Add support for SST38VF640x chips in CFI mode.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: yidong zhang <zhangyd6@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When block2mtd_erase fails, a duplicated assignment instantly
changes instr->state from MTD_ERASE_FAILED to MTD_ERASE_DONE.

It looks to me like this might not be intended, or is it?
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-By: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.

For former nand driver, it had the two functions:

1. detecting nand flash partitions;
2. registering elbc interrupt.

Now, second function is removed to fsl_lbc.c.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Use the more standard #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
No change in output strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The suspend & resume called from mtd core. So no need to call at driver.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

RAW writes were broken by 782ce79a
which introduced a check of ops->ooboffs in nand_do_write_ops().

When writing in RAW mode this is called with an ops struct on the stack
of mtdchar.c:mtd_write() which does not initialise ops->ooboffs, so it
is garbage and fails this test.

This test does not make sense if ops->oobbuf is NULL, which it is in the
RAW write path, so include that in the test.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Convert a sequence of kmalloc and memcpy to use kmemdup.

The semantic patch that performs this transformation is:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression a,flag,len;
expression arg,e1,e2;
statement S;
@@

  a =
-  \(kmalloc\|kzalloc\)(len,flag)
+  kmemdup(arg,len,flag)
  <... when != a
  if (a == NULL || ...) S
  ...>
- memcpy(a,arg,len+1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

I didn't know that kernel allows use of that typedef.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

It turns out that pci core now handles these, so this code is redundant
and can even cause bugs
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There is small race window that could make kthread_stop hang forever.
I found that while hacking the IR subsystem.
Signed-off-by: Maxim Levitsky <maximlevisky@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

It not needed, because I already added locking for all fops
methods.
Signed-off-by: Maxim Levitsky <maximlevisky@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now it once again possible to remove mtdtrans module.
You still need to ensure that block devices of that module aren't mounted.
This is due to the fact that as long as a block device is open, it still exists,
therefore if we were to allow module removal, this block device might became used again.

This time in addition to code review, I also made the code
pass some torture tests like module reload in  a loop + read in a loop +
card insert/removal all at same time.

The blktrans_open/blktrans_release don't take the mtd table lock because:

While device is added (that includes execution of add_mtd_blktrans_dev)
the lock is already taken

Now suppose the device will never be removed. In this case even if we have changes
in mtd table, the entry that we need will stay exactly the same. (Note that we don't
look at table at all, just following private pointer of block device).

Now suppose that someone tries to remove the mtd device.
This will be propagated to trans driver which _ought_ to call del_mtd_blktrans_dev
which will take the per device lock, release the mtd device and set trans->mtd = NULL.
>From this point on, following opens won't even be able to know anything about that mtd device
(which at that point is likely not to exist)
Also the same care is taken not to trip over NULL mtd pointer in blktrans_dev_release.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

As reported on lkml, building this module for HIMEM systems spews warnings
about mismatch in pointer types.  Further, we need to use ioremap() in order
to properly access the flash memory on most systems rather than just doing
it directly.
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The bbt structure isn't actually used, just the badblockpos.  This lets
the driver correctly handle badblocks with the different OOB layout with
certain sized flashes.  Previously, the blocks would all be reported as
bad and be completely unusable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

- remove disabled code (hasn't been touched since the beginning of git
  and should be reimplemented if really needed)
- convert remaining c++-comments to plain c-style
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

For 4Gib non-DDP chip it does not follow that it is always 4KiB page chip.
The number of data buffers is checked and if it is equal to 1
we suppose that it is 4KiB page onenand chip.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch changes the loop over the "reg" tuples to not exit
directly upon of_address_to_resource() failure but to continue
with the next "reg" tuple instead. This failure could be due to
size = 0, which might be passed via the device-tree.

This is needed for boards, where a "reg" tuple might have size 0
(of_address_to_resource() returns with EINVAL when size = 0).

Example:

Fully equipped board:

	reg = <0 0x00000000 0x00400000
	       0 0x00400000 0x00400000>;

Partially equipped board:

	reg = <0 0x00000000 0x00400000
	       0 0x00400000 0x00000000>;

This could be the case on boards with runtime detection of
multiple NOR flash configurations where the detected flash size
is inserted into the dtb in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Scanning 1024 bytes to see if an EB is empty is a bit much.
Lower it to 256 bytes and make sure the while loop is
optimized.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Drop the alloc_sem before erasing flash in
jffs2_garbage_collect_pass().
Otherwise writes are put on hold until the erase
has finised.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch fixes sparse warning for static declaration of variable "use_dma"

drivers/mtd/nand/omap2.c:114:11: warning: symbol 'use_dma' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When JFFS2 is used for large volumes, the mount times are quite long.
Increasing the hash size provides a significant speed boost on the OLPC
XO-1 laptop.

Add logic that dynamically selects a hash size based on the size of
the medium. A 64mb medium will result in a hash size of 128, and a 512mb
medium will result in a hash size of 1024.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove tabs between type and name.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

- *var instead of * var
- proper multiline comment
- func(args) instead of func (args)
- 80 lines

So from
|total: 2 errors, 37 warnings, 654 lines checked
we got to one warning.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds the appropriate conversions to correct the endianness
issues in the MTD driver whenever it accesses the device tree (which is
always big endian).
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

I used this to check the BBT on flash together with a hack in mtdchar in
order to read bad blocks.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

it will create an empty BBT table without considering vendor's BBT
information. Vendor's information may be unavailable if the NAND
controller has a different DATA & OOB layout or this information may be
allready purged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The first (sixt) byte in the OOB area contains vendor's bad block
information. During identification of the NAND chip this information is
collected by scanning the complete chip.
The option NAND_USE_FLASH_BBT is used to store this information in a sector so
we don't have to scan the complete flash. Unfortunately the code stores
a marker in order to recognize the BBT in the OOB area. This will fail
if the OOB area is completely used for ECC.
This patch introduces the option NAND_USE_FLASH_BBT_NO_OOB which has to be
used with NAND_USE_FLASH_BBT. It will then store BBT on flash without
touching the OOB area. The BBT format on flash remains same except the
first page starts with the recognition pattern followed by the version byte.
This change was tested in nandsim and it looks good so far :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

No code change.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

S5PC210 has the same OneNAND controller as S5PC110
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Implement DMA interrupt method. previous time it polls the DMA status.
It can reduce the CPU power but decrease the performance a little.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When use HIGHMEM, dma_map_single doesn't get the proper DMA address.
So use the dma_map_page in this case.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

After S5PC110 use the generic method for OneNAND.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The MLC NAND Flash differs from the SLC NAND flash in functioning
and the cell structure. Therefore we are considering it as a
different Flash type.
Signed-off-by: Rohit H.S <rohit.hs@samsung.com>
Signed-off-by: Raghav Gupta <gupta.raghav@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

MLC NAND Flash has a different cell structure and differs in
functioning than the SLC NAND Flash. Hence we are considering it as
a different Flash type.
Signed-off-by: Rohit H.S <rohit.hs@samsung.com>
Signed-off-by: Raghav Gupta <gupta.raghav@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There's no case timeout but add it for some H/W problem or
wrong codes implementation
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>