- 15 Jun, 2011 10 commits
-
-
Dmitry Kravkov authored
Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
David S. Miller <davem@conan.davemloft.net>
-
Dmitry Kravkov authored
Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
-
Yaniv Rosner authored
Signed-off-by:
Yaniv Rosner <yanivr@broadcom.com> Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
-
Dmitry Kravkov authored
It's not needed any more since device always operates in interrupt-driven mode Signed-off-by:
-
Dmitry Kravkov authored
Signed-off-by:
-
Michael Chan authored
The hardware indexing scheme for the FCoE kcq will change in the upcoming firmware. This patch will cope with the change easily. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
- 13 Jun, 2011 13 commits
-
-
Neil Horman authored
While doing some backporting I noticed that vmxnet3 had a variable that was set but never used. Get rid of it, and stop the compiler from griping Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: "VMware, Inc." <pv-drivers@vmware.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
Bhavesh Davda <bhavesh@vmware.com> Signed-off-by:
-
Peter Pan(潘卫平) authored
Dan Carpenter found that there was a dereference before a check, added in 56d00c67(bonding:delete lacp_fast from ad_bond_info). Signed-off-by:
Weiping Pan <panweiping3@gmail.com> Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com> Signed-off-by:
-
Eric Dumazet authored
l2tp_ip_sendmsg() in non connected mode incorrectly calls sk_setup_caps(). Subsequent send() calls send data to wrong destination. We can also avoid changing dst refcount in connected mode, using appropriate rcu locking. Once output route lookups can also be done under rcu, sendto() calls wont change dst refcounts too. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> CC: James Chapman <jchapman@katalix.com> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the smsc9420. Compile tested only. Cc: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by:
Richard Cochran <richard.cochran@omicron.at> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the STMicroelectronics Ethernet driver. Compile tested only. Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the RDC R6040 Fast Ethernet MAC. Compile tested only. Cc: Florian Fainelli <florian@openwrt.org> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the OpenCores 10/100 MAC driver. Compile tested only. Cc: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping in the "Dave ethernet interface." Compile tested only. Cc: Ilya Yanok <yanok@emcraft.com> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the TIGON3 driver. Compile tested only. Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Richard Cochran authored
This patch enables software (and phy device) transmit time stamping for the DaVinci EMAC driver. Tested together with the dp83640 PHY. Cc: Anant Gole <anantgole@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by:
-
Richard Cochran authored
The DaVinci EMAC driver does not implement any ioctls, but still it can pass them through to the phy device. This makes it possible for a phy to offer PHC capabilities. Cc: Anant Gole <anantgole@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by:
-
Richard Cochran authored
This patch has been tested on the Freescale M5234BCC, which includes the National Semiconductor DP83640 with IEEE 1588 support. Cc: Greg Ungerer <gerg@uclinux.org> Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de> Cc: Shawn Guo <shawn.guo@freescale.com> Signed-off-by:
-
Richard Cochran authored
The network stack provides the function, skb_clone_tx_timestamp(). Ethernet MAC drivers can call this via the transmit time stamping hook, skb_tx_timestamp(). This commit exports the clone function so that drivers using it can be compiled as modules. Signed-off-by:
-
- 11 Jun, 2011 9 commits
-
-
Eric Dumazet authored
SNMP mibs use two percpu arrays, one used in BH context, another in USER context. With increasing number of cpus in machines, and fact that ipv6 uses per network device ipstats_mib, this is consuming a lot of memory if many network devices are registered. commit be281e55 (ipv6: reduce per device ICMP mib sizes) shrinked percpu needs for ipv6, but we can reduce memory use a bit more. With recent percpu infrastructure (irqsafe_cpu_inc() ...), we no longer need this BH/USER separation since we can update counters in a single x86 instruction, regardless of the BH/USER context. Other arches than x86 might need to disable irq in their irqsafe_cpu_inc() implementation : If this happens to be a problem, we can make SNMP_ARRAY_SZ arch dependent, but a previous poll ( https://lkml.org/lkml/2011/3/17/174 ) to arch maintainers did not raise strong opposition. Only on 32bit arches, we need to disable BH for 64bit counters updates done from USER context (currently used for IP MIB) This also reduces vmlinux size : 1) x86_64 build $ size vmlinux.before vmlinux.after text data bss dec hex filename 7853650 1293772 1896448 11043870 a8841e vmlinux.before 7850578 1293772 1896448 11040798 a8781e vmlinux.after 2) i386 build $ size vmlinux.before vmlinux.afterpatch text data bss dec hex filename 6039335 635076 3670016 10344427 9dd7eb vmlinux.before 6037342 635076 3670016 10342434 9dd022 vmlinux.afterpatch Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Bohac authored
1) the setting of NETIF_F_VLAN_CHALLENGED in bond_del_vlan() is useless since commit b2a103e6 because bond_fix_features() now sets NETIF_F_VLAN_CHALLENGED whenever the last slave is being removed. 2) the code never triggers anyway as vlan_list is never empty since ad1afb00. Signed-off-by:
Jiri Bohac <jbohac@suse.cz> Signed-off-by:
-
Alexey Dobriyan authored
Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Padmanabh Ratnakar authored
NETIF_F_TSO6 for VLAN packets was not enabled for BE adapters. Enabling it. Signed-off-by:
Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by:
-
Jason Wang authored
There's no need for the guest to validate the checksum if it have been validated by host nics. So this patch introduces a new flag - VIRTIO_NET_HDR_F_DATA_VALID which is used to bypass the checksum examing in guest. The backend (tap/macvtap) may set this flag when met skbs with CHECKSUM_UNNECESSARY to save cpu utilization. No feature negotiation is needed as old driver just ignore this flag. Iperf shows 12%-30% performance improvement for UDP traffic. For TCP, when gro is on no difference as it produces skb with partial checksum. But when gro is disabled, 20% or even higher improvement could be measured by netperf. Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Ben Dooks authored
Given many versions of ethtool's reluctance to do anything other than byte accesses to the EEPROM interface, it is easier to update the driver to support byte accesses so that all the ethtool versions that have been observed in Debian can write the EEPROM. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Michio Honda authored
Signed-off-by:
Michio Honda <micchie@sfc.wide.ad.jp> Acked-by:
Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by:
-
Po-Yu Chuang authored
FTGMAC100 Ethernet Media Access Controller supports 10/100/1000 Mbps and MII/GMII. This driver has been working on some ARM/NDS32 SoC's including Faraday A369 and Andes AG102. Signed-off-by:
Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by:
-
Geert Uytterhoeven authored
arch/m68k/emu/nfeth.c: In function ‘nfeth_init’: arch/m68k/emu/nfeth.c:243: error: implicit declaration of function ‘request_irq’ arch/m68k/emu/nfeth.c:243: error: ‘IRQF_SHARED’ undeclared (first use in this function) arch/m68k/emu/nfeth.c:243: error: (Each undeclared identifier is reported only once arch/m68k/emu/nfeth.c:243: error: for each function it appears in.) arch/m68k/emu/nfeth.c: In function ‘nfeth_cleanup’: arch/m68k/emu/nfeth.c:266: error: implicit declaration of function ‘free_irq’ drivers/net/apne.c: In function ‘apne_probe’: drivers/net/apne.c:189: error: implicit declaration of function ‘free_irq’ drivers/net/apne.c: In function ‘apne_probe1’: drivers/net/apne.c:317: error: implicit declaration of function ‘request_irq’ drivers/net/apne.c:317: error: ‘IRQF_SHARED’ undeclared (first use in this function) drivers/net/apne.c:317: error: (Each undeclared identifier is reported only once drivers/net/apne.c:317: error: for each function it appears in.) Introduced by commit a6b7a407 ("net: remove interrupt.h inclusion from netdevice.h"). Include <linux/interrupt.h> in the individual drivers to fix the build. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
- 10 Jun, 2011 8 commits
-
-
Greg Rose authored
Signed-off-by:
Greg Rose <gregory.v.rose@intel.com> Tested-by:
Evan Swanson <evan.swanson@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Greg Rose authored
The message size allocated for rtnl ifinfo dumps was limited to a single page. This is not enough for additional interface info available with devices that support SR-IOV and caused a bug in which VF info would not be displayed if more than approximately 40 VFs were created per interface. Implement a new function pointer for the rtnl_register service that will calculate the amount of data required for the ifinfo dump and allocate enough data to satisfy the request. Signed-off-by:
-
Carolyn Wyborny authored
This patch changes the way versioning is done for igb in the kernel by removing the number after the "k." It has been determined that just the "k" is sufficient to identify a kernel version and the following number was used in an inconsistent manner. Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
-
Williams, Mitch A authored
Update the version number to match version conventions. Bump the major version to indicate that new hardware support (i350) has been added. Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Bruce Allan authored
Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
-
Bruce Allan authored
Commit 5d03078a added a redundant 'select CRC32'; remove it. Signed-off-by:
-
Bruce Allan authored
The Host Wakeup Active bit in the PHY Port General Configuration register (page 769 register 17) must be cleared after every PHY reset to prevent an unexpected wake signal from the PHY. Originally, this was accomplished by simply reading the PHY Wakeup Control register on page 800 which clears the Host Wakeup Active bit as a side-effect. Unfortunately, a hardware bug on the 82577 and 82578 PHY can cause unexpected behavior when registers on page 800 are accessed while in gigabit mode. This patch changes the remaining instances when the Host Wakeup Active bit needs to be cleared while possibly in gigabit mode by accessing the Port General Configuration register directly instead of accessing any register on page 800. Signed-off-by:
-
Bruce Allan authored
Doing a PHY page select can take a long time, relatively speaking. This can cause a significant delay when updating a number of PHY registers on the same page by unnecessarily setting the page for each PHY access. For example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[], SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which takes a long time which can cause issues when suspending. This patch introduces new PHY ops function pointers to allow callers to set the page directly and do any number of PHY accesses on that page. This feature is currently only implemented for 82577, 82578 and 82579 PHYs for both the normally addressed registers as well as the special- case addressing of the PHY wakeup registers on page 800. For the latter registers, the existing function for accessing the wakeup registers has been divided up into three- 1) enable access to the wakeup register page, 2) perform the register access and 3) disable access to the wakeup register page. The two functions that enable/disable access to the wakeup register page are necessarily available to the caller so that the caller can restore the value of the Port Control (a.k.a. Wakeup Enable) register after the wakeup register accesses are done. All instances of writing to multiple PHY registers on the same page are updated to use this new method and to acquire any PHY locking mechanism before setting the page and performing the register accesses, and release the locking mechanism afterward. Some affiliated magic number cleanup is done as well. Signed-off-by:
-
