [<000000000eb29b11>] do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
    [<000000006839b4d0>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: cb626bf5 ("net-sysfs: Fix reference count leak")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add below to “Ancillary clock features” section
  - Low Pass Filter (LPF) access from user space

Add below to list of “Supported hardware” section
  + Renesas (IDT) ClockMatrix™Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From Documentation/networking/timestamping.txt:

  A driver which supports hardware time stamping shall update the
  struct with the actual, possibly more permissive configuration.

Do update the struct passed when we upscale the requested time
stamping mode.

Fixes: cb646e2b ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix support for external PTP-aware devices such as DSA or PTP PHY:

Make sure we never time stamp tx packets when hardware time stamping
is disabled.

Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.

Fixes: 6605b730 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.

Fixes: a9a51bd7 ("ax88172a: fix information leak on short answers")
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+4cd84f527bf4a10fc9c1@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 0deab087 ("vsock/virtio: use RCU to avoid use-after-free
on the_virtio_vsock") starts to use RCU to protect 'the_virtio_vsock'
pointer, but we forgot to annotate it.

This patch adds the annotation to fix the following sparse errors:

    net/vmw_vsock/virtio_transport.c:73:17: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:73:17:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:73:17:    struct virtio_vsock *
    net/vmw_vsock/virtio_transport.c:171:17: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:171:17:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:171:17:    struct virtio_vsock *
    net/vmw_vsock/virtio_transport.c:207:17: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:207:17:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:207:17:    struct virtio_vsock *
    net/vmw_vsock/virtio_transport.c:561:13: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:561:13:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:561:13:    struct virtio_vsock *
    net/vmw_vsock/virtio_transport.c:612:9: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:612:9:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:612:9:    struct virtio_vsock *
    net/vmw_vsock/virtio_transport.c:631:9: error: incompatible types in comparison expression (different address spaces):
    net/vmw_vsock/virtio_transport.c:631:9:    struct virtio_vsock [noderef] __rcu *
    net/vmw_vsock/virtio_transport.c:631:9:    struct virtio_vsock *

Fixes: 0deab087 ("vsock/virtio: use RCU to avoid use-after-free on the_virtio_vsock")
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The fsl_mc_get_endpoint() function can return an error or directly a
NULL pointer in case the peer device is not under the root DPRC
container. Treat this case also, otherwise it would lead to a NULL
pointer when trying to access the peer fsl_mc_device.

Fixes: 71947923 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During setup():
...
        for ns in h0 r1 h1 h2 h3
        do
                create_ns ${ns}
        done
...

while in cleanup():
...
        for n in h1 r1 h2 h3 h4
        do
                ip netns del ${n} 2>/dev/null
        done
...

and after removing the stderr redirection in cleanup():

$ sudo ./fib_nexthop_multiprefix.sh
...
TEST: IPv4: host 0 to host 3, mtu 1400                              [ OK ]
TEST: IPv6: host 0 to host 3, mtu 1400                              [ OK ]
Cannot remove namespace file "/run/netns/h4": No such file or directory
$ echo $?
1

and a non-zero return code, make kselftests fail (even if the test
itself is fine):

...
not ok 34 selftests: net: fib_nexthop_multiprefix.sh # exit=1
...
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there is no valid MAC address in the device tree,
use a random MAC address.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

The size used when calling 'pci_alloc_consistent()' and
'pci_free_consistent()' should match.

Fix it and have it consistent with the corresponding call in 'rr_close()'.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-2020-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.8

First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.

iwlwifi

* fix sleeping under RCU

* fix a kernel crash when using compressed firmware images

mt76

* tx queueing fixes for mt7615/22/63

* locking fix

* fix a crash during watchdog reset

* fix memory leaks
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

KASAN report null-ptr-deref error when register_netdev() failed:

KASAN: null-ptr-deref in range [0x00000000000003c0-0x00000000000003c7]
CPU: 2 PID: 422 Comm: ip Not tainted 5.8.0-rc4+ #12
Call Trace:
 ip6gre_init_net+0x4ab/0x580
 ? ip6gre_tunnel_uninit+0x3f0/0x3f0
 ops_init+0xa8/0x3c0
 setup_net+0x2de/0x7e0
 ? rcu_read_lock_bh_held+0xb0/0xb0
 ? ops_init+0x3c0/0x3c0
 ? kasan_unpoison_shadow+0x33/0x40
 ? __kasan_kmalloc.constprop.0+0xc2/0xd0
 copy_net_ns+0x27d/0x530
 create_new_namespaces+0x382/0xa30
 unshare_nsproxy_namespaces+0xa1/0x1d0
 ksys_unshare+0x39c/0x780
 ? walk_process_tree+0x2a0/0x2a0
 ? trace_hardirqs_on+0x4a/0x1b0
 ? _raw_spin_unlock_irq+0x1f/0x30
 ? syscall_trace_enter+0x1a7/0x330
 ? do_syscall_64+0x1c/0xa0
 __x64_sys_unshare+0x2d/0x40
 do_syscall_64+0x56/0xa0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

ip6gre_tunnel_uninit() has set 'ign->fb_tunnel_dev' to NULL, later
access to ign->fb_tunnel_dev cause null-ptr-deref. Fix it by saving
'ign->fb_tunnel_dev' to local variable ndev.

Fixes: dafabb65 ("ip6_gre: fix use-after-free in ip6gre_tunnel_lookup()")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":

    drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
    include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
    drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
       hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
       ^~~~~~~
    include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
    drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
       hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
       ^~~~~~~

As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 3 bug fixes.

2 Fixes related to PHY/link settings.  The last one fixes the sizing of
the completion ring.

Please also queue for -stable.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current completion ring sizing formula is wrong with TPA enabled.
The formula assumes that the number of TPA completions are bound by the
RX ring size, but that's not true.  TPA_START completions are immediately
recycled so they are not bound by the RX ring size.  We must add
bp->max_tpa to the worst case maximum RX and TPA completions.

The completion ring can overflow because of this mistake.  This will
cause hardware to disable the completion ring when this happens,
leading to RX and TX traffic to stall on that ring.  This issue is
generally exposed only when the RX ring size is set very small.

Fix the formula by adding bp->max_tpa to the number of RX completions
if TPA is enabled.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.");
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a shared port PHY configuration, async event is received when any of the
port modifies the configuration. Ethtool link settings should be
initialised after updated PHY configuration from firmware.

Fixes: b1613e78 ("bnxt_en: Add async. event logic for PHY configuration changes.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago.  The pause setting was missed when
making that change.  Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().

Fixes: e2dc9b6e ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fix from Dan Williams:
 "A one-line Fix for key ring search permissions to address a regression
  from -rc1"

* tag 'libnvdimm-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm/security: Fix key lookup permissions

Pull cifs fixes from Steve French:
 "Four cifs/smb3 fixes: the three for stable fix problems found recently
  with change notification including a reference count leak"

* tag '5.8-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  cifs: fix reference leak for tlink
  smb3: fix unneeded error message on change notify
  cifs: remove the retry in cifs_poxis_lock_set
  smb3: fix access denied on change notify request to some servers

Pull coding style terminology documentation from Dan Williams:
 "The discussion has tapered off as well as the incoming ack, review,
  and sign-off tags. I did not see a reason to wait for the next merge
  window"

* tag 'inclusive-terminology' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux:
  CodingStyle: Inclusive Terminology

Pull networking fixes from David Miller:

 1) Restore previous behavior of CAP_SYS_ADMIN wrt loading networking
    BPF programs, from Maciej Żenczykowski.

 2) Fix dropped broadcasts in mac80211 code, from Seevalamuthu
    Mariappan.

 3) Slay memory leak in nl80211 bss color attribute parsing code, from
    Luca Coelho.

 4) Get route from skb properly in ip_route_use_hint(), from Miaohe Lin.

 5) Don't allow anything other than ARPHRD_ETHER in llc code, from Eric
    Dumazet.

 6) xsk code dips too deeply into DMA mapping implementation internals.
    Add dma_need_sync and use it. From Christoph Hellwig

 7) Enforce power-of-2 for BPF ringbuf sizes. From Andrii Nakryiko.

 8) Check for disallowed attributes when loading flow dissector BPF
    programs. From Lorenz Bauer.

 9) Correct packet injection to L3 tunnel devices via AF_PACKET, from
    Jason A. Donenfeld.

10) Don't advertise checksum offload on ipa devices that don't support
    it. From Alex Elder.

11) Resolve several issues in TCP MD5 signature support. Missing memory
    barriers, bogus options emitted when using syncookies, and failure
    to allow md5 key changes in established states. All from Eric
    Dumazet.

12) Fix interface leak in hsr code, from Taehee Yoo.

13) VF reset fixes in hns3 driver, from Huazhong Tan.

14) Make loopback work again with ipv6 anycast, from David Ahern.

15) Fix TX starvation under high load in fec driver, from Tobias
    Waldekranz.

16) MLD2 payload lengths not checked properly in bridge multicast code,
    from Linus Lüssing.

17) Packet scheduler code that wants to find the inner protocol
    currently only works for one level of VLAN encapsulation. Allow
    Q-in-Q situations to work properly here, from Toke
    Høiland-Jørgensen.

18) Fix route leak in l2tp, from Xin Long.

19) Resolve conflict between the sk->sk_user_data usage of bpf reuseport
    support and various protocols. From Martin KaFai Lau.

20) Fix socket cgroup v2 reference counting in some situations, from
    Cong Wang.

21) Cure memory leak in mlx5 connection tracking offload support, from
    Eli Britstein.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
  mlxsw: pci: Fix use-after-free in case of failed devlink reload
  mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()
  net: macb: fix call to pm_runtime in the suspend/resume functions
  net: macb: fix macb_suspend() by removing call to netif_carrier_off()
  net: macb: fix macb_get/set_wol() when moving to phylink
  net: macb: mark device wake capable when "magic-packet" property present
  net: macb: fix wakeup test in runtime suspend/resume routines
  bnxt_en: fix NULL dereference in case SR-IOV configuration fails
  libbpf: Fix libbpf hashmap on (I)LP32 architectures
  net/mlx5e: CT: Fix memory leak in cleanup
  net/mlx5e: Fix port buffers cell size value
  net/mlx5e: Fix 50G per lane indication
  net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash
  net/mlx5e: Fix VXLAN configuration restore after function reload
  net/mlx5e: Fix usage of rcu-protected pointer
  net/mxl5e: Verify that rpriv is not NULL
  net/mlx5: E-Switch, Fix vlan or qos setting in legacy mode
  net/mlx5: Fix eeprom support for SFP module
  cgroup: Fix sock_cgroup_data on big-endian.
  selftests: bpf: Fix detach from sockmap tests
  ...

CONFIG_CC_IS_GCC is undefined when Clang is used, which breaks the build
(see our Travis link below).

Clang 8 was chosen as a minimum version for this check because there
were some improvements around __builtin_constant_p in that release. In
reality, MIPS was not even buildable until clang 9 so that check was not
technically necessary. Just remove all compiler checks and just assume
that we have a working compiler.

Fixes: d4e60453 ("Restore gcc check in mips asm/unroll.h")
Link: https://travis-ci.com/github/ClangBuiltLinux/continuous-integration/jobs/359642821Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Ido Schimmel says:

====================
mlxsw: Various fixes

Fix two issues found by syzkaller.

Patch #1 removes inappropriate usage of WARN_ON() following memory
allocation failure. Constantly triggered when syzkaller injects faults.

Patch #2 fixes a use-after-free that can be triggered by 'devlink dev
info' following a failed devlink reload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case devlink reload failed, it is possible to trigger a
use-after-free when querying the kernel for device info via 'devlink dev
info' [1].

This happens because as part of the reload error path the PCI command
interface is de-initialized and its mailboxes are freed. When the
devlink '->info_get()' callback is invoked the device is queried via the
command interface and the freed mailboxes are accessed.

Fix this by initializing the command interface once during probe and not
during every reload.

This is consistent with the other bus used by mlxsw (i.e., 'mlxsw_i2c')
and also allows user space to query the running firmware version (for
example) from the device after a failed reload.

[1]
BUG: KASAN: use-after-free in memcpy include/linux/string.h:406 [inline]
BUG: KASAN: use-after-free in mlxsw_pci_cmd_exec+0x177/0xa60 drivers/net/ethernet/mellanox/mlxsw/pci.c:1675
Write of size 4096 at addr ffff88810ae32000 by task syz-executor.1/2355

CPU: 1 PID: 2355 Comm: syz-executor.1 Not tainted 5.8.0-rc2+ #29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xf6/0x16e lib/dump_stack.c:118
 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383
 __kasan_report mm/kasan/report.c:513 [inline]
 kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
 check_memory_region_inline mm/kasan/generic.c:186 [inline]
 check_memory_region+0x14e/0x1b0 mm/kasan/generic.c:192
 memcpy+0x39/0x60 mm/kasan/common.c:106
 memcpy include/linux/string.h:406 [inline]
 mlxsw_pci_cmd_exec+0x177/0xa60 drivers/net/ethernet/mellanox/mlxsw/pci.c:1675
 mlxsw_cmd_exec+0x249/0x550 drivers/net/ethernet/mellanox/mlxsw/core.c:2335
 mlxsw_cmd_access_reg drivers/net/ethernet/mellanox/mlxsw/cmd.h:859 [inline]
 mlxsw_core_reg_access_cmd drivers/net/ethernet/mellanox/mlxsw/core.c:1938 [inline]
 mlxsw_core_reg_access+0x2f6/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1985
 mlxsw_reg_query drivers/net/ethernet/mellanox/mlxsw/core.c:2000 [inline]
 mlxsw_devlink_info_get+0x17f/0x6e0 drivers/net/ethernet/mellanox/mlxsw/core.c:1090
 devlink_nl_info_fill.constprop.0+0x13c/0x2d0 net/core/devlink.c:4588
 devlink_nl_cmd_info_get_dumpit+0x246/0x460 net/core/devlink.c:4648
 genl_lock_dumpit+0x85/0xc0 net/netlink/genetlink.c:575
 netlink_dump+0x515/0xe50 net/netlink/af_netlink.c:2245
 __netlink_dump_start+0x53d/0x830 net/netlink/af_netlink.c:2353
 genl_family_rcv_msg_dumpit.isra.0+0x296/0x300 net/netlink/genetlink.c:638
 genl_family_rcv_msg net/netlink/genetlink.c:733 [inline]
 genl_rcv_msg+0x78d/0x9d0 net/netlink/genetlink.c:753
 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
 netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg+0x150/0x190 net/socket.c:672
 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
 ___sys_sendmsg+0xff/0x170 net/socket.c:2417
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: a9c8336f ("mlxsw: core: Add support for devlink info command")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not trigger a warning when a memory allocation fails. Remove
the WARN_ON().

The warning is constantly triggered by syzkaller when it is injecting
faults:

[ 2230.758664] FAULT_INJECTION: forcing a failure.
[ 2230.758664] name failslab, interval 1, probability 0, space 0, times 0
[ 2230.762329] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28
...
[ 2230.898175] WARNING: CPU: 3 PID: 1407 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:6265 mlxsw_sp_router_fib_event+0xfad/0x13e0
[ 2230.898179] Kernel panic - not syncing: panic_on_warn set ...
[ 2230.898183] CPU: 3 PID: 1407 Comm: syz-executor.0 Not tainted 5.8.0-rc2+ #28
[ 2230.898190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014

Fixes: 3057224e ("mlxsw: spectrum_router: Implement FIB offload in deferred work")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Ferre says:

====================
net: macb: Wake-on-Lan magic packet fixes and GEM handling

Here is a split series to fix WoL magic-packet on the current macb driver. Only
fixes in this one based on current net/master.

Changes in v5:
- Addressed the error code returned by phylink_ethtool_set_wol() as suggested
  by Russell.
  If PHY handles WoL, MAC doesn't stay in the way.
- Removed Florian's tag on 3/5 because of the above changes.
- Correct the "Fixes" tag on 1/5.

Changes in v4:
- Pure bug fix series for 'net'. GEM addition and MACB update removed: will be
  sent later.

Changes in v3:
- Revert some of the v2 changes done in macb_resume(). Now the resume function
  supports in-depth re-configuration of the controller in order to deal with
  deeper sleep states. Basically as it was before changes introduced by this
  series
- Tested for non-regression with our deeper Power Management mode which cuts
  power to the controller completely

Changes in v2:
- Add patch 4/7 ("net: macb: fix macb_suspend() by removing call to netif_carrier_off()")
  needed for keeping phy state consistent
- Add patch 5/7 ("net: macb: fix call to pm_runtime in the suspend/resume functions") that prevent
  putting the macb in runtime pm suspend mode when WoL is used
- Collect review tags on 3 first patches from Florian: Thanks!
- Review of macb_resume() function
- Addition of pm_wakeup_event() in both MACB and GEM WoL IRQ handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>