This is a new device for this driver.
Reported-by: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Tobias Kluge <zielscheibe@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This data allow writing for example MTD driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Broadocm updated their code, this may be needed for newer hardware or
some corner cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k: Fix ANI monitoring" reverted an earlier
commit that adjusted ANI to improve performance. But, this causes
adverse effects in AP mode (as reported by Felix based on an OpenWrt
report). Use the older INI/period configuration for now until more
testing is done.

Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k: Add custom parameters for CUS198" didn't
pass the correct gpio value to ath9k_hw_cfg_output(). Fix it.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When trying to unset a previously-set multicast list (i.e. the new list
has 0 entries), mwifiex_set_multicast_list() was calling down to
mwifiex_request_set_multicast_list() while leaving
mcast_list.num_multicast_addr as an uninitialized value.

We were arriving at mwifiex_cmd_mac_multicast_adr() which would then
proceed to do an often huge memcpy of
mcast_list.num_multicast_addr*ETH_ALEN bytes, causing memory corruption
and hard to debug crashes.

Fix this by setting mcast_list.num_multicast_addr to 0 when no multicast
list is provided. Similarly, fix up the logic in
mwifiex_request_set_multicast_list() to unset the multicast list that
was previously sent to the hardware in such cases.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow a regulatory domain country code to be specified at boot
using a module argument.  This overrides the firmware regulatory
mode.

This patch also enables uAP to operate in 11a mode with hostapd.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make the commenting style consistent with networking block comment
style as suggested by checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Luciano Coelho <coelho@ti.com>

module_spi_driver() eliminates some boiler plate and makes code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The fw_status wasn't zeroed during allocation, resulting
in uninitialized var usage, and finally causing AP
traffic stop after recovery.

The wrong value in fw_status_2->counters.tx_lnk_free_pkts
led to a bad lnk->allocated_pkts calculation in
wlcore_fw_status(), causing wl18xx_lnk_low_prio() to return
FALSE (lnk->allocated_pkts > thold).
This eventually blocked the link in wlcore_tx_work_locked(),
as wl1271_skb_dequeue() continuously returned NULL.

Fix it by zeroing wl->fw_status_1/2 during allocation.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

u32 can be incorrect (too small) for some architectures.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Otherwise, if the work is pending, we might get
a bad dereference after the interface is removed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

When associating to an AP with WEP set the
default key upon association by implementing
the set_deafult_key_idx op.

Fixes auto-arp sent with wrong key_idx bug.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

In some R&D chips, the device may be left untrimmed and with the MAC
address missing from fuse ROM.  In order to support those devices,
apply a random locally administered MAC address instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>

The current code configures the peer caps only on BSS_CHANGED_HT
notification. However, we have to configure the peer caps
(and rates) even when HT is not enabled. Otherwise, the fw
continues working with low rates.

Configure the peer caps when sta_exists is true (i.e. when
we extracted the sta rates, e.g. on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Instead of doing all the sysfs file handling in the main file, move it
to a new sysfs source file to reduce the amount of code in a single
file.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Remove unnecessary includes; remove duplicate and useless defines; fix
copyright notice and remove some unnecessary line breaks.
Signed-off-by: Luciano Coelho <coelho@ti.com>

In PG2.0 there is an issue where PHY's FDSP Code RAM sometimes gets
corrupted when exiting from ELP mode. This issue is related to FDSP
Code RAM clock implementation.

PG2.1 introduces a HW fix for this issue that requires the driver to
change the FDSP Code Ram clock settings (mux it to ATGP clock instead
of its own clock).

This workaround uses PHY_FPGA_SPARE_1 register and is relevant to WL8
PG2.1 devices.

The fix is also backward compatible with older PG2.0 devices where the
register PHY_FPGA_SPARE_1 is not used and not connected.

The fix is done in the wl18xx_pre_upload function (must be performed
before uploading the FW code) and includes the following steps:

1. Disable FDSP clock
2. Set ATPG clock toward FDSP Code RAM rather than its own clock.
3. Re-enable FDSP clock
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

If "device is disconnected" check occurs to be true in ezusb_access_ltv(),
it just return -ENODEV. But that means request_context is leaked since
there are no any references to it anymore.
The patch adds a call to ezusb_request_context_put() before return.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.

Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201

Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"These are the pending NFC patches for the 3.11 merge window.

It contains the pending fixes that were on nfc-fixes (nfc-fixes-3.10-2),
along with a few more for the pn544 and pn533 drivers, the LLCP
disconnection path and an LLCP memory leak.

Highlights for this one are:

- An initial secure element API. NFC chipsets can carry an embedded
  secure element or get access to the SIM one. In both cases they
  control the secure elements and this API provides a way to discover,
  enable and disable the available SEs. It also exports that to
  userspace in order for SE focused middleware to actually do something
  with them (e.g. payments).

- NCI over SPI support. SPI is the most complex NCI specified transport
  layer and we now have support for it in the kernel. The next step will
  be to implement drivers for NCI chipsets using this transport like
  e.g. bcm2079x.

- NFC p2p hardware simulation driver. We now have an nfcsim driver that
  is mostly a loopback device between 2 NFC interfaces. It also
  implements the rest of the NFC core API like polling and target
  detection. This driver, with neard running on top of it, allows us to
  completely test the LLCP, SNEP and Handover implementation without
  physical hardware.

- A Firmware update netlink API. Most (All ?) HCI chipsets have a
  special firmware update mode where applications can push a new
  firmware that will be flashed. We now have a netlink API for providing
  that mode to e.g. nfctool."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix checkpatch warnings.
Replace __attribute__((__packed__)) with __packed.
Replace spaces with tabs.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WKS (Well Known Services) bitmask should be transmitted in big endian
order. Picky implementations will refuse to establish an LLCP link when the
WKS bit 0 is not set to 1. The vast majority of implementations out there
are not that picky though...
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In order to advertise our LLCP support properly and to follow the LLCP
specs requirements, we need to initialize the WKS (Well-Known Services)
bitfield to 1 as SAP 0 is the only mandatory supported service.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When we receive a RNR, the remote is busy processing the last received
frame. We set a local flag for that, and we should send a SYMM when it
is set instead of sending any pending frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Without the new LLCP_CONNECTING state, non blocking sockets will be
woken up with a POLLHUP right after calling connect() because their
state is stuck at LLCP_CLOSED.
That prevents userspace from implementing any proper non blocking
socket based NFC p2p client.

Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This driver declares two virtual NFC devices supporting NFC-DEP protocol.
An LLCP connection can be established between them and all packets sent
from one device is sent back to the other, acting as loopback devices.

Once established, the LLCP link can be disconnected by disabling the target
device (with rfkill, nfctool, or neard disable-adapter test script).
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In nfc_llcp_tx_work() the sk_buff is not freed when the llcp_sock
is null and the PDU is an I one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch keeps the socket alive and therefore does not remove
it from the sockets list in the local until the DISC PDU has been
actually sent. Otherwise we would reply with DM PDUs before sending
the DISC one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

nfc_llcp_send_disconnect() already exists but is not used.
nfc_llcp_disconnect() naming is not consistent with other PDU
sending functions.
This patch removes nfc_llcp_send_disconnect() and renames
nfc_llcp_disconnect()
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Instead of dumping ACR122 frames as errors, we use the print_hex_dump()
dynamic debug APIs.
We also print an accurate IC version, as the ACR122 is pn532 based.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Enabling or disabling an NFC accessible secure element through netlink
requires giving both an NFC controller and a secure element indexes.
Once enabled the secure element will handle card emulation once polling
starts.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Called via netlink, this API will enable or disable a specific secure
element. When a secure element is enabled, it will handle card emulation
and more generically ISO-DEP target mode, i.e. all target mode cases
except for p2p target mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>