Add support for the Solomon SSD1307 OLED controller found on the
Crystalfontz CFA10036 board.

This controller can drive a display with a resolution up to 128x39 and can
operate over I2C or SPI.

The current driver has only been tested on the CFA-10036, that is using
this controller over I2C to driver a 96x16 OLED screen.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Thomas Petazzoni <thomas@free-electrons.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The revision check fails for the beaglebone; Add new revision ID.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Exynos DP changes for the 3.8 merge window.

- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.

* 'exynos-dp-next' of git://github.com/jingoo/linux:
  video: exynos_dp: remove redundant parameters
  video: exynos_dp: Fix incorrect setting for INT_CTL
  video: exynos_dp: Reset and initialize DP before requesting irq
  video: exynos_dp: Enable hotplug interrupts
  video: exynos_dp: Move hotplug into a workqueue
  video: exynos_dp: Remove sink control to D0
  video: exynos_dp: Fix bug when checking dp->irq
  video: exynos_dp: Improve EDID error handling
  video: exynos_dp: Get pll lock before pattern set
  video: exynos_dp: Clean up SW link training
  video: exynos_dp: Check DPCD return codes
  video: exynos_dp: device tree documentation
  video: exynos_dp: Add device tree support to DP driver

Samsung Framebuffer changes for the 3.8 merge window.

- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.

* 'samsung-fb-next' of git://github.com/jingoo/linux:
  video: s3c-fb: fix red offset and length for ARGB232 format
  video: s3c-fb: return an error when bpp is invalid
  video: s3c-fb: add "drop through" comment
  video: s3c-fb: use dev_get_drvdata() instead of platform_get_drvdata()
  video: s3c-fb: use FIMD_V8_VIDTCON0 for EXYNOS5 FIMD
  video: s3c-fb: fix help message for FB_S3C_DEBUG_REGWRITE
  video: s3c-fb: fix typo in comment
  video: s3c-fb: add the bit definitions for VIDCON0_VIDOUT_WB
  video: s3c-fb: move the bit definitions for DITHMODE register
  video: s3c-fb: move the bit definitions for WINxMAP and WPALCON register
  video: s3c-fb: move the bit definitions for VIDINTCON0 register
  video: s3c-fb: move the address definition for VIDOSD register
  video: s3c-fb: move the address definitions for VIDTCON registers
  video: s3c-fb: clean the bit definition for WINCON register

This patch cleans up few redundant parameters keeping
the same functionality intact.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

INT_CTL register contains bits INT_POL0 and INT_POL1, and not INT_POL.
This patch fixes the wrong register setting for INT_CTL.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

If DP is not reset properly before kernel bootup(in bootloader code),
there can be few pending interrupts, and sometimes they invoke
DP irq handler as soon as the irq handler is registered in DP probe.
So, we make the DP driver more robust by resetting and
initializing DP at the earliest and then registering the irq handler.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Enable hotplug interrupts and move the hotplug scheduling into the
interrupt handler. This allows us to introduce a screen at any time
while we're running.

[jg1.han@samsung.com: moved the bit masking of hotplug interrupts]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Move the hotplug related code from probe and resume into a workqueue.
This allows us to initialize the DP driver (and resume it) when there
is no monitor connected.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

According to DP spec, it is not required in the Link Training
procedure.

[jg1.han@samsung.com: modified the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Fix a bug where we check !dp->irq instead of the correct check for
-ENXIO.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

EDID error handling has 2 problems:
 - It doesn't fail as early as it can
 - The retry counts for i2c and aux transactions are huge

This patch fails if the initial i2c transaction fails, and reduces the
aux and i2c retry counts down to 3.

[jg1.han@samsung.com: reduced the retry count of exynos_dp_read_byte_from_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

According to the exynos datasheet (Figure 49-10), we should wait for PLL
lock before programming the training pattern when doing software eDP
link training.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Clean up some of the SW training code to make it more clear and reduce
duplicate code.

[jg1.han@samsung.com: used exynos_dp_write_bytes_to_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Add return code checks to the DPCD transactions in the SW link training
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Add documentation for the DT bindings in exynos display port driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

This patch enables device tree based discovery support for DP driver.
The driver is modified to handle platform data in both the cases:
with DT and non-DT.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

* 'fbdev-next' of github.com:timur-tabi/linux-2.6:
  drivers/video: fsl-diu-fb: store EDID data in the global object
  drivers/video: fsl-diu-fb: don't touch registers for unused features
  drivers/video: fsl-diu-fb: clean up reset of primary display
  drivers/video: fsl-diu-fb: remove unused 'cursor_reset' variable
  drivers/video: fsl-diu-fb: improve message displays
  drivers/video: fsl-diu-fb: streamline enabling of interrupts
  drivers/video: fsl-diu-fb: add support for set_gamma ioctls
  drivers/video: fsl-diu-fb: simplify platforms that have only one port
  MAINTAINERS: Make Timur Tabi the maintainer for the Freescale DIU driver

do clk_get on connection id "fck" to support OMAP based
platforms having multiple clocks for module. Without this
driver change clk_get fails on am335x.

This patch is based on the discussion in community
http://marc.info/?l=linux-kernel&m=135166018907827&w=2Signed-off-by: Manjunathappa <prakash.pm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.

Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Merge SH Mobile LCDC patches from Laurent.

* 'lcdc-next' of git://linuxtv.org/pinchartl/fbdev:
  fbdev: sh_mobile_lcdc: Make sh_mobile_lcdc_sys_bus_ops static
  sh: kfr2r09: Use the backlight API for brightness control
  ARM: mach-shmobile: ag5evm: Use the backlight API for brightness control
  fbdev: sh_mobile_lcdc: Remove unused get_brightness pdata callback
  sh: ecovec24: Remove unused get_brightness LCDC callback
  sh: ap325rxa: Remove unused get_brightness LCDC callback
  ARM: mach-shmobile: mackerel: Removed unused get_brightness callback
  fbdev: sh_mobile_lcdc: Store the backlight brightness internally
  fbdev: sh_mipi_dsi: Remove the unused sh_mipi_dsi_info lcd_chan field
  ARM: mach-shmobile: Remove the unused sh_mipi_dsi_info lcd_chan field
  fbdev: sh_mipi_dsi: Remove last reference to LCDC platform data
  fbdev: sh_mipi_dsi: Use the LCDC entity default mode
  fbdev: sh_mipi_dsi: Use the sh_mipi_dsi_info channel field
  ARM: mach-shmobile: Initiliaze the new sh_mipi_dsi_info channel field
  fbdev: sh_mipi_dsi: Add channel field to platform data
  ARM: mach-shmobile: ag5evm: Add LCDC tx_dev field to platform data
  fbdev: sh_mobile_lcdc: Remove priv argument from channel and overlay init
  fbdev: sh_mobile_lcdc: Rename mode argument to modes
  fbdev: sh_mobile_lcdc: Get display dimensions from the channel structure
  fbdev: sh_mobile_lcdc: use dma_mmap_coherent

Although the DIU driver creates five framebuffer devices, only the first
one controls the physical display.  The remaining four are virtual "AOIs".
Therefore, the EDID data should be stored in the global fsl_diu_data
object, instead of the per-framebuffer object.
Signed-off-by: Timur Tabi <timur@freescale.com>

We don't use the writeback buffer, so don't initialize the registers for
that feature.

The default value for SYN_POL is already zero, so don't re-initialize it.

Writing the INT_STATUS register does nothing.

The value that we write to the PLUT register only makes sense on the
MPC8610 and P1022, so don't touch that register on the MPC5121.
Signed-off-by: Timur Tabi <timur@freescale.com>

Commit 4b5006ec ("shared DIU framebuffer support") added the ability to
retain the splash screen until the framebuffer is opened by user space.
Clean up this code to eliminate redundant writes to registers, and eliminate
the use of dummy area descriptor.
Signed-off-by: Timur Tabi <timur@freescale.com>

Probably left over from initial development in hardware cursor support
that never made it upstream.
Signed-off-by: Timur Tabi <timur@freescale.com>

Add some debug and error messages that are useful during debugging.
Signed-off-by: Timur Tabi <timur@freescale.com>

Remove functions request_irq_local() and free_irq_local(), and merge
their code into the functions that handle opening and closing the
framebuffer.  We also improve the way that interrupts are enabled.

Also implement a work-around for broken U-Boots that leave the DIU
interrupts enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>

The MPC5121 BSP comes with a gamma_set utility that initializes the gamma
table via an ioctl.  Unfortunately, the ioctl number that utility uses
is defined improperly, but we can still support it.
Signed-off-by: Timur Tabi <timur@freescale.com>

Allow the platform code not to define a value for diu_ops.set_monitor_port.
This would be for platforms that only have one monitor port.
set_monitor_port() will never be called with an unsupported port anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>

Timur has been cleaning up this driver, so just make it official.
Signed-off-by: Timur Tabi <timur@freescale.com>

Green pixel and blue pixel are 3 bits and 2 bits respectively
at ARGB232 format. Thus, the value of red offset should be 5,
not 4. Also, the value of red length should be 2, because
red pixel is 2 bits at ARGB232 format.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

This patch returns an error, when bpp is invalid in
s3c_fb_check_var(). If invalid bpp is requested,
an error should be returned.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

This patch adds a "drop through" comment to improve
the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

Because there is no need to access to the platform device in
suspend/resume and runtime_suspend/resume, dev_get_drvdata()
can be used instead of platform_get_drvdata() to make the code
smaller.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

This patch uses FIMD_V8_VIDTCON0 as the address definition
of VIDTCON0 register, because the address offset of VIDTCONx
registers is changed from 0x0 to 0x20000 for EXYNOS5 FIMD.
So, FIMD_V8_VIDTCON0 should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

The help message of config FB_S3C_DEBUG_REGWRITE is fixed,
because printk(KERN_DEBUG) was replaced with pr_debug().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

"sturucture" should be "structure".
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

This patch adds the bit definitions for VIDCON0_VIDOUT_WB.
These definitions are used to support writeback for RGB and
i80 interface. Also, output format of writeback is YUV444.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>

The bit definitions for DITHMODE registers are moved according to
address order. Also, the bit definition of VIDCON1_FSTATUS_EVEN
is moved.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>